IDTQS74FCT2828AT/BT HIGH-SPEED CMOS BUS INTERFACE 10-BIT BUFFERS INDUSTRIAL TEMPERATURE RANGE HIGH-SPEED CMOS BUS INTERFACE 10-BIT BUFFER IDTQS74FCT2828AT/BT DESCRIPTION: FEATURES: The IDTQS74FCT2828T is a 10-bit buffer with 3-state outputs and a 25Ω resistor, useful for driving transmission lines and reducing system noise. The 2828T series parts can replace the 828T series to reduce noise in an existing design. All inputs have clamp diodes for undershoot noise suppression. All outputs have ground bounce suppression. Outputs will not load an active bus when Vcc is removed from the device. • • • • • • CMOS power levels: <7.5mW static Undershoot clamp diodes on all outputs True TTL input and output compatibility Ground bounce controlled outputs Reduced output swing of 0 to 3.5V Ω series resistor outputs reduce reflection and other Built-in 25Ω system noise • A and B speed grades with 5ns tPD for B • IOL = 12mA • Available in QSOP package FUNCTIONAL BLOCK DIAGRAM Dx Yx 25Ω OE1 OE2 INDUSTRIAL TEMPERATURE RANGE MARCH 2002 1 c 2002 Integrated Device Technology, Inc. DSC-5259/5 IDTQS74FCT2828AT/BT HIGH-SPEED CMOS BUS INTERFACE 10-BIT BUFFERS INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION Symbol OE1 1 24 VCC D0 2 23 Y0 Description Max Unit VTERM Terminal Voltage with Respect to GND –0.5 to +7 V TSTG Storage Temperature –65 to +150 °C IOUT DC Output Current Max Sink Current/Pin 120 mA IIK Input Diode Current, VIN < 0 –20 mA IOK Output Diode Current, VOUT < 0 –50 mA D1 3 22 Y1 D2 4 21 Y2 D3 5 20 Y3 D4 6 19 Y4 D5 7 18 Y5 D6 8 17 Y6 D7 9 16 Y7 D8 10 15 Y8 Symbol Conditions Typ. Max. Unit CIN Input Capacitance VIN = 0V 8 — pF D9 11 14 Y9 COUT Output Capacitance VOUT = 0V 8 — pF GND 12 13 OE2 NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. CAPACITANCE (TA = +25°C, F = 1.0MHz) Parameter(1) NOTE: 1. This parameter is measured at characterization but not tested. QSOP TOP VIEW PIN DESCRIPTION Pin Names I/O Description Dx I Data Inputs Yx O Data Outputs OEx I Output Enables FUNCTION TABLE(1) Inputs OE1 OE2 Dx Yx Function L L L H Enabled L L H L Enabled H — — Z High-Impedance — H — Z High-Impedance NOTE: 1. H = HIGH L = LOW Z = High-Impedance 2 Outputs IDTQS74FCT2828AT/BT HIGH-SPEED CMOS BUS INTERFACE 10-BIT BUFFERS INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = –40°C to +85°C, VCC = 5.0V ±5% Symbol Parameter Test Conditions Min. Typ.(1) Max. Unit — — V VIH Input HIGH Level Guaranteed Logic HIGH Level 2 VIL Input LOW Level Guaranteed Logic LOW Level — — 0.8 V ∆VT Input Hysteresis VTLH - VTHL for all inputs — 0.2 — V IIH Input HIGH Current VCC = Max. 0 ≤ VIN ≤ VCC — — ±5 µA IIL Input LOW Current IOZ Off-State Output Current (Hi-Z) 0 ≤ VIN ≤ VCC — — ±5 µA VCC = Max 2.0V(2) IOR VIC Current Drive Input Clamp Voltage VCC = Max., VOUT = VCC = Min, IIN = -18mA , TA = 25°C(2) 50 — — –0.7 — –1.2 mA V VOH VOL ROUT(3) Output HIGH Voltage Output LOW Voltage Output Resistance VCC = Min. VCC = Min. VCC = Min. 2.4 — 18 — — 25 — 0.5 40 V V Ω IOH = -15mA IOL = 12mA IOH = -12mA NOTES: 1. Typical values are at VCC = 5.0V, TA = 25°C. 2. This parameter is measured at characterization but not tested. 3. ROUT changed on March 8, 2002. See rear page for more information. POWER SUPPLY CHARACTERISTICS Following Conditions Apply Unless Otherwise Specified: Industrial: TA = -40°C to +85°C, VCC = 5.0V ± 5% Symbol ICC Parameter Quiescent Power Supply Current ∆ICC Supply Current per Input TTL Inputs HIGH ICCD Supply Current per Input per MHz Test Conditions(1) VCC = Max. freq = 0 0V ≤ VIN ≤ 0.2V or VCC - 0.2V ≤ VIN ≤ Vcc VCC = Max. VIN = 3.4V(2) freq = 0 VCC = Max. Outputs Open and Enabled One Bit Toggling 50% Duty Cycle Other inputs at GND or Vcc(3,4) Min. — Max. 1.5 Unit mA — 2 mA — 0.25 mA/MHz NOTES: 1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics. 2. Per TLL driven input (VIN = 3.4V). 3. For flip-flops, ICCD is measured by switching one of the data input pins so that the output changes every clock cycle. This is a measurement of device power consumption only and does not include power to drive load capacitance or tester capacitance. 4. IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ∆ICC DHNT + ICCD (fCP/2 + fiNi) ICC = Quiescent Current ∆ICC = Power Supply Current for a TTL High Input (VIN = 3.4V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current Caused by an Output Transition Pair (HLH or LHL) fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices) fi = Input Frequency Ni = Number of Inputs at fi All currents are in milliamps and all frequencies are in megahertz. 3 IDTQS74FCT2828AT/BT HIGH-SPEED CMOS BUS INTERFACE 10-BIT BUFFERS INDUSTRIAL TEMPERATURE RANGE SWITCHING CHARACTERISTICS OVER OPERATING RANGE(1) FCT2828AT Symbol tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ Parameter(2) Propagation Delay Dx to Yx Propagation Delay Dx to Yx(2,3) Output Enable Time OEx to Yx Output Enable Time OEx to Yx(2,3) Output Disable Time OEx to Yx(2,4) Output Disable Time OEx to Yx(2) NOTES: 1. CLOAD = 50pF, RLOAD = 500Ω unless otherwise noted. 2. This parameter is guaranteed by design but not tested. 3. CLOAD = 300pF. 4. CLOAD = 5pF. 4 FCT2828BT Min. Max. — 5 Min. — Max. 7.5 Unit ns — 17 — 14 ns — 12 — 8 ns — 23 — 18 ns — 9 — 6 ns — 10 — 7 ns IDTQS74FCT2828AT/BT HIGH-SPEED CMOS BUS INTERFACE 10-BIT BUFFERS INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS VCC 7.0V SWITCH POSITION 500W Pulse Generator VOUT VIN D.U.T. 50pF RT 500W CL Test Switch Open Drain Disable Low Enable Low Closed All Other Tests Open DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. FCTL link Test Circuits for All Outputs DATA INPUT tH tSU TIMING INPUT ASYNCHRONOUS CONTROL PRESET CLEAR ETC. SYNCHRONOUS CONTROL PRESET CLEAR CLOCK ENABLE ETC. 3V 1.5V 0V 3V 1.5V 0V tREM tSU LOW-HIGH-LOW PULSE 1.5V tW 3V 1.5V 0V HIGH-LOW-HIGH PULSE 1.5V 3V 1.5V 0V tH FCTL link Pulse Width FCTL link Set-Up, Hold, and Release Times ENABLE SAME PHASE INPUT TRANSITION tPLH tPHL OUTPUT tPLH OPPOSITE PHASE INPUT TRANSITION tPHL 3V 1.5V 0V DISABLE 3V 1.5V 0V CONTROL INPUT tPLZ tPZL VOH 1.5V VOL OUTPUT NORMALLY LOW 3V 1.5V 0V OUTPUT NORMALLY HIGH FCTL link SWITCH CLOSED tPZH SWITCH OPEN 3.5V 1.5V 3.5V 0.3V VOL tPHZ 0.3V 1.5V 0V VOH 0V FCTL link Propagation Delay Enable and Disable Times NOTES: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. 2. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2.5ns; tR ≤ 2.5ns. 5 IDTQS74FCT2828AT/BT HIGH-SPEED CMOS BUS INTERFACE 10-BIT BUFFERS INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION IDTQS FCT XX XX XXXX Device Type Package Temp. Range Q Quarter Size Small Outline Package 2828AT High-Speed CMOS Bus Interface 10-Bit Buffer 2828BT 74 –40°C to +85°C As per PCN L0201-02, the Output Resistance (ROUT) specifications have changed as of March 8, 2002. The original specifications were: Parameter ROUT Description Min. Typ. Max. Unit VCC = Min, IOL = -15mA 20 28 40 Ω CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 6 for Tech Support: [email protected] (408) 654-6459