IDT74LVC2244A 3.3V CMOS OCTAL BUFFER/DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE 3.3V CMOS OCTAL BUFFER/DRIVER WITH 3STATE OUTPUTS AND 5 VOLT TOLERANT I/O FEATURES: IDT74LVC2244A DESCRIPTION: • 0.5 MICRON CMOS Technology • ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) • VCC = 3.3V ± 0.3V, Normal Range • VCC = 2.7V to 3.6V, Extended Range µ W typ. static) • CMOS power levels (0.4µ • Rail-to-rail output swing for increased noise margin • All inputs, outputs, and I/O are 5V tolerant • Available in SOIC, SSOP, QSOP, and TSSOP packages This octal buffer/driver is built using advanced dual metal CMOS technology. The LVC2244A device is organized as two 4-bit line drivers with separate output-enable (OE) inputs. When OE is low, the device passes data from the A inputs to the Y outputs. When OE is high, the outputs are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE should be tied to Vcc through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. The LVC2244A has series resistors in the device output structure which will significantly reduce line noise when used with light loads. This driver has been designed to drive ±12mA at the designated threshold levels. Inputs can be driven from either 3.3V or 5V devices. This feature allows the use of this device as a translator in a mixed 3.3V/5V system environment. DRIVE FEATURES: • Balanced Output Drivers: ±12mA • Low switching noise APPLICATIONS: • 5V and 3.3V mixed voltage systems • Data communication and telecommunication systems FUNCTIONAL BLOCK DIAGRAM 1OE 1A1 1A2 1A3 1A4 1 2OE 2 18 4 16 6 14 8 12 1Y1 2A1 1Y2 2A2 1Y3 2A3 1Y4 2A4 19 11 9 13 7 15 5 17 3 2Y1 2Y2 2Y3 2Y4 The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE FEBRUARY 2000 1 © 2000 Integrated Device Technology, Inc. DSC-4644/1 IDT74LVC2244A 3.3V CMOS OCTAL BUFFER/DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION Symbol Description Max Unit VTERM Terminal Voltage with Respect to GND –0.5 to +6.5 V TSTG Storage Temperature –65 to +150 °C –50 to +50 mA 1OE 1 20 VCC IOUT DC Output Current 1A1 2 19 2OE IIK IOK Continuous Clamp Current, VI < 0 or VO < 0 –50 mA 2Y4 3 18 1Y1 ICC ISS Continuous Current through each VCC or GND ±100 mA 1A2 4 17 2A4 2Y3 5 16 1Y2 1A3 6 15 2A3 2Y2 7 14 1Y3 1A4 8 13 2A2 2Y1 9 12 1Y4 10 11 2A1 GND NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. CAPACITANCE (TA = +25°C, F = 1.0MHz) Parameter(1) Symbol Conditions Typ. Max. CIN Input Capacitance VIN = 0V 4.5 6 pF COUT Output Capacitance VOUT = 0V 5.5 8 pF CI/O I/O Port Capacitance VIN = 0V 6.5 8 pF NOTE: 1. As applicable to the device type. SOIC/ SSOP/ QSOP/ TSSOP TOP VIEW PIN DESCRIPTION Pin Names Description xOE Output Enable Inputs xAx Data Inputs xYx 3-State Outputs FUNCTION TABLE (EACH BUFFER)(1) Inputs Outputs xOE xAx xYx L H H L L L H X Z NOTE: 1. H = HIGH Voltage Level X = Don’t Care L = LOW Voltage Level Z = High-Impedance 2 Unit IDT74LVC2244A 3.3V CMOS OCTAL BUFFER/DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Operating Condition: TA = –40°C to +85°C Symbol VIH VIL Min. Typ.(1) Max. Unit VCC = 2.3V to 2.7V 1.7 — — V VCC = 2.7V to 3.6V 2 — — VCC = 2.3V to 2.7V — — 0.7 VCC = 2.7V to 3.6V — — 0.8 Parameter Input HIGH Voltage Level Input LOW Voltage Level Test Conditions V Input Leakage Current VCC = 3.6V VI = 0 to 5.5V — — ±5 µA IOZH High Impedance Output Current VCC = 3.6V VO = 0 to 5.5V — — ±10 µA IOZL (3-State Output pins) IOFF Input/Output Power Off Leakage VCC = 0V, VIN or VO ≤ 5.5V — — ±50 µA VIK Clamp Diode Voltage VCC = 2.3V, IIN = –18mA — –0.7 –1.2 V VH ICCL ICCH ICCZ ∆ICC Input Hysteresis Quiescent Power Supply Current VCC = 3.3V VCC = 3.6V VIN = GND or VCC — — 100 — — 10 mV µA 3.6 ≤ VIN ≤ 5.5V(2) One input at VCC - 0.6V, other inputs at VCC or GND — — — — 10 500 µA IIH IIL Quiescent Power Supply Current Variation NOTES: 1. Typical values are at VCC = 3.3V, +25°C ambient. 2. This applies in the disabled state only. OUTPUT DRIVE CHARACTERISTICS Symbol VOH Test Conditions(1) Parameter Output HIGH Voltage Unit V IOH = – 0.1mA VCC – 0.2 — VCC = 2.3V IOH = – 4mA 1.9 — IOH = – 6mA 1.7 — VCC = 3V Output LOW Voltage Max. VCC = 2.3V to 3.6V VCC = 2.7V VOL Min. VCC = 2.3V to 3.6V VCC = 2.3V VCC = 2.7V VCC = 3V IOH = – 4mA 2.2 — IOH = – 8mA 2 — IOH = – 6mA 2.4 — IOH = – 12mA 2 — IOL = 0.1mA — 0.2 IOL = 4mA — 0.4 IOL = 6mA — 0.55 IOL = 4mA — 0.4 IOL = 8mA — 0.6 IOL = 6mA — 0.55 IOL = 12mA — 0.8 V NOTE: 1. VIH and VIL must be within the min. or max. range shown in the DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE table for the appropriate VCC range. TA = – 40°C to + 85°C. 3 IDT74LVC2244A 3.3V CMOS OCTAL BUFFER/DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE OPERATING CHARACTERISTICS, VCC = 3.3V ± 0.3V, TA = 25°C Symbol Parameter CPD Power Dissipation Capacitance per Buffer/Driver Outputs enabled CPD Power Dissipation Capacitance per Buffer/Driver Outputs disabled Test Conditions Typical Unit CL = 0pF, f = 10Mhz 46 pF 2 SWITCHING CHARACTERISTICS(1) VCC = 2.7V Symbol VCC = 3.3V ± 0.3V Parameter Min. Max. Min. Max. Unit tPLH Propagation Delay — 6.4 1.5 5.5 ns tPHL xAx to xYx tPZH Output Enable Time — 8.1 1 7.1 ns tPZL xOE to xYx tPHZ Output Disable Time — 7.3 1.5 6.8 ns tPLZ xOE to xYx tSK(o) Output Skew(2) — — — 500 ps NOTES: 1. See TEST CIRCUITS AND WAVEFORMS. TA = – 40°C to + 85°C. 2. Skew between any two outputs of the same package and switching in the same direction. 4 IDT74LVC2244A 3.3V CMOS OCTAL BUFFER/DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS TEST CONDITIONS Symbol VCC(1)= 3.3V±0.3V VCC(1)= 2.7V VCC(2)= 2.5V±0.2V Unit VLOAD 6 6 2 x Vcc V VIH 2.7 2.7 Vcc V VT 1.5 1.5 Vcc / 2 V VLZ 300 300 150 mV VHZ 300 300 150 mV CL 50 50 30 pF VIN Pulse (1, 2) Generator GND tPZL OUTPUT SWITCH NORMALLY VLOAD LOW tPZH OUTPUT SWITCH NORMALLY GND HIGH 500Ω LVC Link Switch DATA INPUT VLOAD TIMING INPUT Disable High Enable High GND ASYNCHRONOUS CONTROL All Other Tests Open SYNCHRONOUS CONTROL VIH VT 0V tPHL1 tSK (x) tSK (x) VOH VOH-VHZ 0V VT 0V tSU VIH VT 0V VIH VT 0V VIH VT 0V VIH VT 0V tH tREM tSU tH Set-up, Hold, and Release Times VOH VT VOL LOW-HIGH-LOW PULSE VT tW HIGH-LOW-HIGH PULSE tPHL2 VT Pulse Width tSK(x) = tPLH2 - tPLH1 or tPHL2 - tPHL1 Output Skew - tSK(X) tPHZ LVC Link VOH VT VOL OUTPUT 2 VLOAD/2 VOL+VLZ VOL Enable and Disable Times SWITCH POSITION Open Drain Disable Low Enable Low tPLZ VLOAD/2 VT NOTE: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. NOTES: 1. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2.5ns; tR ≤ 2.5ns. 2. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2ns; tR ≤ 2ns. Test VIH VT 0V LVC Link DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. tPLH2 DISABLE ENABLE Test Circuit for All Outputs OUTPUT 1 VIH VT 0V CONTROL INPUT CL tPLH1 tPHL Propagation Delay D.U.T. INPUT tPLH LVC Link VOUT RT tPHL OPPOSITE PHASE INPUT TRANSITION Open 500Ω tPLH OUTPUT VLOAD VCC VIH VT 0V VOH VT VOL SAME PHASE INPUT TRANSITION LVC Link NOTES: 1. For tSK(o) OUTPUT1 and OUTPUT2 are any two outputs. 2. For tSK(b) OUTPUT1 and OUTPUT2 are in the same bank. 5 LVC Link IDT74LVC2244A 3.3V CMOS OCTAL BUFFER/DRIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION X LVC IDT XX Temp. Range Bus-Hold XX XXXX Device Type Package CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 SO PY Q PG Small Outline IC (gull wing) Shrink Small Outline Package Quarter Size Small Outline Package Thin Shrink Small Outline Package 2244A Octal Buffer/Driver with 3-State Outputs, ±12mA Blank No Bus-hold 74 –40°C to +85°C for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 6 for Tech Support: [email protected] (408) 654-6459