ROHM 2SB1427_1

2SB1427
Transistors
Power transistor (−20V, −2A)
2SB1427
zExternal dimensions (Unit : mm)
zFeatures
1) Low saturation voltage,
VCE : Max . −0.5V at IC/IB = −1A / −50mA.
2) Excellent DC current gain characteristics.
4.0
1.5
0.4
1.0
2.5
1.6
0.5
4.5
(1)
(2)
3.0
0.5
0.4
ROHM : MPT3
EIAJ : SC-62
(1) Base
(2) Collector
(3) Emitter
1.5
1.5
0.4
(3)
zAbsolute maximum ratings (Ta=25°C)
Symbol
Limits
Unit
Collector-base voltage
Collector-emitter voltage
Parameter
VCBO
VCEO
−20
−20
V
V
Emitter-base voltage
VEBO
−6
−2
V
A(DC)
−3
0.5
A(Pulse)
∗1
W
∗2
Collector current
IC
Collector power dissipation
PC
2
150
−55 ~ +150
Tj
Junction temperature
Storage temperature
Tstg
°C
°C
∗1 Single pulse, Pw=10ms
∗2 When mounted on a 40×40×0.7mm ceramic board.
zPackaging specifications and hFE
Type
2SB1427
Package
hFE
Marking
MPT3
E
Code
Basic ordering unit (pieces)
T100
1000
∗
BJ
∗ Denotes hFE
zElectrical characteristics (Ta=25°C)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Collector-base breakdown voltage
Collector-emitter breakdown voltage
BVCBO
BVCEO
−20
−20
−
−
−
−
V
V
IC = −50µA
IC = −1mA
Emitter-base breakdown voltage
BVEBO
−
hFE
390
−
−
−0.5
−0.5
−0.5
820
V
µA
µA
V
−
IE = −50µA
VCB = −16V
IEBO
VCE(sat)
−6
−
−
−
Transition frequency
fT
−
90
−
MHz
Output capacitance
Cob
−
30
−
pF
Collector cutoff current
Emitter cutoff current
Collector-emitter saturation voltage
DC current transfer ratio
ICBO
−
−
−
Conditions
VEB = −5V
IC/IB = −1A/−50mA
∗
VCE/IC = −6V/−0.5A
VCE = −10V , IE = 10mA , f= 100MHz
VCB = −10V , IE = 0A , f = 1MHz
∗ Measured using pulse current.
Rev.A
1/2
2SB1427
zElectrical characteristics curves
5k
DC CURRENT GAIN : hFE
COLLECTOR CURRENT : IC(mA)
−2A
−1A
−500
−200
−100
−50
−20
−10
−5
−2
−1
−0
−0.5
−1.0
−1.5
BASE TO EMITTER VOLTAGE : VBE (V)
Fig.1 Grounded emitter propagation
characteristics
10
5
COLLECTOR CURRENT : IC (A)
VCE= −6V
Ta=25°C
VCE= −2V
−5A
2k
1k
Ta=100°C
25°C
500
−50°C
200
100
50
20
−1m
−10m
−100m
−1
−10
COLLECTOR CURRENT : IC (A)
Fig.2 DC current gain vs. collector current
COLLECTOR SATURATION VOLTAGE : VCE(sat) (V)
Transistors
−1
Ta=25°C
IC/IB=20
−500m
−200m
−100m
−50m
−20m
−10m
−5m
−2m
−1m
−1m
−10m
−100m
−1
−10
COLLECTOR CURRENT : IC (A)
Fig.3 Collector-emitter saturation
voltage vs. collector current
Ic Max. (Pulse∗)
Pw=10ms∗
2
1
500m
Pw=100ms∗
DC
200m
100m
50m
20m
10m
5m Ta=25°C
∗ Single
2m
NONREPETITIVE
PULS
1m
0.1 0.2
0.5 1
2
5 10
20 50 100 200 500 1000
COLLECTOR TO EMITTER VOLTAGE : VCE (V)
Fig.4 Safe Operating area
Rev.A
2/2
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1