LTC3265 - Low Noise Dual Supply with Boost and Inverting Charge Pumps

LTC3265
Low Noise Dual Supply
with Boost and Inverting
Charge Pumps
DESCRIPTION
FEATURES
Boost Charge Pump Generates 2 • VIN_P
(VIN_P Range: 4.5V to 16V)
nn Inverting Charge Pump Generates –V
IN_N
(VIN_N Range: 4.5V to 32V)
nn Low Noise Positive LDO Post Regulator Up to 50mA
nn Low Noise Negative LDO Post Regulator Up to 50mA
nn 135µA Quiescent Current in Burst Mode® Operation
with Both LDO Regulators On
nn 50kHz to 500kHz Programmable Oscillator Frequency
nn Stable with Ceramic Capacitors
nn Short-Circuit/Thermal Protection
nn Low Profile 3mm × 5mm 18-Lead DFN and Thermally
Enhanced 20-Lead TSSOP Packages
nn
APPLICATIONS
nn
nn
Low Noise Bipolar/Inverting Supplies
Industrial/Instrumentation Low Noise Bias Generators
L, LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks
and ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the
property of their respective owners.
The LTC®3265 is a low noise dual polarity output power
supply including a boost charge pump, an inverting charge
pump and two low noise positive and negative LDO post
regulators. The boost charge pump powers the positive
LDO post regulator while the inverting charge pump powers the negative LDO regulator. Each LDO can provide up
to 50mA of output current. The LDO output voltages can
be adjusted using external resistor dividers.
The charge pumps employ low quiescent current
Burst Mode operation or low noise constant frequency
mode. During Burst Mode operation, the boost charge
pump regulates its output (VOUT+) to 0.94 • 2 • VIN_P while
the inverting charge pump regulates its output (VOUT–)
to –0.94 • VIN_N. In Burst Mode operation the LTC3265
draws only 135µA of quiescent current with both LDOs
on. In constant frequency mode, the boost and inverting
charge pumps produce outputs equal to 2 • VIN_P and
–VIN_N respectively and operate at a fixed 500kHz or to
a programmed value between 50kHz to 500kHz using an
external resistor. The LTC3265 is available in low profile
3mm × 5mm × 0.75mm 18-lead DFN and thermally
enhanced 20-lead TSSOP packages.
TYPICAL APPLICATION
LDO Rejection of VOUT ± Ripple
Low Noise ±15V Outputs from a Single 12V Input
1µF
CBST+ CBST –
VOUT+
VIN_N
12V
+15V
10µF
LTC3265
1µF
10µF
LDO+
VIN_P
10µF
VOUT+
10mV/DIV
AC-COUPLED
EN+
EN–
ADJ+
BYP+
MODE
GND
CINV+
BYP–
CINV –
ADJ–
VOUT–
LDO–
100nF
604K
VLDO+
10mV/DIV
AC-COUPLED
VLDO–
10mV/DIV
AC-COUPLED
VOUT–
10mV/DIV
AC-COUPLED
52.3k
1µs/DIV
100nF
52.3k
604K
10µF
RT
3265 TA01b
+
–15V
10µF
VIN_P = 12V, VIN_N = VOUT
VLDO+ = 15V
VLDO– = –15V
fOSC = 500kHz
ILDO+ = 20mA
ILDO– = –20mA
3265 TA01a
3265fa
For more information www.linear.com/LTC3265
1
LTC3265
ABSOLUTE MAXIMUM RATINGS
(Notes 1, 3)
VIN_P, EN+, EN–, MODE............................... –0.3V to 18V
VOUT+, VIN_N ............................................... –0.3V to 36V
LDO+.............................................................–16V to 36V
VOUT–, LDO –............................................... –36V to 0.3V
RT, ADJ+....................................................... –0.3V to 6V
BYP+.......................................................... –0.3V to 2.5V
ADJ –............................................................. –6V to 0.3V
BYP–.......................................................... –2.5V to 0.3V
LDO± Short-Circuit Duration............................. Indefinite
Operating Junction Temperature Range
(Note 2)................................................... –55°C to 150°C
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec)
FE Only.............................................................. 300°C
PIN CONFIGURATION
TOP VIEW
TOP VIEW
CBST –
1
CBST+
2
17 LDO+
VIN_P
3
16 ADJ+
EN –
4
15 BYP+
BYP –
5
ADJ –
6
LDO –
7
12 RT
VOUT –
8
11 VIN_N
10 CINV+
CINV –
18 VOUT+
19
GND
9
NC
1
20 VOUT+
CBST –
2
19 LDO+
CBST+
3
18 ADJ+
VIN_P
4
17 BYP+
EN –
5
BYP –
6
–
ADJ
7
14 RT
LDO –
8
13 VIN_N
VOUT –
9
12 CINV +
14 MODE
13 EN+
21
GND
CINV – 10
DHC PACKAGE
18-LEAD (5mm × 3mm) PLASTIC DFN
TJMAX = 150°C, θJA = 42°C/W
EXPOSED PAD (PIN 19) IS GND, MUST BE SOLDERED TO PCB
16 MODE
15 EN+
11 NC
FE PACKAGE
20-LEAD PLASTIC TSSOP
TJMAX = 150°C, θJA = 38°C/W
EXPOSED PAD (PIN 21) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
(http://www.linear.com/product/LTC3265#orderinfo)
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC3265EDHC#PBF
LTC3265EDHC#TRPBF
3265
18-Lead (5mm × 3mm) Plastic DFN
–40°C to 125°C
LTC3265IDHC#PBF
LTC3265IDHC#TRPBF
3265
18-Lead (5mm × 3mm) Plastic DFN
–40°C to 125°C
LTC3265HDHC#PBF
LTC3265HDHC#TRPBF
3265
18-Lead (5mm × 3mm) Plastic DFN
–40°C to 150°C
LTC3265MPDHC#PBF
LTC3265MPDHC#TRPBF
3265
18-Lead (5mm × 3mm) Plastic DFN
–55°C to 150°C
LTC3265EFE#PBF
LTC3265EFE#TRPBF
LTC3265
20-Lead Plastic TSSOP
–40°C to 125°C
LTC3265IFE#PBF
LTC3265IFE#TRPBF
LTC3265
20-Lead Plastic TSSOP
–40°C to 125°C
LTC3265HFE#PBF
LTC3265HFE#TRPBF
LTC3265
20-Lead Plastic TSSOP
–40°C to 150°C
LTC3265MPFE#PBF
LTC3265MPFE#TRPBF
LTC3265
20-Lead Plastic TSSOP
–55°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on nonstandard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
3265fa
2
For more information www.linear.com/LTC3265
LTC3265
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN_P = VIN_N = EN+ = EN– = 10V, MODE = 0V, RT = 200kΩ
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Boost Charge Pump
VIN_P
VIN_P Input Voltage Range
VUVLO
VIN_P Undervoltage Lockout Threshold
VIN_P Rising
VIN_P Falling
IVIN_P
VIN_P Quiescent Current
Shutdown, EN+ = EN– = 0V
MODE = VIN_P, EN– = 0V, IVOUT+ = ILDO+ = 0mA
MODE = VIN_P, IVOUT = ILDO+ = ILDO– = 0mA
MODE = 0V, IVOUT+ = 0mA
VRT
RT Regulation Voltage
+
+ Regulation Voltage
VOUT
VOUT
MODE = 10V
MODE = 0V
fOSC
Oscillator Frequency
RT = GND
ROUTBST
Boost Charge Pump Output Impedance
MODE = 0V, RT = GND
+ Short-Circuit Current
VOUT
+ = GND
l
4.5
l
l
3.4
450
16
V
3.8
3.6
4
V
V
3
85
110
3
6
170
220
6
1.200
V
2 • 0.94 • VIN_P
2 • VIN_P
V
V
500
550
32
IVOUT+(SC)
Max IVOUT
VMODE(H)
MODE Threshold Rising
l
VMODE(L)
MODE Threshold Falling
l
IMODE
MODE Pin Internal Pull-Down Current
l
100
0.4
VIN_P = MODE = 16V
µA
µA
µA
mA
kHz
Ω
220
300
1.1
2
mA
V
1.0
V
0.7
µA
Inverting Charge Pump
VIN_N
VIN_N Input Voltage Range
l
IVIN_N
VIN_N Quiescent Current
Shutdown, EN– = 0V
VOUT–
VOUT– Regulation Voltage
MODE = 10V
MODE = 0V
ROUTINV
Inverting Charge Pump Output
Impedance
MODE = 0V, RT = GND
IVOUT–(SC)
Max IVOUT– Short-Circuit Current
VOUT– = GND, |IVOUT–|
4.5
1
25
3
MODE = VIN_P, IVOUT – = ILDO– = 0mA
MODE = 0V, IVOUT – = 0mA
l
100
32
V
3
50
5
µA
µA
mA
–0.94 • VIN_N
–VIN_N
V
V
32
Ω
160
250
mA
32
V
1.200
1.224
V
Positive Regulator
LDO+ Output Voltage Range
+
VADJ
ADJ+ Reference Voltage
IADJ
ADJ+ Input Current
ILDO+(SC)
LDO+ Short-Circuit Current
+
ILDO+ = 1mA
l
1.2
l
1.176
+ = 1.2V
VADJ
–50
l
50
Line Regulation
Load Regulation
VDROPOUT+
ILDO+ = 50mA
Output Voltage Noise
CBYP+ = 100nF
VEN (H)
EN+ Threshold Falling
l
EN+ Pin Internal Pull-Down Current
IEN
mV/V
VIN_P
mV/mA
800
100
VEN+(L)
+
0.04
400
l
1.1
0.4
= EN+ = 16V
nA
mA
0.03
LDO+ Dropout Voltage
EN+ Threshold Rising
+
50
100
mV
µVRMS
2
V
1.0
V
0.7
µA
Negative Regulator
LDO– Output Voltage Range
VADJ
ADJ– Reference Voltage
ILDO– = –1mA
IADJ–
ADJ– Input Current
VADJ– = –1.2V
ILDO–(SC)
LDO– Short-Circuit Current
|ILDO–|
–
l
–32
l
–1.224
–1.2
–1.200
–50
l
50
100
V
–1.176
V
50
nA
mA
3265fa
For more information www.linear.com/LTC3265
3
LTC3265
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN_P = VIN_N = EN+ = EN– = 10V, MODE = 0V, RT = 200kΩ
SYMBOL
VDROPOUT–
PARAMETER
CONDITIONS
MIN
0.002
mV/V
0.02
mV/mA
LDO– Dropout Voltage
ILDO– = –50mA
200
Output Voltage Noise
CBYP– = 100nF
100
VEN–(L)
IEN–
EN– Threshold Falling
VIN_P = VIN_N = EN– = 16V
TYPICAL PERFORMANCE CHARACTERISTICS
600
500
500
OSCILLATOR FREQUENCY (kHz)
600
RT = GND
400
300
RT = 200kΩ
100
8
10
12
INPUT VOLTAGE (V)
14
16
3265 G01
Oscillator Frequency vs RT
2
V
1.0
V
0.7
µA
Shutdown Current vs Temperature
25
400
300
200
100
0
mV
µVRMS
TA = 25°C, CBST = CINV = 1µF, CIN_P = CIN_N =
SHUTDOWN CURRENT (μA)
Oscillator Frequency
vs Supply Voltage
500
maximum ambient temperature consistent with these specifications is
determined by specific operating conditions in conjunction with board
layout, the rated package thermal impedance and other environmental
factors.
The junction temperature (TJ, in °C) is calculated from the ambient
temperature (TA, in °C) and power dissipation (PD, in Watts) according to
the formula:
TJ = TA + (PD • θJA),
where θJA is the package thermal impedance.
Note 3: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperatures will exceed 150°C when overtemperature protection is
active. Continuous operation above the specified maximum operating
junction temperature may result in device degradation or failure.
COUT+ = COUT– = CLDO+ = CLDO– = 10µF, unless otherwise noted.
6
0.4
l
EN– Pin Internal Pull-Down Current
200
1.1
l
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC3265 is tested under pulsed load conditions such that
TJ ≈ TA. The LTC3265E is guaranteed to meet specifications from
0°C to 85°C junction temperature. Specifications over the –40°C to
125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LTC3265I is guaranteed over the –40°C to 125°C operating junction
temperature range, the LTC3265H is guaranteed over the –40°C to 150°C
operating junction temperature range and the LTC3265MP is guaranteed
over the –55°C to 150°C operating junction temperature range. High
junction temperatures degrade operating lifetimes; operating lifetime
is derated for junction temperatures greater than 125°C. Note that the
OSCILLATOR FREQUENCY (kHz)
UNITS
Load Regulation
EN– Threshold Rising
4
MAX
Line Regulation
VEN–(H)
0
TYP
VIN_P = VIN_N
20
15
10V
10
16V
5
4.5V
1
10
100
RT (kΩ)
1k
10k
3265 G02
0
–50
0
50
100
TEMPERATURE (°C)
150
3265 G03
3265fa
4
For more information www.linear.com/LTC3265
LTC3265
TYPICAL
PERFORMANCE
CHARACTERISTICS
+
–
+
–
TA = 25°C, CBST = CINV = 1µF, CIN_P = CIN_N =
COUT = COUT = CLDO = CLDO = 10µF, unless otherwise noted.
10
9
EN+ = EN– = 10V
EN– = 10V
100
EN+ = 10V
50
RT = GND
10
8
7
6
5
RT = 200kΩ
4
3
2
0
–50
0
50
100
TEMPERATURE (°C)
0
150
4
6
8
10
12
INPUT VOLTAGE (V)
3265 G04
12
10
8
RT = 200kΩ
6
4
RT = 1.2MΩ
2
0
–50
0
50
100
TEMPERATURE (°C)
150
2.5
2.0
RT = 1.2MΩ
1.5
1.0
0.5
RT = GND
0
0.1
1
10
LOAD CURRENT (mA)
100
3265 G10
4
6
8
10
12
INPUT VOLTAGE (V)
14
30
VOUT+ Short-Circuit Current
vs Supply Voltage
VIN_P = 4.5V
VIN_P = 10V
25
20
15
10
VIN_P = 16V
5
0
–50
0
50
100
TEMPERATURE (°C)
RT = GND
200
150
100
RT = 200kΩ
50
0
150
4
6
40
30
VIN_N = 4.5V
VIN_N = 16V
20
VIN_N = 10V
10
5
0
–50
180
50
100
TEMPERATURE (°C)
150
3265 G11
RT = GND
160
140
120
100
80
RT = 200kΩ
60
40
20
0
0
16
200
25
15
14
VOUT– Short-Circuit Current
vs Supply Voltage
RT = GND
35
8
10
12
SUPPLY VOLTAGE (V)
3265 G09
VOUT– Effective Open-Loop
Resistance vs Temperature
45
16
3265 G06
3265 G08
VOUT– EFFECTIVE OPEN-LOOP RESISTANCE (Ω)
(2 • VIN_P– VOUT+) VOLTAGE (V)
RT = 200kΩ
RT = 1.2MΩ
250
35
VOUT+ Voltage Loss vs Output
Current (Constant Frequency Mode)
VIN_P = 10V
0
16
40
3265 G07
3.0
14
VOUT+ SHORT-CIRCUIT CURRENT (mA)
RT = GND
RT = 200kΩ
4
VOUT+ Effective Open-Loop
Resistance vs Temperature
VOUT+ EFFECTIVE OPEN-LOOP RESISTANCE (Ω)
QUIESCENT CURRENT (mA)
14
VIN_P = VIN_N = 10V, EN+ = EN– = 10V
6
3265 G05
Quiescent Current vs Temperature
(Constant Frequency Mode)
16
RT = GND
8
2
RT = 1.2MΩ
1
VOUT– SHORT–CIRCUIT CURRENT (mA)
200
150
12
QUIESCENT CURRENT (mA)
VIN_P = VIN_N = 10V, MODE = H
QUIESCENT CURRENT (mA)
QUIESCENT CURRENT (μA)
250
Inverting Charge Pump Quiescent
Current vs Supply Voltage (Constant
Frequency Mode)
Boost Charge Pump Quiescent
Current vs Supply Voltage (Constant
Frequency Mode)
Quiescent Current vs Temperature
(Burst Mode Operation)
4
6
8
10
12
SUPPLY VOLTAGE (V)
14
16
3265 G12
3265fa
For more information www.linear.com/LTC3265
5
LTC3265
TYPICAL
PERFORMANCE
CHARACTERISTICS
+
–
+
–
COUT = COUT = CLDO = CLDO = 10µF, unless otherwise noted.
VOUT– Voltage Loss vs Output
Current (Constant Frequency Mode)
1.224
RT = 200kΩ
2.5
1.216
2.0
1.208
1.5
RT = 1.2MΩ
1.0
0.5
RT = GND
1.200
1.192
1.176
–50
100
0
3265 G13
50
100
TEMPERATURE (°C)
200
0
–50
150
ADJ+ VOLTAGE (V)
1.195
250
–1.192
–1.200
–1.208
–1.216
100
–1.224
–50
3265 G16
0
50
100
TEMPERATURE (°C)
LDO– Load Regulation
150
200
150
100
50
0
–50
0
50
100
TEMPERATURE (°C)
150
3265 G18
LDO+ Rejection of VOUT+ Ripple
–1.195
150
VIN_N = 10V
ILDO– = –50mA
3265 G17
–1.190
VIN_N = 10V
UNITY GAIN
50
100
TEMPERATURE (°C)
LDO– Dropout Voltage
vs Temperature
VIN_N = 10V
IOUT– = –1mA
–1.184
1.205
1.200
0
3265 G15
–1.176
VIN_P = 10V
UNITY GAIN
LDO– VOLTAGE (V)
300
ADJ– Pin Voltage vs Temperature
1.210
1
10
LOAD CURRENT (mA)
400
3265 G14
LDO+ Load Regulation
1.190
0.1
500
100
LDO– DROPOUT VOLTAGE (V)
1
10
LOAD CURRENT (mA)
VIN_P = 10V
ILDO+ = 50mA
600
1.184
0
0.1
LDO+ VOLTAGE (V)
700
VIN_P = 10V
ILDO+ = 1mA
LDO+ DROPOUT VOLTAGE (V)
VIN_P = VIN_N = 10V
LDO+ Dropout Voltage
vs Temperature
ADJ+ Pin Voltage vs Temperature
ADJ+ VOLTAGE (V)
(VIN_N–|VOUT–|) VOLTAGE (V)
3.0
TA = 25°C, CBST = CINV = 1µF, CIN_P = CIN_N =
LDO– Rejection of VOUT– Ripple
VLDO+
10mV/DIV
AC-COUPLED
VLDO–
10mV/DIV
AC-COUPLED
VOUT+
10mV/DIV
AC-COUPLED
VOUT–
10mV/DIV
AC-COUPLED
–1.200
–1.205
–1.210
0.1
1
10
LOAD CURRENT (mA)
100
VIN_P = 10V
VLDO+ = 5V
fOSC = 500kHz
ILDO+ = 50mA
1µs/DIV
3265 G20
VIN_N = 10V
VLDO– = –5V
fOSC = 500kHz
ILDO– = –50mA
1µs/DIV
3265 G21
3265 G19
3265fa
6
For more information www.linear.com/LTC3265
LTC3265
TYPICAL
PERFORMANCE
CHARACTERISTICS
+
–
+
–
COUT = COUT = CLDO = CLDO = 10µF, unless otherwise noted.
TA = 25°C, CBST = CINV = 1µF, CIN_P = CIN_N =
LDO+ Load Transient
LDO– Load Transient
VLDO+
10mV/DIV
AC-COUPLED
VLDO–
10mV/DIV
AC-COUPLED
20mA
ILDO+
2mA
–2mA
ILDO–
–20mA
VIN_P = 10V
VLDO+ = 5V
VIN_N = 10V
VLDO– = –5V
3265 G22
40µs/DIV
VOUT+ Transient (Burst Mode
Operation, MODE = H)
VOUT+
1V/DIV
AC-COUPLED
50mA
IOUT+
5mA
MODE
3265 G24
2ms/DIV
3265 G23
VOUT+ Transient
(MODE = Low to High)
VOUT+
500mV/DIV
AC-COUPLED
VIN_P = 10V
fOSC = 500kHz
40µs/DIV
VIN_P = 10V
fOSC = 500kHz
IOUT+ = 5mA
2ms/DIV
3265 G25
VOUT– Transient
(MODE = Low to High)
VOUT– Transient (Burst Mode
Operation, MODE = H)
VOUT–
500mV/DIV
AC-COUPLED
VOUT–
500mV/DIV
AC-COUPLED
–5mA
IOUT–
–50mA
MODE
VIN_N = 10V
fOSC = 500kHz
2ms/DIV
3265 G26
VIN_N = 10V
fOSC = 500kHz
IOUT– = –5mA
2ms/DIV
3265 G27
3265fa
For more information www.linear.com/LTC3265
7
LTC3265
PIN FUNCTIONS
(DFN/TSSOP)
CBST– (Pin 1/Pin 2): Boost Charge Pump Flying Capacitor
Negative Connection.
NC (Pins 1, 11 TSSOP Only): No Connect. These pins are
not connected to LTC3265 die. These pins should be left
floating or connected to ground.
CBST+ (Pin 2/Pin 3): Boost Charge Pump Flying Capacitor
Positive Connection.
VIN_P (Pin 3/Pin 4): Input Voltage for Boost Charge Pump.
VIN_P should be bypassed with a low impedance ceramic
capacitor.
EN– (Pin 4/Pin 5): Logic Input. A logic “high” on the
EN– pin enables the inverting charge pump as well as the
negative LDO regulator. Do not float this pin.
BYP– (Pin 5/Pin 6): LDO– Reference Bypass Pin. Connect
a capacitor from BYP– to GND to reduce LDO– output
noise. Leave floating if unused.
ADJ– (Pin 6/Pin 7): Feedback Input for the Negative Low
Dropout Regulator. This pin servos to a fixed voltage of
–1.2V when the control loop is complete.
LDO– (Pin 7/Pin 8): Negative Low Dropout (LDO–) Linear
Regulator Output. This pin requires a low ESR (equivalent
series resistance) capacitor with at least 2µF capacitance
to ground for stability.
VOUT– (Pin 8/Pin 9): Inverting Charge Pump Output Voltage.
In constant frequency mode (MODE = low) this pin is driven
to –VIN_N. In Burst Mode operation, (MODE = high) this
pin voltage is regulated to – 0.9 • VIN_N using an internal
burst comparator with hysteretic control.
CINV– (Pin 9/Pin 10): Inverting Charge Pump Flying
Capacitor Positive Connection.
CINV+ (Pin 10/Pin 12): Inverting Charge Pump Flying
Capacitor Negative Connection.
VIN_N (Pin 11/Pin 13): Input Voltage for Inverting Charge
Pump. This pin should be tied to VIN_P or VOUT+ pins
depending on the desired output voltage at the VOUT– pin.
If VIN_N is tied to VOUT+, the output at VOUT– will be –VOUT+
or –2 • VIN_P. This configuration is suitable for symmetric
outputs at LDO+ and LDO– pins. If VIN_N is tied to VIN_P,
the output at VOUT– will be –VIN_P. This configuration is
suitable for asymmetric outputs at LDO+ and LDO– pins. See
Applications Information for additional details. VIN_N should
be bypassed with a low impedance ceramic capacitor.
RT (Pin 12/Pin 14): Input Connection for Programming
the Switching Frequency. The RT pin servos to a fixed
1.2V when the EN+ or EN– pin is driven to a logic “high”.
A resistor from RT to GND sets the charge pump switching frequency. If the RT pin is tied to GND, the switching
frequency defaults to a fixed 500kHz.
EN+ (Pin 13/Pin 15): Logic Input. A logic “high” on the
EN+ pin enables the boost charge pump as well as the
positive LDO regulator. Do not float this pin.
MODE (Pin 14/Pin 16): Logic Input. The MODE pin
determines the charge pump operating mode. A logic “high”
on the MODE pin forces the charge pumps to operate in
Burst Mode operation. The boost charge pump regulates
the VOUT+ pin to 0.94 • 2 • VIN_P with hysteretic control.
The inverting charge pump regulates the VOUT– pin to
(–0.94 • VIN_N). A logic “low” on the MODE pin forces
the charge pumps to operate in open-loop mode with a
constant switching frequency. The boost charge pump
doubles the input to 2 • VIN_P in this mode while the
inverting charge pump inverts its input to (–VIN_N). The
switching frequency in both modes is determined by an
external resistor from the RT pin to GND. In Burst Mode
operation, this represents the frequency of the burst cycles
before the part enters the low quiescent current sleep state.
Do not float this pin.
3265fa
8
For more information www.linear.com/LTC3265
LTC3265
PIN FUNCTIONS
(DFN/TSSOP)
BYP+ (Pin 15/Pin 17): LDO+ Reference Bypass Pin. Connect a capacitor from BYP+ to GND to reduce LDO+ output
noise. Leave floating if unused.
ADJ+ (Pin 16/Pin 18): Feedback Input for the Positive
Low Dropout (LDO+) Regulator. This pin servos to a fixed
voltage of 1.2V when the control loop is complete.
LDO+ (Pin 17/Pin 19): Positive Low Dropout (LDO+) Output.
This pin requires a low ESR capacitor with at least 2µF
capacitance to ground for stability.
VOUT+ (Pin 18/Pin 20): Boost Charge Pump Output Voltage.
In constant frequency mode (MODE = low) this pin is driven
to 2 • VIN_P. In Burst Mode operation, (MODE = high) this
pin voltage is regulated to 0.94 • 2 • VIN_P using an internal
burst comparator with hysteretic control.
GND (Exposed Pad Pin 19/Exposed Pad Pin 21): Ground.
The exposed package pad is ground and must be soldered
to the PC board ground plane for proper functionality and
for rated thermal performance.
3265fa
For more information www.linear.com/LTC3265
9
LTC3265
BLOCK DIAGRAM
Note: Pin numbers are as per DFN package. Refer to the Pin Functions section for corresponding TSSOP pin numbers.
2
1
CBST +
3
18
CBST –
VOUT+
VIN_P
S1
S4
S3
S2
BOOST
CHARGE PUMP
LDO+
13
4
14
EN+
EN–
MODE
50kHz
TO
500kHz
OSC
CHARGE
PUMP
AND
LOGIC
INPUT
BYP+
9
8
16
15
1.2V
REF
–1.2V
REF
BYP–
VIN_N
ADJ–
–
S5
10
+
ADJ+
INVERTING
CHARGE PUMP
11
–
17
CINV +
5
6
+
12
RT
S7
CINV –
S6
VOUT–
S8
LDO–
7
GND
19
3265 BD
3265fa
10
For more information www.linear.com/LTC3265
LTC3265
OPERATION (Refer to the Block Diagram)
Shutdown Mode
In shutdown mode, all circuitry except the internal bias
is turned off. The LTC3265 is in shutdown when a logic
low is applied to both the enable inputs (EN+ and EN–).
The LTC3265 only draws 3µA (typ) from the VIN_P supply
in shutdown. If the VIN_N pin is tied to VIN_P it draws an
additional 1µA (typ) in shutdown. If the VIN_N pin is tied
to VOUT+ then it does not carry any additional current in
shutdown.
Boost Charge Pump Constant Frequency Operation
The LTC3265 boost charge pump provides low noise
constant frequency operation when a logic low is applied
to the MODE pin. The boost charge pump and oscillator
circuit are enabled using the EN+ pin. At the beginning of
a clock cycle, switches S1 and S2 are closed. The external
flying capacitor across CBST+ and CBST– pins is charged
to the VIN_P supply. In the second phase of the clock cycle,
switches S1 and S2 are opened, while switches S3 and
S4 are closed. In this configuration the CBST– side of
the flying capacitor is connected to VIN_P and charge is
delivered through the CBST+ pin to VOUT+. In steady state
the VOUT+ pin regulates at 2 • VIN_P less any voltage drop
due to the load current on VOUT+.
Boost Charge Pump Burst Mode Operation
The LTC3265 boost charge pump provides low power
Burst Mode operation when a logic high is applied to the
MODE pin. In Burst Mode operation, the boost charge
pump charges the VOUT+ pin to 0.94 • 2 • VIN_P (typ). The
part then shuts down the internal oscillator to reduce
switching losses and goes into a low current state. This
state is referred to as the sleep state in which the part
consumes only about 85µA from the VIN_P pin. When
the output voltage droops enough to overcome the burst
comparator hysteresis, the part wakes up and commences
boost charge pump cycles until VOUT+ output voltage
exceeds –0.94 • 2 • VIN_P (typ). This mode provides lower
operating current at the cost of higher output ripple and
is ideal for light load operation.
Inverting Charge Pump Constant Frequency Operation
The LTC3265 inverting charge pump provides low noise
constant frequency operation when a logic low is applied
to the MODE pin. The inverting charge pump and oscillator
circuit are enabled using the EN– pin. At the beginning of
a clock cycle, switches S5 and S6 are closed. The external
flying capacitor across CINV+ and CINV– pins is charged
to the VIN_N pin voltage. The VIN_N pin must be tied to
VIN_P or VOUT+ pins depending on the desired output
voltage at the VOUT– pin. In the second phase of the clock
cycle, switches S5 and S6 are opened, while switches S7
and S8 are closed. In this configuration the CINV+ side of
the flying capacitor is grounded and charge is delivered
through the CINV– pin to VOUT–. In steady state the VOUT–
pin regulates at –VIN_N less any voltage drop due to the
load current on VOUT–.
Inverting Charge Pump Burst Mode Operation
The LTC3265 inverting charge pump provides low power
Burst Mode operation when a logic high is applied to
the MODE pin. In Burst Mode, the charge pump charges
the VOUT– pin to –0.94 • VIN_N (typ). The part then shuts
down the internal oscillator to reduce switching losses
600
OSCILLATOR FREQUENCY (kHz)
The LTC3265 is a high voltage low noise dual output
regulator. It includes a boost charge pump, an inverting
charge pump and two LDO regulators to generate bipolar
low noise supply rails from a single positive input. It supports a wide input power supply range from 4.5V to 16V
for the boost charge pump and a 4.5V to 32V range for
the inverting charge pump.
500
400
300
200
100
0
1
10
100
RT (kΩ)
1k
10k
3265 F01
Figure 1. Oscillator Frequency vs RT
3265fa
For more information www.linear.com/LTC3265
11
LTC3265
OPERATION (Refer to the Block Diagram)
and goes into a low current state. This state is referred to
as the sleep state in which the IC consumes only about
25µA from the VIN_N pin. When the VOUT– output voltage
droops enough to overcome the burst comparator hysteresis, the part wakes up and commences charge pump
cycles until the output voltage exceeds –0.94 • VIN (typ).
This mode provides lower operating current at the cost of
higher output ripple and is ideal for light load operation.
Charge Pump Frequency Programming
The charge transfer frequency can be adjusted between
50kHz and 500kHz using an external resistor on the RT
pin. At slower frequencies the effective open-loop output
resistance (ROL) of the charge pumps are larger and they
provide smaller average output current. Figure 1 can be
used to determine a suitable value of RT to achieve a required oscillator frequency. If the RT pin is grounded, the
part operates at a constant frequency of 500kHz.
The charge pumps have lower ROL at higher frequencies.
For Burst Mode operation it is recommended that the RT
pin be tied to GND. This minimizes the charge pump ROL,
quickly charges the output up to the burst threshold and
optimizes the duration of the low current sleep state.
Charge Pump Soft-Start
The LTC3265 has built in soft-start circuitry to prevent
excessive current flow during start-up. The soft-start is
achieved by internal circuitry that slowly ramps the amount
of current available at the output storage capacitors on the
VOUT+ and VOUT– pins. The soft-start circuitry is reset in the
event of a commanded shutdown or thermal shutdown.
Charge Pump Short-Circuit/Thermal Protection
The LTC3265 charge pumps have built-in short-circuit
current limit as well as overtemperature protection.
During a short-circuit condition, the part automatically
limits its output currents from the VOUT+ and VOUT– pins to
220mA and 160mA respectively. If the junction temperature exceeds approximately 175°C the thermal shutdown
circuitry disables current delivery to the outputs. Once
the junction temperature drops back to approximately
165°C current delivery to the outputs is resumed. When
thermal protection is active the junction temperature is
beyond the specified operating range. Thermal protection
is intended for momentary overload conditions outside
normal operation. Continuous operation above the specified maximum operating junction temperature may impair
device reliability.
Positive Low Dropout Linear Regulator (LDO+)
The positive low dropout regulator (LDO+) supports a load
of up to 50mA. The LDO+ takes power from the VOUT+ pin
(output of the boost charge pump) and drives the LDO+
output pin to a voltage programmed by the resistor divider
connected between LDO+, ADJ+ and GND pins. For stability, the LDO+ output must be bypassed to ground with a
low ESR ceramic capacitor that maintains a capacitance
of at least 2µF across operating temperature and voltage.
The boost charge pump and LDO+ are enabled or disabled
via the EN+ logic input pin. Internal circuitry delays enabling
the LDO+ output until reasonable voltage has developed on
the charge storage capacitor on the VOUT+ pin. When the
LDO+ is enabled, a soft-start circuit ramps its regulation
point from zero to the final value over a period of 75µs,
reducing the inrush current on VOUT+ pin.
Figure 2 shows the LDO+ regulator application circuit.
The LDO+ output voltage VLDO+ can be programmed by
choosing suitable values of R1 and R2 such that:
 R1 
VLDO + = 1.2V •  +1
 R2 
An optional capacitor of 100nF can be connected from the
BYP+ pin to ground. This capacitor bypasses the internal
1.2V reference of the LTC3265 and improves the noise
performance of the LDO+. If this function is not used the
BYP+ pin should be left floating.
An optional feedback capacitor (COPT) can be added for
improved transient response. A value of 10pF is recommended for most applications but experimentation with
capacitor sizes between 2pF and 22pF may yield further
improvement in the transient response.
3265fa
12
For more information www.linear.com/LTC3265
LTC3265
OPERATION
negative by the charge pump circuitry. Soft-start circuitry
in the charge pump also provides soft-start functionality
for the LDO– and prevents excessive inrush currents.
VOUT+
EN+
0
LDO+
1
ADJ+
COPT
BYP+
1.2V REF
GND
CBYP+
R1
COUT
LDO
OUTPUT
R2
Figure 3 shows the LDO– regulator application circuit.
The LDO– output voltage VLDO– can be programmed by
choosing suitable values of R1 and R2 such that:
3265 F02
Figure 2. Positive LDO Application Circuit
Negative Low Dropout Linear Regulator (LDO–)
The negative low dropout regulator (LDO–) supports a
load of up to 50mA. The LDO– takes power from the VOUT–
pin (output of the inverting charge pump) and drives the
LDO– output pin to a voltage programmed by the resistor
divider connected between LDO–, ADJ– and GND pins. For
stability, the LDO– output must be bypassed to ground with
a low ESR ceramic capacitor that maintains a capacitance
of at least 2µF across operating temperature and voltage.
 R1 
VLDO – = – 1.2V •  +1
 R2 
An optional capacitor of 100nF can be connected from the
BYP – pin to ground. This capacitor bypasses the internal
–1.2V reference of the LTC3265 and improves the noise
performance of the LDO–. If this function is not used the
BYP – pin should be left floating.
An optional feedback capacitor (COPT) can be added for
improved transient response. A value of 10pF is recommended for most applications but experimentation with
capacitor sizes between 2pF and 22pF may yield further
improvement in the transient response.
The LDO– is enabled or disabled via the EN– logic input
pin. Initially, when the EN– logic input is low, the charge
pump circuitry is disabled and the VOUT– pin is at GND.
When EN– is switched high, the VOUT– pin will be driven
–1.2V REF
GND
CBYP–
BYP–
ADJ–
EN–
1
COPT
LDO–
R2
R1
COUT
LDO
OUTPUT
0
VOUT–
3265 F03
Figure 3: Negative LDO Application Circuit
3265fa
For more information www.linear.com/LTC3265
13
LTC3265
APPLICATIONS INFORMATION
Effective Open-Loop Output Resistance
The effective open-loop output resistance (ROL) of a charge
pump is a very important parameter which determines the
strength of the charge pump. The value of this parameter
depends on many factors such as the oscillator frequency
(fOSC), value of the flying capacitor (CFLY), the nonoverlap
time, the internal switch resistances (RS) and the ESR of
the external capacitors.
Typical ROL values of the boost charge pump as a function
of temperature are shown in Figure 4.
VOUT+ EFFECTIVE OPEN-LOOP RESISTANCE (Ω)
Typical ROL values of the inverting charge pump as a
function of temperature are shown in Figure 5.
40
35
30
RT = GND
VIN_P = 4.5V
IOUT +
VRIPPLE(P−P) ≈
COUT +
VIN_P = 10V
25
15
VIN_P = 16V
5
0
–50
0
50
100
TEMPERATURE (°C)
150
3265 F04
VOUT+ EFFECTIVE OPEN-LOOP RESISTANCE (Ω)
Figure 4. Typical ROL vs Temperature (Boost Charge Pump)
45
40
RT = GND
35
30
VIN_N = 4.5V
25
VIN_N = 16V
20
15
VIN_N = 10V
10
Just as the value of COUT controls the amount of output
ripple, the value of CIN controls the amount of ripple present
at the input pins (VIN_P and VIN_N). The amount of bypass
capacitance required at the input depends on the source
impedance driving VIN_P and VIN_N. For best results it is
recommended that VIN_P and VIN_N be bypassed with at
least 2µF of low ESR capacitance. A high ESR capacitor
such as tantalum or aluminum will have higher input
noise than a low ESR ceramic capacitor. Therefore, a
ceramic capacitor is recommended as the main bypass
capacitance with a tantalum or aluminum capacitor used
in parallel if desired.
Flying Capacitor Selection
5
0
–50
 1

– tON 
f
 OSC

where fOSC is the oscillator frequency, COUT+ is the value of
the output capacitor and tON is the on-time of the oscillator
(1µs typical). The output ripple at the VOUT– pin can be
calculated using the corresponding IOUT– and COUT– values.
20
10
control loop stability, output ripple, charge pump strength
and minimum turn-on time. To reduce noise and ripple, it
is recommended that low ESR ceramic capacitors be used
for the charge pumps and LDO outputs. All capacitors
should retain at least 2µF of capacitance over operating
temperature and bias voltage. Tantalum and aluminum
capacitors can be used in parallel with a ceramic capacitor
to increase the total capacitance but should not be used
alone because of their high ESR. In constant frequency
mode, the values of COUT+ and COUT– directly control the
amount of output ripple for a given load current. Increasing
the sizes of COUT+ and COUT– will reduce the output ripple
at the expense of higher minimum turn-on time. The peakto-peak output ripple at the VOUT+ pin is approximately
given by the expression:
0
50
100
TEMPERATURE (°C)
150
3265 F05
Figure 5. Typical ROL vs Temperature (Inverting Charge Pump)
Input/Output Capacitor Selection
The style and value of capacitors used with the LTC3265
determine several important parameters such as regulator
The flying capacitors (CBST and CINV) controls the strength
of the charge pumps. A 1µF or greater ceramic capacitor is suggested for the flying capacitor for applications
requiring the full rated output current of the charge pump.
For very light load applications, the flying capacitor may
be reduced to save space or cost. For example, a 0.2µF
capacitor might be sufficient for load currents up to 20mA.
3265fa
14
For more information www.linear.com/LTC3265
LTC3265
APPLICATIONS INFORMATION
A smaller flying capacitor leads to a larger effective openloop resistance (ROL) and thus limits the maximum load
current that can be delivered by the charge pump.
VOUT+
VIN_P
CBST
LDO+
Ceramic Capacitors
Ceramic capacitors of different materials lose their capacitance with higher temperature and voltage at different rates.
For example, a capacitor made of X5R or X7R material
will retain most of its capacitance from –40°C to 85°C
whereas a Z5U or Y5V style capacitor will lose considerable
capacitance over that range. Z5U and Y5V capacitors may
also have a poor voltage coefficient causing them to lose
60% or more of their capacitance when the rated voltage
is applied. Therefore when comparing different capacitors,
it is often more appropriate to compare the amount of
achievable capacitance for a given case size rather than
discussing the specified capacitance value. The capacitor
manufacturer’s data sheet should be consulted to ensure
the desired capacitance at all temperatures and voltages.
Table 1 is a list of ceramic capacitor manufacturers and
their websites.
Table 1
CBYP–
RT
LDO–
CINV
CBYP+
VIN_N
VOUT–
3265 F06
Figure 6. Recommended Layout
Thermal Management
At high input voltages and maximum output current, there
can be substantial power dissipation in the LTC3265. If
the junction temperature increases above approximately
175°C, the thermal shutdown circuitry will automatically
deactivate the output. To reduce the maximum junction
temperature, a good thermal connection to the PC board
ground plane is recommended. Connecting the exposed pad
of the package to a ground plane under the device on two
layers of the PC board can reduce the thermal resistance
of the package and PC board considerably.
AVX
www.avx.com
Kemet
www.kemet.com
Murata
www.murata.com
Taiyo Yuden
www.t-yuden.com
Vishay
www.vishay.com
TDK
www.component.tdk.com
Derating Power at High Temperatures
Würth Elektronik
www.we-online.com
To prevent an overtemperature condition in high power
applications, Figure 7 should be used to determine the
maximum combination of ambient temperature and power
dissipation.
Layout Considerations
Due to high switching frequency and high transient currents
produced by LTC3265, careful board layout is necessary
for optimum performance. A true ground plane and short
connections to all the external capacitors will improve
performance and ensure proper regulation under all conditions. Figure 6 shows an example layout for the LTC3265.
The flying capacitor nodes CBST+, CBST–, CINV+ and CINV–
switch large currents at a high frequency. These nodes
should not be routed close to sensitive pins such as the
LDO feedback pins (ADJ+ and ADJ–) and internal reference
bypass pins (BYP+ and BYP–).
The power dissipated in the LTC3265 should always fall
under the line shown for a given ambient temperature. The
power dissipated in the LTC3265 has four components.
Power dissipated in boost charge pump:
PBOOST = (2 • VIN_P – VOUT+) • (IOUT+ + ILDO+)
Power dissipated in the positive LDO:
PLDO+ = (VOUT+ – VLDO+) • ILDO+
3265fa
For more information www.linear.com/LTC3265
15
LTC3265
APPLICATIONS INFORMATION
Power dissipated in the negative LDO:
It is recommended that the LTC3265 be operated in the
region corresponding to TJ ≤ 150°C for continuous operation as shown in Figure 7. Operation beyond 150°C
should be avoided as it may degrade part performance
and lifetime. At high temperatures, typically around 175°C,
the part is placed in thermal shutdown and all outputs are
disabled. When the part cools back down to a low enough
temperature, typically around 165°C, the outputs are
re-enabled and the part resumes normal operation.
PLDO– = (|VOUT–| – |VLDO–|) • ILDO–
And, power dissipated in the inverting charge pump:
PINV = (VIN_N – |VOUT–|) • (IOUT– + ILDO–)
where IOUT+ denotes any additional current that might be
pulled directly from the VOUT+ pin and IOUT– denotes any
additional current out of the VOUT– pin. The LDO+ current
is supplied by the boost charge pump through VOUT+ and
is therefore included in the boost charge pump power
dissipation. The LDO– current is supplied by the inverting
charge pump through VOUT– and is therefore included in
the inverting charge pump power dissipation.
MAXIMUM POWER DISSIPATION (W)
7
The total power dissipation of the LTC3265 is given by:
PD = PBOOST + PLDO+ + PLDO– + PINV
The derating curve in Figure 7 assumes a maximum thermal
resistance, θJA, of 38°C/W for the 20-lead TSSOP package. This can be achieved with a 4-layer PCB that includes
2oz Cu traces and six vias from the exposed pad of the
LTC3265 to the ground plane.
θJA = 38°C/W
6
THERMAL
SHUTDOWN
5
4
3
2
RECOMMENDED
OPERATION
1
TJ = 175°C
TJ = 150°C
0
–50 –25
0 25 50 75 100 125 150 175
AMBIENT TEMPERATURE (°C)
3265 F07
Figure 7. Maximum Power Dissipation vs Ambient Temperature
TYPICAL APPLICATIONS
Low Power ±20V Power Supply from a Single-Ended 15V Input Supply
1µF
CBST+ CBST –
VOUT+
VIN_N
15V
LDO+
VIN_P
10µF
+20V
10µF
LTC3265
1µF
10µF
EN+
EN–
ADJ+
BYP+
MODE
GND
CINV+
BYP–
CINV –
ADJ–
VOUT–
LDO–
100nF
787k
50k
100nF
50k
787k
10µF
–20V
10µF
RT
200k
3265 TA03
3265fa
16
For more information www.linear.com/LTC3265
LTC3265
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LTC3265#packaging for the most recent package drawings.
DHC Package
18-Lead Plastic DFN (5mm × 3mm)
(Reference LTC DWG # 05-08-1955 Rev Ø)
0.65 ±0.05
3.50 ±0.05
1.65 ±0.05
2.20 ±0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 ± 0.05
0.50 BSC
4.40 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
5.00 ±0.10
(2 SIDES)
R = 0.20
TYP
3.00 ±0.10
(2 SIDES)
R = 0.115
TYP
10
0.40 ±0.10
18
1.65 ±0.10
(2 SIDES)
PIN 1
TOP MARK
(SEE NOTE 6)
PIN 1
NOTCH
0.200 REF
0.75 ±0.05
0.00 – 0.05
9
0.25 ±0.05
0.50 BSC
4.40 ±0.10
(2 SIDES)
1
(DHC18) DFN 0713 REV Ø
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WJED-1) IN JEDEC
PACKAGE OUTLINE MO-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
3265fa
For more information www.linear.com/LTC3265
17
LTC3265
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LTC3265#packaging for the most recent package drawings.
FE Package
20-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1663 Rev K)
Exposed Pad Variation CA
6.07
(.239)
6.40 – 6.60*
(.252 – .260)
4.95
(.195)
4.95
(.195)
DETAIL A
1.98
(.078)
REF
20 1918 17 16 15 14 13 12 11
6.60 ±0.10
4.50 ±0.10
DETAIL A
2.74
(.108)
6.40
2.74
(.252)
(.108)
BSC
SEE NOTE 4
0.45 ±0.05
1.05 ±0.10
0.65 BSC
1 2 3 4 5 6 7 8 9 10
6.07
(.239)
RECOMMENDED SOLDER PAD LAYOUT
4.30 – 4.50*
(.169 – .177)
0.09 – 0.20
(.0035 – .0079)
0.25
REF
0.50 – 0.75
(.020 – .030)
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
3. DRAWING NOT TO SCALE
0.56
(.022)
REF
DETAIL A IS THE PART OF
THE LEAD FRAME FEATURE
FOR REFERENCE ONLY
NO MEASUREMENT PURPOSE
1.20
(.047)
MAX
0° – 8°
0.65
(.0256)
BSC
0.195 – 0.30
(.0077 – .0118)
TYP
0.05 – 0.15
(.002 – .006)
FE20 (CA) TSSOP REV K 0913
4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
3265fa
18
For more information www.linear.com/LTC3265
LTC3265
REVISION HISTORY
REV
DATE
DESCRIPTION
A
03/16
Changed conditions of RT in VOUT– Voltage Loss curve.
PAGE NUMBER
6
3265fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
For more
information
www.linear.com/LTC3265
19
LTC3265
TYPICAL APPLICATION
Low Noise +7V/–2V Power Supply from a Single-Ended 5V Input Supply (Frequency = 200kHz)
1µF
CBST+ CBST –
VOUT+
VIN_N
5V
LDO+
VIN_P
10µF
7V
10µF
LTC3265
1µF
10µF
EN+
EN–
ADJ+
BYP+
MODE
GND
CINV+
BYP–
CINV –
ADJ–
VOUT–
LDO–
100nF
497k
100k
100nF
100k
66.5k
10µF
–2V
10µF
RT
200k
3265 TA02
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1144
Switched-Capacitor Wide Input Range Voltage Converter with
Shutdown
Wide Input Voltage Range: 2V to 18V, ISD < 8µA,
SO8 Package
LTC1514/LTC1515
Step-Up/Step-Down Switched Capacitor DC/DC Converters
VIN: 2V to 10V, VOUT: 3.3V to 5V, IQ = 60µA, SO8 Package
LT 1611
150mA Output, 1.4MHz Micropower Inverting Switching Regulator
VIN: 0.9V to 10V, VOUT = ±34V, ThinSOT™ Package
LT1614
250mA Output, 600kHz Micropower Inverting Switching Regulator
VIN: 0.9V to 6V, VOUT = ±30V, IQ = 1mA,
MS8, SO8 Packages
LTC1911
250mA, 1.5MHz Inductorless Step-Down DC/DC Converter
VIN: 2.7V to 5.5V, VOUT = 1.5V/1.8V, IQ = 180µA,
MS8 Package
®
LTC3250/LTC3250-1.2 Inductorless Step-Down DC/DC Converter
LTC3250-1.5
VIN: 3.1V to 5.5V, VOUT = 1.2V, 1.5V, IQ = 35µA,
ThinSOT Package
LTC3251
500mA Spread Spectrum Inductorless Step-Down DC/DC Converter
VIN: 2.7V to 5.5V, VOUT: 0.9V to 1.6V, 1.2V, 1.5V,
IQ = 9µA, MS10E Package
LTC3252
Dual 250mA, Spread Spectrum Inductorless Step-Down DC/DC
Converter
VIN: 2.7V to 5.5V, VOUT: 0.9V to 1.6V, IQ = 50µA,
DFN12 Package
LT1054/LT1054L
Switched Capacitor Voltage Converter with Regulator
VIN: 3.5V to 15V/7V, IOUT = 100mA/125mA, N8, S08,
SO16 Packages
LTC3260
Low Noise Dual Supply Inverting Charge Pump
VIN: 4.5V to 32V, ILDO± = 50mA, DE14, MSE16 Packages
LTC3261
High Voltage, Low Quiescent Current Inverting Charge Pump
VIN: 4.5V to 32V, IOUT = 100mA, MSE12 Package
LTC3200/LTC3200-5
Low Noise Doubler Charge Pump
IOUT = 100mA, 2MHz Fixed Frequency, MS8 and ThinSOT
(LTC3200-5) Packages
3265fa
20 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTC3265
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LTC3265
LT 0316 REV A • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2015