DTDG14GP Transistors 1A / 60V Digital Transistor (with built-in resistor and zener diode) DTDG14GP zExternal dimensions (Unit : mm) zApplications Driver 1.5 2.5 4.0 zFeatures 1) High hFE. 300 (Min.) (VCE / IC=2V / 0.5A) 2) Low saturation voltage, (VCE(sat)=0.4V at IC / IB=500mA / 5mA) 3) Built-in zener diode gives strong protection against reverse surge by L- load (an inductive load). 0.5 4.5 1.6 (2) (3) 1.0 (1) 0.5 0.4 1.5 1.5 3.0 ROHM : MPT3 EIAJ : SC-62 zStructure NPN epitaxial planar silicon transistor (with built-in resistor and zener diode) 0.4 0.4 Abbreviated symbol : E01 (1) Base (2) Collector (3) Emitter zEquivalent circuit (2) zPackaging specifications (1) Part No. Package MPT3 Packaging type Taping Code T100 Basic ordering unit (pieces) 1000 R (3) (1) : Base (2) : Collector (3) : Emitter R=10kΩ DTDG14GP zAbsolute maximum ratings (Ta = 25°C) Parameter Symbol Limits Unit Collector-base voltage VCBO 60±10 V Collector-emitter voltage VCEO 60±10 V Emitter-base voltage VEBO 5 V IC 1 A Collector current ICP 2 ∗1 0.5 A W Collector power dissipation PC Junction temperature Tj 150 °C Storage temperature Tstg −55 to +150 °C 2 ∗2 ∗1 Pw≤10ms, Duty cycle≤1/2 ∗2 When mounted on a 40×40×0.7 mm ceramic board. Rev.A 1/2 DTDG14GP Transistors zElectrical characteristics (Ta = 25°C) Symbol Min. Typ. Max. Unit Collector-base breakdown voltage BVCBO 50 − 70 V IC=50µA Collector-emitter breakdown voltage BVCEO 50 − 70 V IC=1mA Emitter-base breakdown voltage BVEBO 5 − − V IE=720µA ICBO − − 0.5 µA VCB=40V Parameter Collector cutoff current Conditions IEBO 300 − 580 µA VEB=4V VCE(sat) − − 0.4 V IC/IB=500mA/5mA DC current transfer ratio hFE 300 − − − VCE=2V, IC=500mA Emitter-base resistance R 7 10 13 kΩ Transition frequency fT ∗ − 80 − MHz Emitter cutoff current Collector-emitter saturation voltage − VCE=5V, IE=−0.1A, f=30MHz ∗ Characteristics of built-in transistor 10 10k ICP 2 PW 1 PW 500m =1 0m =1 s∗ 00 200m m DC 100m s∗ 50m 20m 10m 5m 14W×18l×0.8t(Unit : mm) When mounted on glass epoxy 2m ∗Single pulse 1m 100m 200m 500m 1 2 5 10 2k 1k 500 200 100 VCE=5V 2V 1V 50 100 Safe operating area 10 10m 20m 50m 100m200m500m 1 2 1 100m 2 5 10 COLLECTOR CURRENT : IC (A) Fig.2 Ta=25°C 5 200m 20 20 10 500m 50 COLLECTOR TO EMITTER VOLTAGE : VCE (V) Fig.1 Ta=25°C 5k DC CURRENT GAIN : hFE COLLECTOR CURRENT : IC (A) 5 COLLECTOR SATURATION VOLTAGE : VCE(sat) (V) zElectrical characteristic curves DC current gain vs. collector current IC/IB=200 100 50 50m 20m 10m 10m 20m 50m 100m 200m 500m 1 2 5 10 COLLECTOR CURRENT : IC (A) Fig.3 Collector-emitter saturation voltage vs. collector current Rev.A 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1