SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage Multiport Series - MS-013 Pb e3 RoHS Description Fixed Voltage Multiport Series MS-013 are SIDACtor® components designed to protect sensitive SLIC (Subscriber Line Interface Circuit) devices from damaging overvoltage transients. The series provides a high surge current rated dual port protection solution incorporating a fixed voltage switching threshold for negatives surges. All positive surges are routed through an internal diode to a ground reference. Features and Benefits • Low voltage overshoot Agency Approvals positive voltage surges • Low on-state voltage Agency • Does not degrade surge capability after multiple surge events within limit. Agency File Number E133083 6 2 5 3 4 6 (T2) 2 (G1) 5 (G2) 3 (R1) 4 (R2) • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) • Two-port protection • Integrated diodes for Applicable Global Standards Schematic Symbol 1 (T1) • Replaces four discrete components • Fails short circuit when surged in excess of ratings Pinout Designation 1 • RoHS compliant and Halogen-free • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 • ITU K.20/21 Enhanced Level* • YD/T 1082 • YD/T 993 • ITU K.20/21 Basic Level • YD/T 950 • GR 1089 Inter-building* *A-rated parts require series resistance Electrical Characteristics Part Number P0641UALxx P0721UALxx P0901UALxx P1101UALxx P1301UALxx P1701UALxx P0641UCLxx P0721UCLxx P0901UCLxx P1101UCLxx P1301UCLxx P1701UCLxx Marking P0641UA P0721UA P0901UA P1101UA P1301UA P1701UA P0641UC P0721UC P0901UC P1101UC P1301UC P1701UC VDRM @lDRM=5µA VS @100V/µs IH IS IT VT @IT=2.2 Amps VF V min V max mA min mA max A max V max V max 58 65 75 95 120 160 58 65 75 95 120 160 77 88 98 130 160 200 77 88 98 130 160 200 120 120 120 120 120 120 120 120 120 120 120 120 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 Capacitance See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are not appropriate for positive ringing systems - All electrical characteristics shown are defined from Tip (pins 1 & 6) to Ground (pins 2 & 5), and Ring (pins 3 & 4) to Ground (pins 2 & 5) - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/05/16 SIDACtor ® Protection Thyristors SLIC Protection Capacitance Values pF Pin 1-2 / 3-2 (4-5/6-5) Tip-Ground, Ring-Ground MIN MAX Part Number P0641UALxx P0721UALxx P0901UALxx P1101UALxx P1301UALxx P1701UALxx P0641UCLxx P0721UCLxx P0901UCLxx P1101UCLxx P1301UCLxx P1701UCLxx 50 45 40 40 35 30 65 60 60 50 35 40 pF Pin 1-3 (4-6) Tip-Ring MIN MAX 205 195 180 160 160 125 205 195 180 160 160 125 30 20 20 15 15 15 40 20 20 15 15 15 135 125 115 105 100 80 130 125 115 105 100 80 Note: Off-state capacitance (CO) is measured at 1 MHz with a -2V bias. Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/µs max 0.2/310 1 0.5/700 2 2/10 1 2/10 2 8/20 1 1.2/50 2 10/160 1 10/160 2 10/560 1 10/560 2 5/320 1 9/720 2 10/360 1 10/360 2 10/1000 1 10/1000 2 5/310 1 10/700 2 A min A min A min A min A min A min A min A min A 20 150 150 90 50 75 75 45 75 20 500 C 50 500 400 200 150 200 175 100 200 30 500 Notes: 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +125 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 60 °C/W Modified MS-013 6 5 4 1 2 3 Additional Information Datasheet Resources © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/05/16 Samples SIDACtor ® Protection Thyristors SLIC Protection V-I Characteristics tr x td Pulse Waveform VF VS VDRM VT -V +V IDRM IH IS IT IPP – Peak Pulse Current – %IPP +I 100 Waveform = tr x td 50 0 td tr t – Time (µs) Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 °C 4 2 IH (TC = 25ºC) 2.0 14 12 Ratio of Percent of VS Change – % Half Value 0 -I Normalized VS Change vs. Junction Temperature tr = rise time to peak value td = decay time to half value Peak Value 0 -4 -6 1.8 1.6 1.4 1.0 0.8 0.6 0.4 -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C 25°C 1.2 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/05/16 SIDACtor ® Protection Thyristors SLIC Protection Soldering Parameters Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL Recognized epoxy meeting flammability classification V-0 Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VDC ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 MS-013 Part Marking Drawing_2009-03-05.eps Part Numbering Part Marking P xxx1 U x L xx TYPE P=SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/05/16 PACKING OPTIONS XXXXXXX RoHS COMPLIANT IPP RATING Part Marking Code (Refer to Electrical Characteristics Table) Date Code XXXXX SIDACtor ® Protection Thyristors SLIC Protection Dimensions — MS-013 Dimensions 0.065 (1.65) Pad Outline C D J 7º TYP A Dimension are in inches (and millimeters). 0.059 (1.50) E 7º TYP A B C D E F G H J K BSC* 0.460 (11.68) 0.138 (3.50) G Burr Side H 96º A Mold Split Line 4º A 7º TYP BSC* F 7º TYP MIN Length of Flat Detail A K B Inches Millimeters Min Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 0.143 3.63 * BSC = Basic Spacing between Centers Packing Options Package Type U Description Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D Modified MS-013 6-pin Tube Pack 500 (50 per tube) TP N/A Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Dimensions — MS-013 Message Location .045 (1.14) .310 (7.87) 90˚ .165 (4.19) 6 Interior of the Tube .150 (3.81) .225 (5.72) .525 (13.34) .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .005 A 20.000 ± .030 (508.00 ± 0.76) .110 (2.79) A Dimensions are in inches (and millimeters) © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/05/16