AD AD8222HBCPZ-R7

Precision, Dual-Channel
Instrumentation Amplifier
AD8222
APPLICATIONS
Multichannel data acquisition for
ECG and medical instrumentation
Industrial process controls
Wheatstone bridge sensors
Differential drives for
High resolution input ADCs
Remote sensors
+VS
OUT1
OUT2
–VS
FUNCTIONAL BLOCK DIAGRAM
16
15
14
13
AD8222
–IN2
2
11
RG2
RG1
3
10
RG2
+IN1
4
9
+IN2
5
6
7
8
05947-001
12
RG1
–VS
1
REF2
–IN1
+VS
Two channels in small 4 mm × 4 mm LFCSP
Gain set with 1 resistor per amplifier (G = 1 to 10,000)
Low noise
8 nV/√Hz at 1 kHz
0.25 μV p-p (0.1 Hz to 10 Hz)
High accuracy dc performance (B grade)
60 μV maximum input offset voltage
0.3 μV/°C maximum input offset drift
1.0 nA maximum input bias current
126 dB minimum CMRR (G = 100)
Excellent ac performance
140 kHz bandwidth (G = 100)
13 μs settling time to 0.001%
Differential output option (single channel)
Fully specified
Adjustable common-mode output
Supply range: ±2.3 V to ±18 V
REF1
FEATURES
Figure 1. 4 mm × 4 mm LFCSP
Table 1. Instrumentation Amplifiers by Category1
General
Purpose
AD8220
AD8221
AD8222
AD8224
AD8228
AD8295
1
Zero
Drift
AD8231
AD8290
AD8293
AD8553
AD8556
AD8557
Military
Grade
AD620
AD621
AD524
AD526
AD624
Low
Power
AD8235
AD8236
AD627
AD623
AD8223
AD8226
AD8227
High Speed
PGA
AD8250
AD8251
AD8253
See www.analog.com for the latest selection of instrumentation amplifiers.
GENERAL DESCRIPTION
The AD8222 is a dual-channel, high performance instrumentation
amplifier that requires only one external resistor per amplifier
to set gains of 1 to 10,000.
The AD8222 is the first dual-instrumentation amplifier in the
small 4 mm × 4mm LFCSP. It requires the same board area as a
typical single instrumentation amplifier. The smaller package
allows a 2× increase in channel density and a lower cost per
channel, all with no compromise in performance.
The AD8222 can also be configured as a single-channel, differential output instrumentation amplifier. Differential outputs provide
high noise immunity, which can be useful when the output
signal must travel through a noisy environment, such as with
remote sensors. The configuration can also be used to drive
differential input ADCs.
The AD8222 maintains a minimum CMRR of 80 dB to 4 kHz
for all grades at G = 1. High CMRR over frequency allows the
AD8222 to reject wideband interference and line harmonics,
greatly simplifying filter requirements. The AD8222 also has a
typical CMRR drift over temperature of just 0.07 μV/V/°C at G = 1.
The AD8222 operates on both single and dual supplies and only
requires 2.2 mA maximum supply current for both amplifiers.
It is specified over the industrial temperature range of −40°C to
+85°C and is fully RoHS compliant.
For a single-channel version, see the AD8221.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2006–2010 Analog Devices, Inc. All rights reserved.
AD8222
TABLE OF CONTENTS
Features .............................................................................................. 1 Package Considerations ............................................................. 16 Applications ....................................................................................... 1 Layout .......................................................................................... 16 Functional Block Diagram .............................................................. 1 Input Bias Current Return Path ............................................... 17 General Description ......................................................................... 1 Input Protection ......................................................................... 18 Revision History ............................................................................... 2 RF Interference ........................................................................... 18 Specifications..................................................................................... 3 Common-Mode Input Voltage Range ..................................... 18 Absolute Maximum Ratings............................................................ 6 Applications Information .............................................................. 19 Thermal Resistance ...................................................................... 6 Differential Output .................................................................... 19 ESD Caution .................................................................................. 6 Driving a Differential Input ADC ............................................ 20 Pin Configuration and Function Descriptions ............................. 7 Precision Strain Gage ................................................................. 20 Typical Performance Characteristics ............................................. 8 Driving Cabling .......................................................................... 21 Theory of Operation ...................................................................... 15 Outline Dimensions ....................................................................... 22 Amplifier Architecture .............................................................. 15 Ordering Guide .......................................................................... 23 Gain Selection ............................................................................. 15 Reference Terminal .................................................................... 16 REVISION HISTORY
2/10—Rev. 0 to Rev. A
Added LFCSP_VQ, CP-16-13 Package ............................ Universal
Changes to Features Section and Table 1 ...................................... 1
Changed VIN+ to V+IN, VIN− to V−IN, and T to TA Throughout ..... 3
Change to Reference Input Parameter, Table 2 ............................. 4
Changed Output Short-Circuit Current to Output Short-Circuit
Duration, Table 5 .............................................................................. 6
Changes to Thermal Resistance Section and Table 6................... 6
Changes to Figure 2 .......................................................................... 7
Changes to Figure 19 ...................................................................... 10
Changes to Figure 43 ...................................................................... 14
Changes to Reference Terminal Section, Figure 45, and Package
Considerations Section .................................................................. 16
Deleted Thermal Pad Section ....................................................... 16
Added Package Without Thermal Pad and Package with
Thermal Pad Sections .................................................................... 16
Changes to Figure 46...................................................................... 17
Deleted Solder Wash Section ........................................................ 17
Changes to RFI and Antialising Filter Section ........................... 20
Updated Outline Dimensions ....................................................... 22
Changes to Ordering Guide .......................................................... 23
7/06—Revision 0: Initial Version
Rev. A | Page 2 of 24
AD8222
SPECIFICATIONS
VS = ±15 V, VREF = 0 V, TA = 25°C, G = 1, RL = 2 kΩ, unless otherwise noted.
Table 2. Single-Ended and Differential1 Output Configuration
Parameter
COMMON-MODE REJECTION
RATIO (CMRR)
CMRR DC to 60 Hz
G=1
G = 10
G = 100
G = 1000
CMRR at 4 kHz
G=1
G = 10
G = 100
G = 1000
CMRR Drift
NOISE
Voltage Noise, 1 kHz
Input Voltage Noise, eNI
Output Voltage Noise, eNO
RTI
G=1
G = 10
G = 100 to 1000
Current Noise
VOLTAGE OFFSET
Input Offset, VOSI
Over Temperature
Average TC
Output Offset, VOSO
Over Temperature
Average TC
Offset RTI vs. Supply (PSR)
G=1
G = 10
G = 100
G = 1000
INPUT CURRENT (PER CHANNEL)
Input Bias Current, IBIAS
Over Temperature
Average TC
Input Offset Current, IOFFSET
Over Temperature
Average TC
Conditions
VCM = –10 V to +10 V
Min
A Grade
Typ
Max
Min
B Grade
Typ
Max
Unit
1 kΩ source imbalance
80
100
120
130
86
106
126
140
dB
dB
dB
dB
80
90
100
100
80
100
110
110
dB
dB
dB
dB
μV/V/°C
TA = −40°C to +85°C, G = 1
0.07
RTI noise = √(eNI2 + (eNO/G)2)
V+IN, V−IN, VREF = 0 V
V+IN, V−IN, VREF = 0 V
f = 0.1 Hz to 10 Hz
0.07
8
75
8
75
2
0.5
0.25
40
6
f = 1 kHz
f = 0.1 Hz to 10 Hz
RTI VOS = (VOSI) + (VOSO/G)
VS = ±5 V to ±15 V
TA = −40°C to +85°C
2
0.5
0.25
40
6
120
150
0.4
500
0.8
9
VS = ±5 V to ±15 V
TA = −40°C to +85°C
nV/√Hz
nV/√Hz
μV p-p
μV p-p
μV p-p
fA/√Hz
pA p-p
60
80
0.3
350
0.5
5
μV
μV
μV/°C
μV
mV
μV/°C
VS = ±2.3 V to ±18 V
90
110
124
130
110
120
130
140
0.5
TA = −40°C to +85°C
1
0.2
TA = −40°C to +85°C
1
Rev. A | Page 3 of 24
94
114
130
140
2.0
3.0
1
1.5
110
130
140
150
0.2
1
0.1
0.5
dB
dB
dB
dB
1.0
1.5
0.5
0.6
2
nA
nA
pA/°C
nA
nA
pA/°C
AD8222
Parameter
REFERENCE INPUT
RIN
IIN
Voltage Range
Reference Gain to Output
Reference Gain Error
GAIN
Gain Range
Gain Error
G=1
G = 10
G = 100
G = 1000
Gain Nonlinearity
G=1
G = 10
G = 100
Gain vs. Temperature
G=1
G > 12
INPUT
Input Impedance
Differential
Common Mode
Input Operating Voltage Range3
Over Temperature
Input Operating Voltage Range3
Over Temperature
OUTPUT
Output Swing
Over Temperature
Output Swing
Over Temperature
Short-Circuit Current
POWER SUPPLY
Operating Range
Quiescent Current (per Amplifier)
Over Temperature
TEMPERATURE RANGE
Specified Performance
Operational4
Conditions
Min
A Grade
Typ
Max
20
50
V+IN, V−IN, VREF = 0 V
−VS
60
+VS
Min
B Grade
Typ
Max
20
50
−VS
1
0.01
60
+VS
1
0.01
Unit
kΩ
μA
V
V/V
%
G = 1 + (49.4 kΩ/RG)
1
10000
1
10000
V/V
0.02
0.15
0.15
0.15
%
%
%
%
VOUT ± 10 V
0.05
0.3
0.3
0.3
VOUT = –10 V to +10 V
3
7
7
10
20
20
1
7
7
5
20
20
ppm
ppm
ppm
3
10
−50
2
5
−50
ppm/°C
ppm/°C
GΩ||pF
GΩ||pF
V
V
V
V
100||2
100||2
VS = ±2.3 V to ±5 V
TA = −40°C to +85°C
VS = ±5 V to ±18 V
TA = −40°C to +85°C
RL = 10 kΩ
VS = ±2.3 V to ±5 V
TA = −40°C to +85°C
VS = ±5 V to ±18 V
TA = −40°C to +85°C
100||2
100||2
−VS + 1.9
−VS + 2.0
−VS + 1.9
−VS + 2.0
+VS − 1.1
+VS − 1.2
+VS − 1.2
+VS − 1.2
−VS + 1.9
−VS + 2.0
−VS + 1.9
−VS + 2.0
+VS − 1.1
+VS − 1.2
+VS − 1.2
+VS − 1.2
−VS + 1.1
−VS + 1.4
−VS + 1.2
−VS + 1.6
+VS − 1.2
+VS − 1.3
+VS − 1.4
+VS − 1.5
−VS + 1.1
−VS + 1.4
−VS + 1.2
−VS + 1.6
+VS − 1.2
+VS − 1.3
+VS − 1.4
+VS − 1.5
V
V
V
V
mA
±18
1.1
1.2
V
mA
mA
+85
+125
°C
°C
18
VS = ±2.3 V to ±18 V
±2.3
0.9
1
TA = −40°C to +85°C
−40
−40
1
Refers to differential configuration shown in Figure 49.
Does not include the effects of external resistor, RG.
3
One input grounded. G = 1.
4
See the Typical Performance Characteristics section for expected operation between 85°C and 125°C.
2
Rev. A | Page 4 of 24
18
±18
1.1
1.2
±2.3
+85
+125
−40
−40
0.9
1
AD8222
VS = ±15 V, VREF = 0 V, TA = 25°C, RL = 2 kΩ, unless otherwise noted.
Table 3. Single-Ended Output Configuration—Dynamic Performance (Both Amplifiers)
Parameter
DYNAMIC RESPONSE
Small Signal −3 dB Bandwidth
G=1
G = 10
G = 100
G = 1000
Settling Time 0.01%
G = 1 to 100
G = 1000
Settling Time 0.001%
G = 1 to 100
G = 1000
Slew Rate
Conditions
Min
A Grade
Typ
Max
Min
B Grade
Typ
Max
Unit
1200
750
140
15
1200
750
140
15
kHz
kHz
kHz
kHz
10
80
10
80
μs
μs
13
110
2
2.5
1.5
2
13
110
2
2.5
μs
μs
V/μs
V/μs
A Grade
Typ
Max
Min
B Grade
Typ
10 V step
10 V step
G=1
G = 5 to 1000
1.5
2
Table 4. Differential Output Configuration1—Dynamic Performance
Parameter
DYNAMIC RESPONSE
Small Signal −3 dB Bandwidth
G=1
G = 10
G = 100
G =1000
Settling Time 0.01%
G = 1 to 100
G = 1000
Settling Time 0.001%
G = 1 to 100
G = 1000
Slew Rate
1
Conditions
Min
Max
Unit
1000
650
140
15
1000
650
140
15
kHz
kHz
kHz
kHz
15
80
15
80
μs
μs
18
110
2
2.5
18
110
2
2.5
μs
μs
V/μs
V/μs
10 V step
10 V step
G=1
G = 5 to 1000
1.5
2
Refers to differential configuration shown in Figure 49.
Rev. A | Page 5 of 24
1.5
2
AD8222
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 5.
Parameter
Supply Voltage
Output Short-Circuit Current Duration
Input Voltage (Common Mode)
Differential Input Voltage
Storage Temperature Range
Operational Temperature Range
Package Glass Transition Temperature (TG)
ESD
Human Body Model
Charge Device Model
Rating
±18 V
Indefinite
±VS
±VS
−65°C to +130°C
−40°C to +125°C
130°C
1 kV
1 kV
Table 6.
Package
CP-16-19: LFCSP Without Thermal Pad
CP-16-13: LFCSP with Thermal Pad
θJA
86
48
Unit
°C/W
°C/W
The θJA values in Table 6 assume a 4-layer JEDEC standard
board. For the LFCSP with thermal pad, it is assumed that the
thermal pad is soldered to a landing on the PCB board, with the
landing thermally connected to a heat dissipating power plane.
θJC at the exposed pad is 4.4°C/W.
Maximum Power Dissipation
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions may affect device reliability.
The maximum safe power dissipation for the AD8222 is limited
by the associated rise in junction temperature (TJ) on the die. At
approximately 130C, which is the glass transition temperature,
the plastic changes its properties. Even temporarily exceeding
this temperature limit may change the stresses that the package
exerts on the die, permanently shifting the parametric performance
of the amplifiers. Exceeding a temperature of 130°C for an
extended period can result in a loss of functionality.
ESD CAUTION
Rev. A | Page 6 of 24
AD8222
PIN 1
INDICATOR
11 RG2
10 RG2
9 +IN2
–VS 8
TOP VIEW
+VS 5
+IN1 4
AD8222
REF1 6
REF2 7
RG1 3
12 –IN2
NOTES
1. THE AD8222 COMES IN TWO PACKAGE TYPES—EACH A 16 LEAD
4mm × 4mm LFCSP. ONE PACKAGE TYPE HAS AN EXPOSED
THERMAL PAD, WHICH IS CONNECTED TO –VS. THE OTHER
PACKAGE TYPE DOES NOT EXPOSE THE THERMAL PAD. SEE THE
PACKAGE CONSIDERATIONS SECTION FOR MORE INFORMATION.
Figure 2. Pin Configuration
Table 7. Pin Function Descriptions
Pin No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Mnemonic
−IN1
RG1
RG1
+IN1
+VS
REF1
REF2
−VS
+IN2
RG2
RG2
−IN2
−VS
OUT2
OUT1
+VS
Description
Negative Input In-Amp 1
Gain Resistor In-Amp 1
Gain Resistor In-Amp 1
Positive Input In-Amp 1
Positive Supply
Reference Adjust In-Amp 1
Reference Adjust In-Amp 2
Negative Supply
Positive Input In-Amp 2
Gain Resistor In-Amp 2
Gain Resistor In-Amp 2
Negative Input In-Amp 2
Negative Supply
Output In-Amp 2
Output In-Amp 1
Positive Supply
Rev. A | Page 7 of 24
05947-002
–IN1 1
RG1 2
15 OUT1
14 OUT2
13 –VS
16 +VS
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
AD8222
TYPICAL PERFORMANCE CHARACTERISTICS
N = 1713
500
800
NUMBER OF UNITS
300
200
600
400
–40
–30
–20
–10
0
10
20
30
40
50
CMRR (µV/V)
0
–2.0
05947-003
0
–50
INPUT COMMON-MODE RANGE (V)
NUMBER OF UNITS
200
150
100
40
20
0
20
40
60
80
100
VOSI (µV)
0.5
1.0
1.5
2.0
10
VS = ±15V
5
0
VS = ±5V
–5
–10
–15
–15
05947-004
10
60
0
15
250
80
–0.5
Figure 6. Typical Distribution of Input Offset Current
N = 1713
0
–100
–1.0
IOFFSET (nA)
Figure 3. Typical Distribution for CMRR (G = 1)
300
–1.5
05947-006
200
100
–10
–5
0
5
10
15
OUTPUT VOLTAGE (V)
05947-007
NUMBER OF UNITS
400
Figure 7. Input Common-Mode Range vs. Output Voltage, G = 1
Figure 4. Typical Distribution of Input Offset Voltage
15
N = 1713
500
400
300
200
100
0
–2.0
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
IBIAS (nA)
2.0
05947-005
NUMBER OF UNITS
600
Figure 5. Typical Distribution of Input Bias Current
10
VS = ±15V
5
0
VS = ±5V
–5
–10
–15
–15
–10
–5
0
5
10
15
OUTPUT VOLTAGE (V)
Figure 8. Input Common-Mode Range vs. Output Voltage, G = 100
Rev. A | Page 8 of 24
05947-008
INPUT COMMON-MODE RANGE (V)
700
AD8222
160
150
VS = ±15V
50
0
VS = ±5V
–50
–100
–150
–10
–5
0
5
10
15
COMMON-MODE VOLTAGE (V)
1.6
1.4
–PSRR (dB)
1.2
1.0
0.8
0.6
0.4
0.2
4
6
GAIN = 10
GAIN = 1
1
10
100
8
10
WARM-UP TIME (Minutes)
160
150
140
130
120
110
100
90
80
70
60
50
40
30
20
1k
10k
100k
1M
GAIN = 1000
GAIN = 100
GAIN = 10
10
0
0.1
05947-010
CHANGE IN INPUT OFFSET VOLTAGE (µV)
1.8
2
GAIN = 100
Figure 12. Positive PSRR vs. Frequency, RTI (G = 1 to 1000)
2.0
0
GAIN = 1000
FREQUENCY (Hz)
Figure 9. IBIAS vs. Common-Mode Voltage
0
BANDWIDTH
LIMITED
10
0
0.1
05947-009
–200
–15
140
130
120
110
100
90
80
70
60
50
40
30
20
GAIN = 1
1
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
05947-013
100
+PSRR (dB)
INPUT BIAS CURRENT (pA)
150
05947-012
200
Figure 13. Negative PSRR vs. Frequency, RTI (G = 1 to 1000)
Figure 10. Change in Input Offset Voltage vs. Warm-Up Time
1000
10k
NEGATIVE
600
400
200
POSITIVE
0
OFFSET CURRENT
–200
–400
–600
1k
GAIN = 1
100
GAIN = 10
10
GAIN = 100
GAIN = 1000
–35
–15
5
25
45
65
85
105
125
TEMPERATURE (°C)
Figure 11. Input Bias Current and Offset Current vs. Temperature
1
1
10
100
1k
10k
100k
SOURCE RESISTANCE (Ω)
Figure 14. Total Drift vs. Source Resistance
Rev. A | Page 9 of 24
1M
10M
05947-014
–800
–1000
–55
05947-011
INPUT BIAS CURRENT (pA)
TOTAL DRIFT: 25°C TO 85°C RTI (µV)
800
AD8222
70
60
20
GAIN = 1000
15
50
40
GAIN = 100
10
20
GAIN = 10
10
0
5
ΔCMR (µV/V)
GAIN (dB)
30
GAIN = 1
EXAMPLE PART 1
0
–5
–10
EXAMPLE PART 2
–10
–20
1k
10k
100k
1M
10M
FREQUENCY (Hz)
–20
–40
05947-015
–40
100
INPUT VOLTAGE LIMIT (V)
REFERRED TO SUPPLY VOLTAGES
BANDWIDTH
LIMITED
GAIN = 1
80
70
60
100
1k
10k
100k
1M
–2.0
+2.0
FROM –VS
+1.6
+1.2
+0.8
2
6
10
14
18
Figure 19. Input Voltage Limit vs. Supply Voltage, G = 1
+VS–0
GAIN = 1000
OUTPUT VOLTAGE SWING (V)
REFERRED TO SUPPLY VOLTAGES
–0.4
140
GAIN = 100
120
GAIN = 10
100
BANDWIDTH
LIMITED
90
80
70
GAIN = 1
60
RL = 10kΩ
–0.8
–1.2
RL = 2kΩ
–1.6
+1.6
RL = 2kΩ
+1.2
+0.8
RL = 10kΩ
+0.4
50
1
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
05947-017
CMRR (dB)
–1.6
SUPPLY VOLTAGE (V)
160
40
0.1
–1.2
05947-019
10
Figure 16. CMRR vs. Frequency, RTI
110
120
FROM +VS
–0.8
–VS+0
05947-016
1
FREQUENCY (Hz)
130
100
+0.4
50
150
80
Figure 17. CMRR vs. Frequency, RTI, 1 kΩ Source Imbalance
–VS+0
2
6
10
14
SUPPLY VOLTAGE (V)
Figure 20. Output Voltage Swing vs. Supply Voltage, G = 1
Rev. A | Page 10 of 24
18
05947-020
CMRR (dB)
GAIN = 10
90
40
0.1
60
–0.4
GAIN = 100
110
100
40
+VS–0
GAIN = 1000
130
120
20
Figure 18. ΔCMR vs. Temperature, G = 1
150
140
0
TEMPERATURE (°C)
Figure 15. Gain vs. Frequency
160
–20
05947-018
–15
–30
AD8222
30
40
NONLINEARITY (10ppm/DIV)
OUTPUT VOLTAGE SWING (V p-p)
30
20
10
20
2kΩ LOAD
10
0
600Ω LOAD
–10
10kΩ LOAD
–20
10
100
1k
10k
LOAD RESISTANCE (Ω)
–40
–10
–8
VOLTAGE NOISE SPECTRAL DENSITY (nV/ Hz)
–2
–3
+3
+2
SINKING
+1
1
2
3
4
5
6
7
8
9
10
11
12
OUTPUT CURRENT (mA)
05947-022
OUTPUT VOLTAGE SWING (V)
REFERRED TO SUPPLY VOLTAGES
SOURCING
0
–2
0
2
4
6
8
10
Figure 24. Gain Nonlinearity, G = 100
+VS–0
–VS+0
–4
VOUT (V)
Figure 21. Output Voltage Swing vs. Load Resistance
–1
–6
1k
GAIN = 1
100
GAIN = 10
GAIN = 100
10
GAIN = 1000
1
GAIN = 1000
BW LIMIT
1
10
100
1k
10k
100k
FREQUENCY (Hz)
Figure 25. Voltage Noise Spectral Density vs. Frequency (G = 1 to 1000)
Figure 22. Output Voltage Swing vs. Output Current, G = 1
4
2
10kΩ LOAD
0
2kΩ LOAD
–1
600Ω LOAD
–2
–4
–10
05947-027
–3
–8
–6
–4
–2
0
2
4
VOUT (V)
6
8
10
05947-023
NONLINEARITY (1ppm/DIV)
3
1
05947-026
1
05947-021
0
05947-024
–30
Figure 23. Gain Nonlinearity, G = 1
2µV/DIV
1s/DIV
Figure 26. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1)
Rev. A | Page 11 of 24
AD8222
30
0.1µV/DIV
25
20
15
10
5
0
1k
1s/DIV
GAIN = 1
10k
100k
1M
FREQUENCY (Hz)
Figure 27. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1000)
Figure 30. Large Signal Frequency Response
5V/DIV
100
7.4µs TO 0.01%
8.3µs TO 0.001%
1
10
100
1k
10k
100k
FREQUENCY (Hz)
05947-029
20µs/DIV
10
05947-032
0.002%/DIV
Figure 31. Large Signal Pulse Response and Settling Time (G = 1)
Figure 28. Current Noise Spectral Density vs. Frequency
5V/DIV
4.8µs TO 0.01%
6.6µs TO 0.001%
5pA/DIV
20µs/DIV
1s/DIV
Figure 32. Large Signal Pulse Response and Settling (G = 10)
Figure 29. 0.1 Hz to 10 Hz Current Noise
Rev. A | Page 12 of 24
05947-033
0.002%/DIV
05947-030
CURRENT NOISE SPECTRAL DENSITY (fA/ Hz)
1k
05947-031
05947-028
MAX OUTPUT VOLTAGE (V p-p)
GAIN = 10, 100, 1000
AD8222
5V/DIV
9.2µs TO 0.01%
16.2µs TO 0.001%
20mV/DIV
4µs/DIV
05947-037
20µs/DIV
05947-034
0.002%/DIV
Figure 36. Small Signal Response, G = 10, RL = 2 kΩ, CL = 100 pF
Figure 33. Large Signal Pulse Response and Settling Time (G = 100)
5V/DIV
83µs TO 0.01%
112µs TO 0.001%
20mV/DIV
4µs/DIV
05947-036
Figure 34. Large Signal Pulse Response and Settling Time (G = 1000)
10µs/DIV
05947-038
20mV/DIV
Figure 37. Small Signal Response, G = 100, RL = 2 kΩ, CL = 100 pF
20mV/DIV
100µs/DIV
05947-039
200µs/DIV
05947-035
0.002%/DIV
Figure 38. Small Signal Response, G = 1000, RL = 2 kΩ, CL = 100 pF
Figure 35. Small Signal Response, G = 1, RL = 2 kΩ, CL = 100 pF
Rev. A | Page 13 of 24
AD8222
15
60
GAIN = 1000
GAIN = 100
10
SETTLED TO 0.001%
GAIN (dB)
SETTLING TIME (µs)
40
SETTLED TO 0.01%
5
20
GAIN = 10
0
GAIN = 1
0
5
10
15
20
OUTPUT VOLTAGE STEP SIZE (V)
–40
100
05947-040
0
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 39. Settling Time vs. Step Size (G = 1)
05947-043
–20
Figure 42. Differential Output Configuration: Gain vs. Frequency
100
1k
OUTPUT BALANCE = 20 log
90
VDIFF_OUT
VCM_OUT
OUTPUT BALANCE (dB)
SETTLING TIME (µs)
80
100
SETTLED TO 0.001%
10
70
LIMITED BY
MEASUREMENT
SYSTEM
60
50
40
30
20
SETTLED TO 0.01%
10
1k
100
GAIN
Figure 40. Settling Time vs. Gain for a 10 V Step
200
SOURCE
VOUT = 20V p-p
CHANNEL SEPARATION (dB)
180
GAIN = 1000
SOURCE VOUT
SMALLER TO
AVOID SLEW
RATE LIMIT
THERMAL CROSSTALK
VARIES WITH LOAD
120
GAIN = 1
100
1
10
100
1k
10k
FREQUENCY (Hz)
100k
1M
05947-042
80
60
1
10
100
1k
10k
100k
FREQUENCY (Hz)
Figure 43. Differential Output Configuration:
Output Balance vs. Frequency
160
140
0
Figure 41. Channel Separation vs. Frequency, RL = 2 kΩ, Source Channel at G = 1
Rev. A | Page 14 of 24
1M
05947-056
1
05947-041
10
1
AD8222
THEORY OF OPERATION
VB
I
A1
IB COMPENSATION
I
A2
IB COMPENSATION
10kΩ
C1
C2
+VS
10kΩ
OUTPUT
10kΩ
+VS
400Ω
–IN
Q1
R2
+VS
R1 24.7kΩ
+VS
A3
+VS
24.7kΩ
+VS
400Ω
Q2
+IN
–VS
REF
10kΩ
RG
–VS
–VS
05947-045
–VS
–VS
–VS
Figure 44. Simplified Schematic
AMPLIFIER ARCHITECTURE
GAIN SELECTION
The two instrumentation amplifiers of the AD8222 are based
on the classic 3-op-amp topology. Figure 44 shows a simplified
schematic of one of the amplifiers. The input transistors, Q1
and Q2, are biased at a fixed current. Any differential input
signal forces the output voltages of A1 and A2 to change so that
the differential voltage also appears across RG. The current that
flows through RG must also flow through R1 and R2, resulting
in a precisely amplified version of the differential input signal
between the outputs of A1 and A2. Topologically, Q1 + A1 + R1
and Q2 + A2 + R2 can be viewed as precision current feedback
amplifiers. The common-mode signal and the amplified differential signal are applied to a difference amplifier that rejects the
common-mode voltage. The difference amplifier employs innovations that result in low output offset voltage as well as low output
offset voltage drift.
Placing a resistor across the RG terminals sets the gain of the
AD8222, which can be calculated by referring to Table 8 or by
using the following gain equation:
Because the input amplifiers employ a current feedback architecture, the gain-bandwidth product of the AD8222 increases
with gain, resulting in a system that does not suffer from the
expected bandwidth loss of voltage feedback architectures at
higher gains.
The transfer function of the AD8222 is
VOUT = G(V+IN − V−IN) + VREF
RG 
G 1
Table 8. Gains Achieved Using 1% Resistors
1% Standard Table Value of RG (Ω)
49.9 k
12.4 k
5.49 k
2.61 k
1.00 k
499
249
100
49.9
Calculated Gain
1.990
4.984
9.998
19.93
50.40
100.0
199.4
495.0
991.0
The AD8222 defaults to G = 1 when no gain resistor is used.
The tolerance and gain drift of the RG resistor should be added
to the AD8222’s specifications to determine the total gain
accuracy of the system. When the gain resistor is not used,
gain error and gain drift are kept to a minimum.
where:
G 1
49.4 kΩ
49.4 kΩ
RG
Rev. A | Page 15 of 24
AD8222
REFERENCE TERMINAL
The output voltage of an AD8222 channel is developed with
respect to the potential on the corresponding reference terminal.
Typically the reference terminal is connected to ground, but it
can also be driven with a voltage to offset the output signal. For
example, connect a voltage to the reference terminal to levelshift the output so that the AD8222 can drive a single-supply
ADC. Both REF1 and REF2 are protected with ESD diodes and
should not exceed either +VS or −VS by more than 0.3 V.
For best performance, source impedance to a reference terminal
should be kept below 1 Ω. As shown in Figure 44, the reference
terminal is at one end of a 10 kΩ resistor. Additional impedance
at the reference terminal adds to this 10 kΩ resistor and results
in amplification of the signal connected to the positive input.
The amplification from the additional RREF can be computed by
2 10 kΩ  RREF 
20 kΩ  RREF
Only the positive signal path is amplified; the negative path is
unaffected. This uneven amplification degrades the amplifier’s
CMRR.
INCORRECT
CORRECT
AD8222
REF
REF
V
This package is included primarily for legacy reasons. Because
the AD8222 dissipates so little power, there is little need for the
thermal pad.
The thermal pad is connected internally to −VS. The pad can
either be left unsoldered, soldered to an otherwise unconnected
PCB landing, or soldered to a landing connected to the negative
supply rail (−VS). If pin compatibility with the AD8224 is
desired, the pad should not be electrically connected to any net,
including −VS.
The solder process can leave flux and other contaminants on
the board. When these contaminants are between the AD8222
leads and thermal pad, they can create leakage paths that are
larger than the AD8222’s bias currents. A thorough washing
process removes these contaminants and restores the AD8222’s
excellent bias current performance.
The AD8222 is a high precision device. To ensure optimum
performance at the PC board level, care must be taken in the
design of the board layout. The AD8222 pinout is arranged in a
logical manner to aid in this task.
AD8222
REF
V
Package with Thermal Pad
LAYOUT
CORRECT
AD8222
Outline Dimensions section. This metal is connected to −VS
through the part. Because of a possibility of a short, vias should
not be placed underneath this exposed metal.
Common-Mode Rejection Over Frequency
+
+
OP2177
AD8222
–
–
05947-054
V
Figure 45. Driving the Reference Pin
PACKAGE CONSIDERATIONS
The AD8222 comes in a 4 mm × 4 mm LFCSP. Beware of
blindly copying the footprint from another 4 mm × 4 mm
LFCSP part; the landing pattern may be different. Refer to
the Outline Dimensions section to verify that the PCB symbol
has the correct dimensions.
The AD8222 has a higher CMRR over frequency than typical
in-amps, which gives it greater immunity to disturbances, such
as line noise and its associated harmonics. A well-implemented
layout is required to maintain this high performance. Input
source impedances should be matched closely. Source resistance
should be placed close to the inputs so that it interacts with as
little parasitic capacitance as possible.
Parasitics at the RGx pins can also affect CMRR over frequency.
The PCB should be laid out so that the parasitic capacitances at
each pin match. Traces from the gain setting resistor to the RGx
pins should be kept short to minimize parasitic inductance.
Reference
The AD8222 comes in two package varieties, both with and
without a thermal pad.
Errors introduced at the reference terminal feed directly to the
output. Care should be taken to tie REF to the appropriate local
ground.
Package Without Thermal Pad
The AD8222 ships with a package that does not include a thermal
pad; it is the preferred package for the AD8222. Unlike chip
scale packages where the pad limits routing capability, the AD8222
package allows routes and vias directly underneath the chip, so
that the full space savings of the small LFCSP can be realized.
Although the package has no metal in the center of the part, the
manufacturing process does leave a very small section of exposed
metal at each of the package corners, shown in Figure 55 in the
Power Supplies
A stable dc voltage should be used to power the instrumentation
amplifier. Noise on the supply pins can adversely affect
performance.
The AD8222 has two positive supply pins (Pin 5 and Pin 16)
and two negative supply pins (Pin 8 and Pin 13). Although the
part functions with only one pin from each supply pair connected,
Rev. A | Page 16 of 24
AD8222
both pins should be connected for specified performance and
optimum reliability.
The AD8222 should be decoupled with 0.1 μF bypass capacitors,
one for each supply. The positive supply decoupling capacitor
should be placed near Pin 16, and the negative supply decoupling capacitor should be placed near Pin 8. Each supply should
also be decoupled with a 10 μF tantalum capacitor. The tantalum
capacitor can be placed further away from the AD8222 and can
generally be shared by other precision integrated circuits. Figure
46 shows an example layout.
INPUT BIAS CURRENT RETURN PATH
The input bias current of the AD8222 must have a return path
to common. When the source, such as a thermocouple, cannot
provide a return current path, one should be created, as shown
in Figure 47.
INCORRECT
CORRECT
+VS
+VS
AD8222
AD8222
REF
REF
–VS
0.1µF
–VS
TRANSFORMER
TRANSFORMER
+VS
16
15
14
+VS
13
AD8222
AD8222
12
1
AD8222
REF
REF
11
2
RG2
RG1
3
10
4
9
5
6
7
10MΩ
–VS
–VS
THERMOCOUPLE
THERMOCOUPLE
+VS
8
+VS
C
C
0.1µF
R
1
fHIGH-PASS = 2πRC
AD8222
C
REF
AD8222
C
REF
–VS
–VS
CAPACITIVELY COUPLED
Figure 46. Example Layout
CAPACITIVELY COUPLED
Figure 47. Creating an IBIAS Path
Rev. A | Page 17 of 24
05947-047
05947-046
R
AD8222
+15V
INPUT PROTECTION
All terminals of the AD8222 are protected against ESD (1 kV,
human body model). In addition, the input structure allows for
dc overload conditions of about 2.5 V beyond the supplies.
0.1µF
R
Input Voltages Beyond the Rails
+IN
4.02kΩ
CD
R1
10nF 499Ω
For larger input voltages, an external resistor should be used in
series with each input to limit current during overload conditions.
The AD8222 can safely handle a continuous 6 mA current. The
limiting resistor can be computed from
VOUT
AD8222
R
REF
–IN
4.02kΩ
CC
1nF
0.1µF
V  VSUPPLY
 IN
 400 Ω
6 mA
10µF
–15V
05947-048
RLIMIT
10µF
CC
1nF
Figure 48. RFI Suppression
For applications in which the AD8222 encounters extreme overload voltages, such as cardiac defibrillators, external series
resistors and low leakage diode clamps, such as the BAV199L,
the FJH1100, or the SP720, should be used.
Differential Input Voltages at High Gains
When operating at high gain, large differential input voltages
can cause more than 6 mA of current to flow into the inputs.
This condition occurs when the differential voltage exceeds
the following critical voltage:
Figure 48 shows an example where the differential filter frequency is approximately 2 kHz, and the common-mode filter
frequency is approximately 40 kHz.
Values of R and CC should be chosen to minimize RFI. Mismatch
between the R × CC at the positive input and the R × CC at
negative input degrades the CMRR of the AD8222. By using a
value of CD 10× larger than the value of CC, the effect of the
mismatch is reduced and performance is improved.
COMMON-MODE INPUT VOLTAGE RANGE
VCRITICAL = (400 + RG) × (6 mA)
This is true for differential voltages of either polarity.
The maximum allowed differential voltage can be increased by
adding an input protection resistor in series with each input.
The value of each protection resistor should be
RPROTECT = (VDIFF_MAX − VCRITICAL)/6 mA
RF INTERFERENCE
The 3-op-amp architecture of the AD8222 applies gain and then
removes the common-mode voltage. Therefore, internal nodes
in the AD8222 experience a combination of both the gained
signal and the common-mode signal. This combined signal can
be limited by the voltage supplies even when the individual
input and output signals are not. Figure 7 and Figure 8 show the
allowable common-mode input voltage ranges for various
output voltages, supply voltages, and gains.
RF rectification is often a problem when amplifiers are used in
applications where there are strong RF signals. The disturbance
can appear as a small dc offset voltage. High frequency signals
can be filtered with a low-pass, RC network placed at the input
of the instrumentation amplifier, as shown in Figure 48. The
filter limits the input signal bandwidth according to the
following relationship:
FilterFreqDiff 
1
2 R(2CD  CC )
FilterFreqCM 
1
2 R  C C
where CD ≥ 10CC.
Rev. A | Page 18 of 24
AD8222
APPLICATIONS INFORMATION
DIFFERENTIAL OUTPUT
Setting the Common-Mode Voltage
The differential configuration of the AD8222 has the same
excellent dc precision specifications as the single-ended output
configuration and is recommended for applications in the
frequency range of dc to 100 kHz.
The output common-mode voltage is set by the average of +IN2
and REF2. The transfer function is
The circuit configuration is shown in Figure 49. The differential
output specifications in Table 2 and Table 4 refer to this configuration only. The circuit includes an RC filter that maintains the
stability of the loop.
The transfer function for the differential output is:
2-Channel Differential Output Using a Dual Op Amp
+
Another differential output topology is shown in Figure 50.
Instead of a second in-amp, ½ of a dual OP2177 op amp creates
the inverted output. Because the OP2177 is packaged in an
MSOP, this configuration allows the creation of a dual channel,
precision differential output in-amp with little board area.
+OUT
10kΩ
–
AD8222
100pF
+IN2
REF2
–OUT
Figure 49. Differential Circuit Schematic
Errors from the op amp are common to both outputs and are
thus common mode. Errors from mismatched resistors also
create a common-mode dc offset. Because these errors are
common mode, they will likely be rejected by the next device
in the signal chain.
+IN
AD8222
+OUT
–IN
REF
4.99kΩ
4.99kΩ
VREF
+
–
OP2177
–OUT
Figure 50. Differential Output Using Op Amp
Rev. A | Page 19 of 24
05947-053
AD8222
05947-049
–IN
RG
+
RG
49.4 kΩ
–
+IN
+IN2 and REF2 have different properties that allow the
reference voltage to be easily set for a wide variety of applications.
+IN2 has high impedance but cannot swing to the supply rails
of the part. REF2 must be driven with a low impedance but can
go 300 mV beyond the supply rails.
A common application sets the common-mode output voltage
to the midscale of a differential ADC. In this case, the ADC
reference voltage is sent to the +IN2 terminal, and ground is
connected to the REF2 terminal. This produces a common-mode
output voltage of half the ADC reference voltage.
VDIFF_OUT = V+OUT − V−OUT = (V+IN − V−IN) × G
where G  1 
VCM_OUT = (V+OUT + V−OUT)/2 = (V+IN2 + VREF2)/2
AD8222
+12V
10µF
+
0.1µF
+5V
1kΩ
+IN
100pF
NPO
5%
0.1µF
+OUT
1000pF
AD8222
–IN
+IN2
100pF
NPO
5%
–OUT
REF2
IN–
2200pF
2200pF
+
AD7688
GND
REF
10µF
X5R
+12V
+5V REF
10µF
VDD
IN+
1kΩ
(DIFF OUT)
1kΩ
1kΩ
0.1µF
0.1µF
VIN
–12V
+5V REF
VOUT
ADR435
0.1µF
05947-051
GND
Figure 51. Driving a Differential ADC
The AD8222 can be configured in differential output mode
to drive a differential analog-to-digital converter. Figure 51
illustrates several of the concepts.
RFI and Antialiasing Filter
The 1 kΩ resistors, 1000 pF capacitor, and 100 pF capacitors in
front of the in-amp form filter circuitry that performs many
functions. The 1 kΩ and 100 pF capacitors form common-mode
filters that protect the amplifier from incoming radio frequency
signals. Without the filtering, these RFI signals can be rectified
in the in-amp. The 1 kΩ resistors provide some overvoltage
protection. The 1 kΩ resistors and 1000 pF capacitor form a
76 kHz antialiasing filter for the ADC.
Note that the 100 pF capacitors are 5% COG/NPO types. These
capacitors match well over time and temperature, which keeps
the system CMRR high over frequency.
Second Antialiasing Filter
A 1 kΩ resistor and 2200 pF capacitor are placed between each
AD8222 output and ADC input. They create a 72 kHz low-pass
filter for another stage of antialiasing protection.
The 1 kΩ resistors can also protect an ADC from overvoltages.
Because the AD8222 runs on wider supply voltages than a
typical ADC, there is a possibility of overdriving the ADC. This
is not an issue with a PulSAR® converter, such as the AD7688.
Its input can handle a 130 mA overdrive, which is much higher
than the short-circuit limit of the AD8222. However, other converters have less robust inputs and may need the added protection.
Reference
The ADR435 supplies a reference voltage to both the ADC and
the AD8222. Because REF2 on the AD8222 is grounded, the
common-mode output voltage is precisely half the reference
voltage, exactly where it needs to be for the ADC.
PRECISION STRAIN GAGE
The low offset and high CMRR over frequency of the AD8222
make it an excellent candidate for both ac and dc bridge measurements. As shown in Figure 52, the bridge can be connected to
the inputs of the amplifier directly.
5V
10µF
350Ω
0.1µF
350Ω
+IN
These four elements also improve distortion performance. The
2200 pF capacitor provides charge to the switched capacitor
front end of the ADC, and the 1 kΩ resistor shields the AD8222
from driving any sharp current changes. If the application
requires a lower frequency antialiasing filter and is distortion
sensitive, increase the value of the capacitor rather than the
resistor.
Rev. A | Page 20 of 24
350Ω
350Ω
+
AD8222
RG
–IN
–
Figure 52. Precision Strain Gauge
2.5V
05947-050
DRIVING A DIFFERENTIAL INPUT ADC
AD8222
DRIVING CABLING
All cables have a certain capacitance per unit length, which
varies widely with cable type. The capacitive load from the cable
may cause peaking in the AD8222’s output response. To reduce
the peaking, use a resistor between the AD8222 and the cable.
Because cable capacitance and desired output response vary
widely, this resistor is best determined empirically. A good
starting point is 50 Ω.
(DIFF OUT)
AD8222
(SINGLE OUT)
05947-052
The AD8222 operates at a low enough frequency that
transmission line effects are rarely an issue; therefore, the
resistor need not match the characteristic impedance of
the cable.
AD8222
Figure 53. Driving a Cable
Rev. A | Page 21 of 24
AD8222
OUTLINE DIMENSIONS
4.00
BSC SQ
0.50
0.40
0.30
0.60 MAX
12 13
PIN 1
INDICATOR
3.75
BSC SQ
1
16
EXPOSED
PAD
0.65
BSC
TOP VIEW
4
2.65
2.50 SQ
2.35
5
8
9
PIN 1
INDICATOR
0.25 MIN
1.95 BCS
0.80 MAX
0.65 TYP
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
0.05 MAX
0.02 NOM
COPLANARITY
0.20 REF
0.08
031006-A
12° MAX
1.00
0.85
0.80
SEATING
0.30
PLANE
0.23
0.18
COMPLIANT TO JEDEC STANDARDS MO-220-VGGC.
Figure 54. 16-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 4 mm Body, Very Thin Quad
(CP-16-13)
Dimensions are shown in millimeters
0.60 MAX
4.00
BSC SQ
0.60 MAX
PIN 1
INDICATOR
3.75
BCS SQ
0.65
BSC
13
12
TOP VIEW
SEATING
PLANE
12° MAX
8
5
4
BOTTOM VIEW
0.80 MAX
0.65 TYP
0.35
0.30
0.25
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-263-VBBC
Figure 55. 16-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 4 mm Body, Very Thin Quad, with Hidden Paddle
CP-16-19
Dimensions shown in millimeters
Rev. A | Page 22 of 24
062309-B
1.00
0.85
0.80
1
1.95 REF
SQ
9
0.75
0.60
0.50
16
AD8222
ORDERING GUIDE
Model1
AD8222ACPZ-R7
Temperature
Range
−40°C to +85°C
Product Description
Standard Grade with Thermal Pad
AD8222ACPZ-RL
−40°C to +85°C
Standard Grade with Thermal Pad
AD8222ACPZ-WP
−40°C to +85°C
Standard Grade with Thermal Pad
AD8222BCPZ-R7
−40°C to +85°C
High Performance Grade with Thermal Pad
AD8222BCPZ-RL
−40°C to +85°C
High Performance Grade with Thermal Pad
AD8222BCPZ-WP
−40°C to +85°C
High Performance Grade with Thermal Pad
AD8222HACPZ-R7
−40°C to +85°C
Standard Grade Without Thermal Pad
AD8222HACPZ-RL
−40°C to +85°C
Standard Grade Without Thermal Pad
AD8222HACPZ-WP
−40°C to +85°C
Standard Grade Without Thermal Pad
AD8222HBCPZ-R7
−40°C to +85°C
High Performance Grade Without Thermal Pad
AD8222HBCPZ-RL
−40°C to +85°C
High Performance Grade Without Thermal Pad
AD8222HBCPZ-WP
−40°C to +85°C
High Performance Grade Without Thermal Pad
AD8222-EVALZ
1
Z = RoHS Compliant Part.
Rev. A | Page 23 of 24
Package Description
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], 7“ Tape and Reel
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], 13“Tape and Reel
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], Waffle Pack
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], 7“ Tape and Reel
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], 13” Tape and Reel
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], Waffle Pack
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], 7” Tape and Reel
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], 13” Tape and Reel
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], Waffle Pack
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], 7” Tape and Reel
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], 13” Tape and Reel
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ], Waffle Pack
Evaluation Board
Package
Option
CP-16-13
CP-16-13
CP-16-13
CP-16-13
CP-16-13
CP-16-13
CP-16-19
CP-16-19
CP-16-19
CP-16-19
CP-16-19
CP-16-19
AD8222
NOTES
©2006–2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05947-0-2/10(A)
Rev. A | Page 24 of 24