Single-Tap .040 x .040 Series Thin Film Single-Tap Chip Resistors (.040 x .040 Series) Chip resistors provide variations in resistor material, temperature coefficient of resistance, resistance and tolerance. Features Photo • • • Available Options Include: Chip Size: .040” x .040” Silicon Substrate Wire bond pads • Resistor Tolerance to 0.1% • Nickel Chrome or Tantalum Nitride Resistor Materials • TCR options available API Technologies thin film single-tapped chip resistors .040 x .040 series are available in a wide range of resistances and tolerances with values available from 500 kohms to 2.7 Mohm. The thin film resistor layer is made of NickelChromium or Tantalum Nitride (TaN), with a gold conductor layer. Applications for thin film center-tapped chip resistors include military and industrial hybrids, and medical, aerospace and communications equipment. Single-tapped chip resistors are available with either passivated nickel chrome or tantalum-nitride resistor metalization. • Nickel chrome provides excellent stability and temperature coefficient in hermetic applications • Tantalum-nitride provides superior moisture-resistance for non-hermetic applications. Electrical Specifications Parameter Power Rating Life Noise Limit 500 mW +/-0.2% max -35 dB typ Test conditions (70 C derated to 0 mW @ 150 C) 1000 hours @ 125 degrees C MIL-STD-202 method 308 High Temp Exposure +/-0.2% max 100 hours at 150 degrees C TCR (Nickel Chrome) +/-50 ppm/C -55 to 125 degrees C TCR (Tantalum Nitride) +/-125 ppm/C -55 to 125 degrees C Operating voltage 100 VDC max Moisture resistance +/-0.5% max MIL-STD-202 method 106 Thermal shock +/-0.5% max MIL-STD-202 method 107 Rev Date: 6/10/2014 © API Technologies Corp. Proprietary Information Page # 1 | www.apitech.com | micro.apitech.com | +1.888.553.7531 | [email protected] Single-Tap .040 x .040 Series Mechanical Specifications Substrate Silicon with thermal oxide Bond pad metalization Bondable Gold Size .041 x .041 +/-.002 (0.78 x 0.78 mm +/- .05mm) Thickness .012 +/-.003 “ Bond pad dimensions .004 x .004 minimum (0.1 x 0.1 mm) Protective overcoat (passivation) Silox glass on NiCr versions only Back side Lapped silicon Typical Configuration Packaging Options • Waffle Pack (400 resistors per pack) - standard • Waffle Pack (50 resistors per pack) • Waffle Pack (100 resistors per pack) • Tape and reel Rev Date: 6/10/2014 © API Technologies Corp. Proprietary Information Page # 2 | www.apitech.com | micro.apitech.com | +1.888.553.7531 | [email protected] Single-Tap .040 x .040 Series Ordering Information All parts are 100% electrically tested, sample tested per MIL-STD-38534 section 3.4, and visually inspected to MIL-STD883 requirements. Chips are supplied in standard 2”x 2” matrix tray packaging. Base part code Ohm value (total of both halves) Tolerance letter 69AL- (NiCr on Silicon) NNNE X 69ALT- (TaN on Silicon) NNNE X Availability • 69AL series is available from 1 Mohm to 2.7 Mohm • 69 ALT series is available from 500 kohms to 1.3 Mohm Ordering Examples • 69AL-1004J is a 1 megohm 5% resistor with nichrome metalization. Part Number Breakout/Designation Base Code Type 69AL 69ALT NNNE X Value Tolerance B=0.1% C=0.25% D=0.5% F=1% G=2% J=5% K=10% L=15% M=20% NNN = Value E = Exponent YY Special TCR Code (optional) T2=±25ppm* T5 =±50ppm* T6=0 to -50 ppm* T7=0 to 50 ppm* *69AL Series Only Rev Date: 6/10/2014 © API Technologies Corp. Proprietary Information Page # 3 | www.apitech.com | micro.apitech.com | +1.888.553.7531 | [email protected] Single-Tap .040 x .040 Series Bonding Areas Bonding Areas and Dimensions Factory Information API Technologies, 400 Nickerson Road, Marlborough, MA 01752 TEL: 508-251-6400 FAX: 508-251-6401 http://micro.apitech.com/thin_film.aspx Rev Date: 6/10/2014 © API Technologies Corp. Proprietary Information Page # 4 | www.apitech.com | micro.apitech.com | +1.888.553.7531 | [email protected]