TECHNICAL NOTE High performance video signal Switcher Triple Circuits Video Signal Switchers BA7602F, 03F, 06F/FS, 07F, 09F, 27FV ●Description These video switching ICs, which contain two or three 2-input circuits, were developed for switching TV, DVD, and other video signals. Input pin formats can be selected from bias mode (R=20 kΩ), sync-tip mode, and pedestal clamp mode. Having a large dynamic range and broad frequency characteristics, these switches are suited to a wide range of applications from audio signals to video signals. ●Features 1) Contain three 2-input, 1-output switch circuits (BA7602F,03F,06F/06FS,07F,09F,27FV) 2) Power supply voltage (4.5~5.5 V) 3) Low power consumption 4) Good frequency characteristics 5) Large dynamic range 6) Bias input (BA7602F) Sync-tip clamp input (BA7603F) Pedestal clamp input (BA7606F/06FS) Bias input + sync-tip clamp input (BA7607F,09F, 27FV) 7) Large input impedance (Typ.20kΩ) 8) Fast switching speed (Typ. 50ns) ●Use For switching TV, DVD, and Other video signals ●Lineup Part No. Circuit current （mA） Built-in circuit Input type BA7602F BA7603F 14.0 13.0 2 in 3 circuits 2 in 3 circuits BA7606F/FS 15.0 2 in 3 circuits BA7607F 12.5 2 in 3 circuits BA7609F 12.5 2 in 3 circuits BA7627FV 12.5 2 in 3 circuits Bias Clamp Pedestal Clamp Clamp 2 Bias1 Clamp 1 Bias 2 Clamp 2 Bias1 Distortion （％） Maximum output level （VP-P） － － 3.1 2.9 － 2.6 0.007 3.0 SOP16 0.007 3.0 SOP16 0.007 3.0 SSOP-B16 Package SOP16 SOP16 SOP16/ SSOP-A16 Aug. 2008 ●Absolute Maximum Ratings（Ta=25℃） Parameter Symbol Supply voltage Vcc BA7602F BA7603F BA7606F Power BA7607F Pd dissipation BA7609F BA7606FS BA7627FV Operating temperature Topr Storage temperature Tstg Limits 9 Unit V 500 *1 mW 650 *2 450 *1 －40～＋85 －55～＋125 ℃ ℃ *1 Deratings is done at 5.0mW/℃ above Ta=25℃.（BA7604N, 05N ,02F, 03F, 06F, 07F, 09F, 27FV） *2 Deratings is done at 6.5mW/℃ above Ta=25℃.（BA7606FS） ●Operating Range（Ta=25℃） Parameter Symbol Supply voltage Vcc Min. 4.5 Typ. 5.0 Max. 5.5 ●Electrical characteristics (Unless otherwise noted, Ta=25℃ and Vcc=5.0V) Typical value Parameter Symbol 02F 03F 06F/FS 07F Circuit current Maximum output level1 Maximum output level2 Maximum output level U Maximum output level D Unit V 09F 27FV Unit Icc 14.0 13.0 15.0 12.5 mA Clamp Vom1 ― 2.9 ― 2.9 VP-P Bias Vom2 3.1 ― ― 3.0 VP-P Pedestal clamp VomU ― 1.65 ― VP-P Pedestal clamp VomD ― 0.95 ― VP-P 0 dB dB dB 0.007 % Voltage gain Interchannel crosstalk Frequency characteristic Gv CT Gf Total harmonic distortion THD CTL pin switching level Clamp input level VTH Vct 0 -65 0 -1 ― 2.5 L≦0.75 H≧2.2 V V Conditions ― f=1kHz, THD=0.5%, with clamp f=1kHz, THD=0.5%, without clamp Dynamic range on positive side of clamp level Dynamic range on negative side of clamp level ｆ=1MHz, VIN＝1 VP-P ｆ=4.43MHz, VIN=1 VP-P 10MHz/1MHz, VIN= VP-P ｆ=1kHz, 1Vp-p, Bias type H: IN1 L: IN2 Only BA7606F/FS ●Cautions on use 1) Numbers and data in entries are representative design values and are not guaranteed values of the items. 2) Although we are confident in recommending the sample application circuits, carefully check their characteristics further when using them. When modifying externally attached component constants before use, determine them so that they have sufficient margins by taking into account variations in externally attached components and the Rohm LSI, not only for static characteristics but also including transient characteristics. 3) Absolute maximum ratings If applied voltage, operating temperature range, or other absolute maximum ratings are exceeded, the LSI may be damaged. Do not apply voltages or temperatures that exceed the absolute maximum ratings. If you think of a case in which absolute maximum ratings are exceeded, enforce fuses or other physical safety measures and investigate how not to apply the conditions under which absolute maximum ratings are exceeded to the LSI. 4) GND potential Make the GND pin voltage such that it is the lowest voltage even when operating below it. Actually confirm that the voltage of each pin does not become a lower voltage than the GND pin, including transient phenomena. 5) Thermal design Perform thermal design in which there are adequate margins by taking into account the allowable power dissipation in actual states of use. 6) Shorts between pins and misinstallation When mounting the LSI on a board, pay adequate attention to orientation and placement discrepancies of the LSI. If it is misinstalled and the power is turned on, the LSI may be damaged. It also may be damaged if it is shorted by a foreign substance coming between pins of the LSI or between a pin and a power supply or a pin and a GND. 7) Operation in strong magnetic fields Adequately evaluate use in a strong magnetic field, since there is a possibility of malfunction. 8) A bias input coupling capacitor on the order of 10 μF~33 μF is appropriate. 9) A clamp input coupling capacitor on the order of 0.1 μF~1 μF is appropriate. 10) Make the clamp pulse width of the BA7606F/FS at least 1 μs. 2/8 ●Block diagram Fig.1 BA7602F Fig.2 BA7603F Fig.3 BA7606F/FS Fig.4 BA7607F, BA7627FV CTL pin settings Fig.5 BA7609F 3/8 CTL OUTPUT Ｌ IN2 Ｈ IN1 ●Reference data Pin DC voltage（VCC=5V, Ta=25℃） Pin DC voltage (V) Pin No. BA7602F BA7603F BA7606F/FS BA7607F BA7627FV BA7609F 1 3.27 2.05 2.96 2.05 2.48 2 4.91 4.91 4.91 4.91 4.91 3 1.84 0.65 1.54 0.65 1.76 4 0 0 0 0 0 5 1.84 0.65 1.54 0.65 1.76 6 1.84 0.65 1.54 1.76 0.65 7 4.91 4.91 4.91 4.91 4.91 8 3.27 2.05 2.96 2.48 2.05 9 3.27 2.05 2.96 2.48 2.05 10 0 0 4.97 0 0 11 3.27 2.05 2.96 2.05 2.48 12 4.91 4.91 4.91 4.91 4.91 13 5.00 5.00 5.00 5.00 5.00 14 3.27 2.05 2.96 2.05 2.48 15 0 0 0 0 0 16 3.27 2.05 2.96 2.05 2.48 Input/Output impedance Limits (Typical) Parameter Input impedance Input impedance 02F 03F 06F/FS Bias 20k ― ― Clamp ― Output impedance 07F/27FV 20k 1.7M 30 30※ ※The 6pin output impedance in the BA7606F/FS is 130Ω. 4/8 09F Unit Ω Ω 30 Ω ●Measurement circuit 1/2 (BA7602F,BA7603F,BA7607F, BA7609F) Fig.6 BA7602F, BA7603F, BA7607F, BA7609F, BA7627FV 5/8 ●Measurement circuit 2/2 (BA7606F/FS) Input waveform Output waveform Fig.7 BA7606F/FS 6/8 ●Reference data BA7603F Vcc=5.0V BA7603F 0 Ta=25℃ Vcc=6.0V Ta=90℃ 10 5 Vcc=4.0V -2 -2.5 -2 5 6 -3 -3.5 -3.5 7 -4 0.1 1 0.1 100 1 BA7606F Vcc=5.0V, Ta=25℃ 10 FREQUENCY : f (MHz) Fig.10 Frequency characteristics vs. temperature Fig.9 Frequency characteristics vs. Supply voltage Fig.8 Circuit current vs. Supply voltage BA7606F 10 FREQUENCY : f (MHz) SUPPLY VOLTAGE : Vcc (V) 0 Ta=90℃ -2.5 -4 4 Ta=25℃ -1.5 -3 0 Ta=-30℃ -1 -1.5 GAIN (dB) Ta=25℃ 15 Vcc=5.0V -0.5 Vcc=5.0V -1 Ta=-30℃ 20 BA7603F 0 -0.5 25 GAIN : Gf (dB) CIRCUIT CURRENT : Icc (mA) 30 INPUT IN2a(1pin) f=1MHz,1Vpp Vcc=5.0V, Ta=25℃ BA7606F INPUT IN2a(1pin) f=1MHz,1Vpp Vcc=5.0V, Ta=25℃ -10 OUTa (3pin) 500mV/DIV GAIN (dB) -20 -30 -40 OUTa (3pin) 500mV/DIV -50 -60 CTLa (2pin) 2V/DIV 20nsec/DIV CTLa (2pin) 2V/DIV 20nsec/DIV -70 -80 0.1 0.2 0.3 0.5 2 1 3 5 10 FREQUENCY (MHz) Fig.13 Switching characteristics2 Fig.12 Switching characteristics1 Fig.11 Interchannel crosstalk ON→OFF OFF→ON ●Selection of order type B A 6 7 0 2 F E 2 Tape and Reel information E2 BA7602F E2 BA7603F E2 BA7606F/FS E2 BA7607F E2 BA7609F E2 BA7627FV Part. No BA7602F BA7603F BA7606F/FS BA7607F BA7609F BA7627FV SOP16 <Dimension> <Tape and Reel information> 0.3Min. 8 4.4±0.2 6.2±0.3 1 E2 (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand) 0.15±0.1 0.1 1234 1234 1234 1Pin 1234 1234 Reel (Unit:mm) 1234 0.4±0.1 1234 1.27 2500pcs 1234 0.11 1.5±0.1 9 Embossed carrier tape Direction of feed 10.0±0.2 16 Tape Quantity Direction of feed ※When you order , please order in times the amount of package quantity. 7/8 100 SSOP-A16 <Dimension> <Tape and Reel information> 1 8 2500pcs Direction of feed E2 (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand) 0.15±0.1 0.1 1234 1234 Direction of feed 1pin Reel 1234 1234 1234 1234 0.36±0.1 1234 0.8 0.3Min. 9 Embossed carrier tape Quantity 1234 6.2±0.3 1.5±0.1 4.4±0.2 0.11 6.6±0.2 16 Tape ※When you order , please order in times the amount of package quantity. （Unit:mm) SSOP-B16 <Dimension> <Tape and Reel information> 9 1 8 0.3Min. 16 Embossed carrier tape Quantity 2500pcs Direction of feed E2 (The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand) 0.15 ± 0.1 1234 1234 1234 1pin 1234 （Unit:mm) 1234 Reel 1234 1234 0.1 0.65 0.22 ± 0.1 1234 1.15 ± 0.1 6.4 ± 0.3 0.1 4.4 ± 0.2 5.0 ± 0.2 Tape Direction of feed ※When you order , please order in times the amount of package quantity. Catalog No.08T295A '08.8 ROHM © Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2008 ROHM CO.,LTD. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0