LTC3124 - 15V, 5A 2-Phase Synchronous Step-Up DC/DC Converter with Output Disconnect

LTC3124
15V, 5A 2-Phase Synchronous
Step-Up DC/DC Converter with
Output Disconnect
FEATURES
DESCRIPTION
VIN Range: 1.8V to 5.5V, 500mV After Start-Up
n Adjustable Output Voltage: 2.5V to 15V
n1.5A Output Current for V = 5V and V
IN
OUT = 12V
n Dual-Phase Control Reduces Output Voltage Ripple
n Output Disconnects from Input When Shut Down
n Synchronous Rectification: Up to 95% Efficiency
n Inrush Current Limit
n Up to 3MHz Programmable Switching Frequency
Synchronizable to External Clock
n Selectable Burst Mode® Operation: 25µA I
Q
n Output Overvoltage Protection
n Internal Soft-Start
n<1µA I in Shutdown
Q
n16-Lead, Thermally- Enhanced 3mm × 5mm ×
0.75mm DFN and TSSOP Packages
The LTC®3124 is a dual-phase, synchronous step-up DC/
DC converter with true output disconnect and inrush
current limiting capable of providing output voltages up
to 15V. Dual-phase operation significantly reduces peak
inductor and capacitor ripple currents, minimizing inductor and capacitor size. The 2.5A per phase current limit,
along with the ability to program output voltages up to 15V
make the LTC3124 well suited for a variety of demanding
applications. Once started, operation will continue with
inputs down to 500mV.
n
APPLICATIONS
RF, Microwave Power Amplifiers
Piezo Actuators
n Small DC Motors, Thermal Printers
n12V Analog Rail from Battery, 5V, or Backup Capacitor
n
n
L, LT, LTC, LTM, Burst Mode, Linear Technology and the Linear logo are registered trademarks
and ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the
property of their respective owners.
The LTC3124 switching frequency can be programmed
from 100kHz to 3MHz to optimize applications for highest
efficiency or smallest solution footprint. The oscillator can
be synchronized to an external clock for noise sensitive
applications. Selectable Burst Mode operation reduces
quiescent current to 25µA, ensuring high efficiency across
the entire load range. An internal soft-start limits inrush
current during start-up.
Other features include a <1µA shutdown current and robust
protection under short-circuit, thermal overload, and output
overvoltage conditions. The LTC3124 is offered in both
16-lead DFN and thermally-enhanced TSSOP packages.
TYPICAL APPLICATION
5V to 12V Synchronous Boost Converter
4.7µH
SWB
BURST PWM
10µF
22µF
×2
VOUTA
SWA
LTC3124
PGNDA
VIN
SGND
PWM/SYNC
SD
VCC
RT
FB
VC
28k
1.02M
OFF ON
80
10
Burst Mode
OPERATION
70
113k
50
40
30
10
0
0.01
56pF
680pF
1
PWM
60
20
84.5k
4.7µF
VOUT
12V
1.5A
100nF
VOUTB
90
0.1
Burst Mode
OPERATION
0.01
POWER LOSS (W)
4.7µH
PGNDB
CAP
EFFICIENCY (%)
VIN
5V
Efficiency Curve
100
PWM
0.001
fSW = 1MHz
EFFICIENCY
POWER LOSS
0.0001
0.1
1
10
100
1000
LOAD CURRENT (mA)
3124 TA01b
3124 TA01a
3124f
For more information www.linear.com/LTC3124
1
LTC3124
ABSOLUTE MAXIMUM RATINGS
(Note 1)
VIN Voltage.................................................... –0.3V to 6V
VOUTA, VOUTB Voltages................................ –0.3V to 18V
SWA, SWB Voltages (Note 2)...................... –0.3V to 18V
SWA, SWB (Pulsed < 100ns) (Note 2)........ –0.3V to 19V
VC Voltage...................................................–0.3V to VCC
RT Voltage...................................................–0.3V to VCC
CAP Voltage
VOUT < 5.7V.............................–0.3V to (VOUT + 0.3V)
5.7V ≤ VOUT ≤ 11.7V...... (VOUT – 6V) to (VOUT + 0.3V)
VOUT > 11.7V..................................(VOUT – 6V) to 12V
All Other Pins................................................ –0.3V to 6V
Operating Junction Temperature Range (Notes 3, 4)
LTC3124E/LTC3124I............................ –40°C to 125°C
LTC3124H........................................... –40°C to 150°C
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec)
FE Package Only................................................ 300°C
PIN CONFIGURATION
TOP VIEW
TOP VIEW
SWB
1
16 CAP
PGNDB
2
15 VOUTB
SWA
3
14 NC
13 VOUTA
PGNDA
4
12 SGND
VIN
5
11 SD
PWM/SYNC
6
11 SD
7
10 FB
VCC
7
10 FB
8
9
VC
RT
8
9
SWB
1
16 CAP
PGNDB
2
15 VOUTB
SWA
3
14 NC
PGNDA
4
VIN
5
PWM/SYNC
6
VCC
RT
17
PGND
DHC PACKAGE
16-LEAD (5mm × 3mm) PLASTIC DFN
TJMAX = 125°C, θJA = 43°C/W (NOTE 5), θJC = 5°C/W
EXPOSED PAD (PIN 17) IS PGND AND MUST BE SOLDERED TO PCB
FOR RATED THERMAL PERFORMANCE
17
PGND
13 VOUTA
12 SGND
VC
FE PACKAGE
16-LEAD PLASTIC TSSOP
TJMAX = 150°C, θJA = 40°C/W (NOTE 5), θJC = 10°C/W
EXPOSED PAD (PIN 17) IS PGND AND MUST BE SOLDERED TO PCB
FOR RATED THERMAL PERFORMANCE
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC3124EDHC#PBF
LTC3124EDHC#TRPBF
3124
16-Lead (5mm × 3mm) Plastic DFN
–40°C to 125°C
LTC3124IDHC#PBF
LTC3124IDHC#TRPBF
3124
16-Lead (5mm × 3mm) Plastic DFN
–40°C to 125°C
LTC3124EFE#PBF
LTC3124EFE#TRPBF
3124FE
16-Lead Plastic TSSOP
–40°C to 125°C
LTC3124IFE#PBF
LTC3124IFE#TRPBF
3124FE
16-Lead Plastic TSSOP
–40°C to 125°C
LTC3124HFE#PBF
LTC3124HFE#TRPBF
3124FE
16-Lead Plastic TSSOP
–40°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping
container.Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
3124f
2
For more information www.linear.com/LTC3124
LTC3124
ELECTRICAL
CHARACTERISTICS
The l denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at TA = 25°C (Note 3). VIN = 3.6V, VOUTA = VOUTB = 12V, RT = 28k unless
otherwise noted.
PARAMETER
Minimum Start-Up Voltage
Input Voltage Range
Output Voltage Adjust Range
Feedback Voltage
Feedback Input Current
Quiescent Current, Shutdown
Quiescent Current, Active
Quiescent Current, Burst
N-Channel MOSFET Switch Leakage Current
P-Channel MOSFET Switch Leakage Current
N-Channel MOSFET Switch On-Resistance
P-Channel MOSFET Switch On-Resistance
N-Channel MOSFET Peak Current Limit
Maximum Duty Cycle
Minimum Duty Cycle
Switching Frequency
SYNC Frequency Range
PWM/SYNC Input High Voltage
PWM/SYNC Input Low Voltage
PWM/SYNC Input Current
CAP Clamp Voltage
VCC Regulation Voltage
Error Amplifier Transconductance
Error Amplifier Sink Current
Error Amplifier Source Current
Soft-Start Time
SD Input High Voltage
SD Input Low Voltage
SD Input Current
CONDITIONS
VOUT = 0V
VOUT ≥ 2.5V
MIN
l
l
l
l
FB = 1.4V
SD = 0V, VOUT = 0V, Not Including Switch Leakage
FB = 1.4V, Measured on VIN, Non-Switching
Measured on VIN, FB = 1.4V
Measured on VOUT, FB = 1.4V
SW = 15V, VOUT = 15V, Per Phase
SW = 0V, VOUT = 15V, SD = 0V, Per Phase
Per Phase
Per Phase
Per Phase
FB = 1.0V
FB = 1.4V
Per Phase
0.5
2.5
1.176
l
l
l
l
2.5
90
TYP
1.6
1.200
1
0.2
600
25
10
0.1
0.1
0.130
0.200
3.5
94
l
l
l
l
0.83
0.2
0.9 • VCC
1
l
VPWM/SYNC = 5.5V
VOUT > 6.2V, Referenced to VOUT
VIN < 2.8V, VOUT > 5V
l
–5.0
3.9
60
l
1.6
FB = 1.6V, VC = 1.15V
FB = 800mV, VC = 1.15V
0.01
–5.4
4.25
100
25
–25
10
l
SD = 5.5V
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Voltage transients on the SW pin beyond the DC limit specified in
the Absolute Maximum Ratings are non-disruptive to normal operations
when using good layout practices, as shown on the demo board or
described in the data sheet or application notes.
Note 3: The LTC3124 is tested under pulsed load conditions such that
TA ≈ TJ. The LTC3124E is guaranteed to meet performance specifications
from 0°C to 85°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LTC3124I is guaranteed to meet specifications over the –40°C to 125°C
operating junction temperature range. The LTC3124H is guaranteed to
meet specifications over the full –40°C to 150°C operating junction range.
High junction temperatures degrade operating lifetimes; operating lifetime
is derated for junction temperatures greater than 125°C.
1
MAX
1.8
5.5
15
1.224
50
1
840
40
20
40
70
4.5
0
1.17
6.0
0.1 • VCC
1
–5.8
4.6
130
0.25
2
UNITS
V
V
V
V
nA
µA
µA
µA
µA
µA
µA
Ω
Ω
A
%
%
MHz
MHz
V
V
µA
V
V
µS
µA
µA
ms
V
V
µA
Note that the maximum ambient temperature consistent with these
specifications is determined by specific operating conditions in
conjunction with board layout, the rated package thermal impedance
and other environmental factors. The junction temperature (TJ in °C) is
calculated from the ambient temperature (TA in °C) and power dissipation
(PD in Watts) according to the formula:
TJ = TA + (PD • θJA)
where θJA is the thermal impedance of the package.
Note 4: The LTC3124 includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 150°C when overtemperature shutdown is active.
Continuous operation above the specified maximum operating junction
temperature may result in device degradation or failure.
Note 5: Failure to solder the exposed backside of the package to the PC
board ground plane will result in a thermal impedance much higher than
the rated package specifications.
For more information www.linear.com/LTC3124
3124f
3
LTC3124
TYPICAL PERFORMANCE CHARACTERISTICS
Configured as front page application at TA = 25°C, unless otherwise specified.
Efficiency vs Load Current,
VOUT = 5V
Efficiency vs Load Current,
VOUT = 7.5V
100
100
Burst Mode
90 OPERATION
50
40
30
fSW = 1MHz
VIN = 4.2V
VIN = 3.3V
VIN = 0.6V
20
10
1
10
100
LOAD CURRENT (mA)
80
70
PWM
60
50
40
30
fSW = 1MHz
VIN = 5.4V
VIN = 3.8V
VIN = 2.3V
20
10
0
0.01
1000
0.1
1
10
100
LOAD CURRENT (mA)
3124 G01
PHASE A
INDUCTOR
CURRENT
500mA/DIV
OUTPUT
CURRENT
500mA/DIV
PHASE B
INDUCTOR
CURRENT
500mA/DIV
3124 G04
–0.05
–0.10
–0.15
–0.20
–0.25
–0.30
160
0.1
1
10
100
LOAD CURRENT (mA)
VOUT
5V/DIV
150mA
150mA
500µs/DIV
INDUCTOR A
CURRENT
1A/DIV
INDUCTOR B
CURRENT
1A/DIV
3124 G05
ILOAD = 100mA
3124 G06
2ms/DIV
Switching Frequency
vs Temperature
0.5
60
40
20
0
–20
–40
–50
1000
Inrush Current Control
CHANGE IN FREQUENCY FROM 25°C (%)
0
fSW = 1MHz
VIN = 5.4V
VIN = 4.2V
VIN = 2.6V
3124 G03
80
CHANGE IN RDS(ON) FROM 25°C (%)
CHANGE IN VFB FROM 25°C (%)
0
0.01
1000
RDS(ON) vs Temperature,
Both NMOS and PMOS
0.05
120
80
TEMPERATURE (°C)
30
SD
5V/DIV
RC = 169k
CC = 330pF
NO CF
Feedback vs Temperature
40
40
10
1500mA
0
50
20
VOUT
500mV/DIV
AC-COUPLED
2µs/DIV
60
Load Transient Response
VOUT
20mV/DIV
AC-COUPLED
ILOAD = 500mA
PWM
70
3124 G02
PWM Mode Operation
–0.35
–40
EFFICIENCY (%)
EFFICIENCY (%)
EFFICIENCY (%)
60
Burst Mode
OPERATION
90
80
PWM
70
0.1
100
Burst Mode
90 OPERATION
80
0
0.01
Efficiency vs Load Current,
VOUT = 12V
–10
70
110
30
TEMPERATURE (°C)
150
3124 G08
3124 G07
0
–0.5
–1.0
–1.5
–2.0
–50
–20
70
10
100
40
TEMPERATURE (°C)
130
160
3124 G09
3124f
4
For more information www.linear.com/LTC3124
LTC3124
TYPICAL PERFORMANCE CHARACTERISTICS
Configured as front page application at TA = 25°C, unless otherwise specified.
Peak Current Limit Change
vs Temperature
PWM Mode Maximum Output
Current vs VIN
OUTPUT CURRENT (A)
3.2
2.8
2.4
2.0
1.6
1.2
0.8
0.4
0
0.5
1
1.5
2
2.5 3 3.5
VIN (V)
4
4.5
5
200
VOUT = 15V
VOUT = 12V
VOUT = 7.5V
VOUT = 5V
VOUT = 2.5V
180
1
160
INPUT CURRENT (mA)
VOUT = 5V
VOUT = 7.5V
VOUT = 12V
VOUT = 15V
3.6
2
PEAK CURRENT LIMIT CHANGE FROM 25°C (%)
4.0
PWM Operation No-Load Input
Current vs VIN
0
–1
–2
140
120
100
80
60
40
–3
20
–4
–50
5.5
–10
70
110
30
TEMPERATURE (°C)
0
0.5
150
1
1.5
3124 G11
2
2.5 3 3.5
VIN (V)
4
4.5
3124 G10
Burst Mode No-Load Input
Current vs VIN
10000
VOUT = 15V
VOUT = 12V
VOUT = 7.5V
VOUT = 5V
VOUT = 2.5V
INPUT CURRENT (µA)
1000
250
200
150
100
100
50
1.5
2
2.5 3 3.5 4
VIN, FALLING (V)
VOUT = 2.5V
VOUT = 5V
VOUT = 7.5V
4.5
5
10
0.5
5.5
1
3124 G13
1.5
2
2.5 3 3.5 4
VIN, FALLING (V)
4.5
VOUT = 12V
VOUT = 15V
SD Pin Threshold
5.5
60
45
30
15
0
–15
–50
–10
70
110
30
TEMPERATURE (°C)
150
3124 G15
RT vs Frequency
VOUT
5V/DIV
100
900mV
VSD
500mV/DIV
5
75
3124 G14
RT RESISTANCE (kΩ)
OUTPUT CURRENT (mA)
350
300
Burst Mode Quiescent Current
Change vs Temperature
CHANGE IN CURRENT FROM 25°C (%)
400
1
5.5
3124 G12
Burst Mode Output Current vs VIN
0
0.5
5
400mV
1s/DIV
10
3124 G16
10
100
1000
FREQUENCY (kHz)
3000
3124 G17
For more information www.linear.com/LTC3124
3124f
5
LTC3124
TYPICAL PERFORMANCE CHARACTERISTICS
Configured as front page application at TA = 25°C, unless otherwise specified.
Frequency Accuracy
Efficiency vs Frequency
CAP Pin Voltage vs VOUT
100
2
0
EFFICIENCY (%)
1
0
–1
–2
0.5
–1
1
1.5
2
2.5 3 3.5 4
VIN, FALLING (V)
4.5
5
70
60
50
40
30
20
VOUT = 15V
VOUT = 3.6V
VOUT = 2.5V
100kHz EFFICIENCY
1MHz EFFICIENCY
3MHz EFFICIENCY
10
0
5.5
VCAP, REFERRED TO VOUT (V)
CHANGE IN FREQUENCY (%)
90
80
10
100
OUTPUT CURRENT (mA)
–2
–3
–4
–5
–6
–7
1000
0
2
4
8
6
10
VOUT (V)
12
3124 G20
3124 G19
VCC vs VIN
14
3124 G21
Burst Mode Operation to
PWM Mode
Burst Mode Operation
4.5
VOUT
100mV/DIV
AC-COUPLED
VCC (V)
4.0
VSWA
10V/DIV
3.5
VIN FALLING
VIN RISING
0
1
2
3
VIN (V)
VPWM/SYNC
2V/DIV
PHASE A
INDUCTOR
CURRENT
500mA/DIV
3.0
2.5
VOUT
50mV/DIV
AC-COUPLED
4
5
6
5µs/DIV
OUTPUT CURRENT = 50mA
3124 G23
3124 G24
50µs/DIV
OUTPUT CURRENT = 100mA
TYPE III COMPENSATION—SEE FIGURE 10 FOR
COMPONENT VALUES
3124 G22
PWM Mode to Burst Mode
Operation
Burst Mode Transient
Synchronized Operation
VOUT
100mV/DIV
AC-COUPLED
VOUT
50mV/DIV
AC-COUPLED
VSWB
10V/DIV
SYNCHRONIZED TO 1.3MHz
VSWA
10V/DIV
VPWM/SYNC
2V/DIV
OUTPUT
CURRENT
100mA/DIV
3124 G25
50µs/DIV
OUTPUT CURRENT = 100mA
TYPE III COMPENSATION—SEE FIGURE 10 FOR
COMPONENT VALUES
SYNCHRONIZATION SIGNAL SET TO 2.6MHz
100mA
10mA
VPWM/SYNC
5V/DIV
10mA
200µs/DIV
3124 G26
1µs/DIV
OUTPUT CURRENT = 1A
3124 G27
3124f
6
For more information www.linear.com/LTC3124
LTC3124
TYPICAL PERFORMANCE CHARACTERISTICS
Configured as front page application at TA = 25°C, unless otherwise specified.
SWA and SWB at 1MHz/Phase
Short-Circuit Response
SHORT-CIRCUIT
APPLIED
VOUT
5V/DIV
VSWB
5V/DIV
SHORT-CIRCUIT
REMOVED
INDUCTOR B
CURRENT
2A/DIV
VSWA
5V/DIV
INDUCTOR A
CURRENT
2A/DIV
ILOAD = 500mA
3124 G28
100µs/DIV
ILOAD = 1500mA 500ns/DIV
3124 G29
Output Voltage Ripple at 1.5A
Load with Two 10µF Ceramic
Capacitors
SW Pins while Synchronizing
to 1.2MHz
VOUT
20mV/DIV
AC-COUPLED
VSWB
5V/DIV
INDUCTOR B
CURRENT
500mA/DIV
INDUCTOR A
CURRENT
500mA/DIV
VSWA
5V/DIV
ILOAD = 1500mA 500ns/DIV
3124 G30
500ns/DIV
3124 G31
PIN FUNCTIONS
SWB, SWA (Pin 1, Pin 3): Phase B and Phase A Switch
Pins. Connect inductors from these pins to the input supply. Keep PCB trace lengths as short and wide as possible
to reduce EMI and voltage overshoot. When VOUT ≥ VIN +
2V, internal anti-ringing resistors are connected between
VIN and both SWA and SWB after their respective inductor currents have dropped to near zero, to minimize EMI.
These anti-ringing resistors are also activated in shutdown
and during the sleep periods of Burst Mode operation.
PGNDB, PGNDA, PGND (Pin 2, Pin 4, Exposed Pad
Pin 17): Power Ground. When laying out your PCB, provide
a short, direct path between PGND and the output capacitors and tie directly to the ground plane. The exposed pad
is ground and must be soldered to the PCB ground plane
for rated thermal and electrical performance.
VIN (Pin 5): Input Supply Pin. The device is powered from
VIN if VIN is initially greater than approximately 3.5V, with
VIN continuing to supply the device down to approximately
3V; otherwise the greater of VIN and VOUT supplies the
3124f
For more information www.linear.com/LTC3124
7
LTC3124
PIN FUNCTIONS
device. Place a low ESR ceramic bypass capacitor of at
least 10µF from VIN to PGND. X5R and X7R dielectrics
are preferred for their superior voltage and temperature
characteristics.
VC (Pin 9): Error Amplifier Output. A frequency compensation network is connected from this pin to SGND
to compensate the control loop. See Compensating the
Feedback Loop section for guidelines.
PWM/SYNC (Pin 6): Burst Mode Operation Select and
Oscillator Synchronization. Do not leave this pin floating.
FB (Pin 10): Feedback Input to the Error Amplifier. Connect the resistor divider tap to this pin. Connect the top
of the divider to VOUT and the bottom of the divider to
SGND. The output voltage can be adjusted from 2.5V to
15V according to the formula:
• PWM/SYNC = High. Disable Burst Mode operation and
maintain low noise, constant frequency operation.
• PWM/SYNC = Low. The converter operates in Burst
Mode, independent of load current.
• PWM/SYNC = External CLK. The internal oscillator is
synchronized to the external CLK signal. Burst Mode
operation is disabled. A clock pulse width of 100ns
minimum is required to synchronize the oscillator.
An external resistor MUST BE connected between RT
and SGND to program the oscillator slightly below the
desired synchronization frequency.
In non-synchronized applications, repeated clocking of
the PWM/SYNC pin to affect an operating mode change
is supported with these restrictions:
• Boost Mode (VOUT > VIN): IOUT < 3mA: fPWM/SYNC ≤
10Hz, IOUT ≥ 3mA: fPWM/SYNC ≤ 5kHz.
• Buck Mode (VOUT < VIN): IOUT < 5mA: fPWM/SYNC ≤
2.5Hz, IOUT ≥ 5mA: fPWM/SYNC ≤ 5kHz.
VCC (Pin 7): VCC Regulator Output. Connect a low ESR
filter capacitor of at least 4.7µF from this pin to SGND to
provide a regulated rail approximately equal to the lower of
VIN and 4.25V. When VOUT is higher than VIN, and VIN falls
below 3V, VCC will regulate to the lower of approximately
VOUT and 4.25V. A UVLO event occurs if VCC drops below
1.5V, typical. Switching is inhibited, and a soft-start is
initiated when VCC returns above 1.6V, typical.
RT (Pin 8): Frequency Adjust Pin. Connect to SGND
through an external resistor (RT) to program the oscillator
frequency according to the formula:
fOSC ≅
56
RT
fSWITCH =
 R1
VOUT = 1.2V •  1+ 
 R2 
SD (Pin 11): Logic Controlled Shutdown Input. Pulling this
pin above 1.6V enables normal, free-running operation.
Forcing this pin below 0.25V shuts the LTC3124 off, with
quiescent current below 1µA. Do not leave this pin floating.
SGND (Pin 12): Signal Ground. When laying out your PC
board, provide a short, direct path between SGND and the
ground referenced sides of all the appropriate components
connecting to pins RT, VC, and FB.
VOUTA, VOUTB (Pin 13, Pin 15): Output Voltage Senses and
the Source of the Internal Synchronous Rectifier MOSFETs.
Driver bias is derived from VOUT. Connect the output filter
capacitor from VOUT to PGND, close to the IC. A minimum
value of 10µF ceramic per phase is recommended. VOUT is
disconnected from VIN when SD is low. VOUTA and VOUTB
must be tied together.
NC (Pin 14): No Connect. Not connected internally. Connect
this pin to VOUTA/VOUTB to provide a wider VOUT copper
plane on the printed circuit board.
CAP (Pin 16): Serves as the Low Reference for the Synchronous Rectifiers Gate Drives. Connect a low ESR filter
capacitor (typically 100nF) from this pin to VOUT to provide
an elevated ground rail, approximately 5.4V below VOUT,
used to drive the synchronous rectifiers.
fOSC 28
≅
2
RT
where fOSC is in MHz and RT is in kΩ.
8
3124f
For more information www.linear.com/LTC3124
LTC3124
BLOCK DIAGRAM
VIN
VOUTB
SWB
PWM
COMP
EN
+ –
CURRENT
SENSE
+
IPEAK
COMP
LB
OVLO
STOP SWITCHING
+
–
3.5A
ADAPTIVE SLOPE COMP
VIN
1.8V TO 5.5V
+
PWM
LOGIC
AND
DRIVERS
IZERO
COMP
BURST
SLEEP
+
VIN
THERMAL SD
+
+
–
REFERENCE
1.2V
Burst
Mode
CONTROL
VREFUP
VIN
3.5A
4.25V
LDO
ADAPTIVE SLOPE COMP
OSCILLATOR
SOFTSTART
gm ERROR
AMPLIFIER
SYNC
–
+
+
VC
VCC
RC
CC
RT
PGNDB
2
8
PWM/SYNC
6
RT
13
TSD
IPEAK
COMP
CF
16
+ –
CURRENT
SENSE
CIN
9
CCAP
100nF
BULK
CONTROL
SIGNALS
VOUTA
PWM
COMP
5
VIN
+––
LA
COUT
11
16.5V
SWA
ANTIRING
VOUT
2.5V TO 15V
15
NC 14
+
3
CAP
VOUT – 5.4V RAIL
IZERO
COMP
+
–
ANTIRING
SD
SHUT
DOWN
PWM
LOGIC
AND
DRIVERS
+––
1
BULK
CONTROL
SIGNALS
VCC PGNDA
SGND
12
7
4
FB
R1
10
EXPOSED
PAD
17
R2
3124 BD
CVCC
3124f
For more information www.linear.com/LTC3124
9
LTC3124
OPERATION
The LTC3124 is a dual-phase, adjustable frequency (100kHz
to 3MHz) synchronous boost converter housed in either a
16-lead 5mm × 3mm DFN or a thermally-enhanced TSSOP
package. The LTC3124 offers the unique ability to start up
from inputs as low as 1.8V and continue to operate from
inputs as low as 0.5V, for output voltages greater than
2.5V. The device also features fixed frequency, current
mode PWM control for exceptional line and load regulation. The current mode architecture with adaptive slope
compensation provides excellent load transient response
and requires minimal output filtering. An internal 10ms
soft-start limits inrush current during start-up and simplifies the design process while minimizing the number of
external components.
With its low RDS(ON) and low gate charge internal N-channel
MOSFET switches and P-channel MOSFET synchronous
rectifiers, the LTC3124 achieves high efficiency over a
wide range of load current. High efficiency is achieved at
light loads by utilizing Burst Mode operation. Operation
can be best understood by referring to the Block Diagram.
The peak inductor current, reduced nearly by a factor of
2 when compared to a single phase step-up converter,
is given by:
1 I
∆I
ILPEAK ≅ • O + L 1
2 (1–D) 2
where IO is the average load current, D is the PWM duty
cycle, and ∆IL is the inductor ripple current. This relationship is shown graphically in Figure 1.
With 2-phase operation, one of the phases is always delivering current to the load whenever VIN is greater than
one-half VOUT (duty cycles less than 50%). As the duty
cycle decreases further, load current delivery between the
two phases begins to overlap, occurring simultaneously
for a growing portion of each phase as the duty cycle approaches zero. This significantly reduces both the output
ripple current and the peak current in each inductor, when
compared with a single-phase converter. This is illustrated
in the waveforms of Figures 2 and 3.
MULTIPHASE OPERATION
The LTC3124 uses a dual-phase architecture, rather than
the conventional single phase of other boost converters.
By having two phases equally spaced 180° apart, not only
is the output ripple frequency increased by a factor of
two, but the output capacitor ripple current is significantly
reduced. Although this architecture requires two inductors, rather than a single inductor, there are a number of
important advantages.
• Substantially lower peak inductor current allows the
use of smaller, lower cost inductors.
• Significantly reduced output ripple current minimizes
output capacitance requirement.
OUTPUT RIPPLE CURRENT (A)
3.5
SINGLE PHASE
3.0
2.5
2.0
DUAL
PHASE
1.5
1.0
0.5
0
0
0.5
1.0
1.5
TIME (µs)
3124 F01
Figure 1. Comparison of Output Ripple Current with Single Phase
and Dual Phase Boost Converter in a 1.5A Load Application
Operating at 50% Duty Cycle
• Higher frequency output ripple is easier to filter for low
noise applications.
• Input ripple current is also reduced for lower noise on
VIN.
3124f
10
For more information www.linear.com/LTC3124
LTC3124
OPERATION
LOW VOLTAGE OPERATION
SWITCH A
VOLTAGE
The LTC3124 is designed to allow start-up from input
voltages as low as 1.8V. When VOUT exceeds 2.5V, the
LTC3124 continues to regulate its output, even when VIN
falls as low as 0.5V. This feature extends operating times
by maximizing the amount of energy that can be extracted
from the input source. The limiting factors for the application become the availability of the power source to supply
sufficient power to the output at the low input voltage,
and the maximum duty cycle, which is clamped at 94%.
Note that at low input voltages, small voltage drops due
to series resistance become critical and greatly limit the
power delivery capability of the converter.
SWITCH B
VOLTAGE
INDUCTOR A
CURRENT
INDUCTOR B
CURRENT
INPUT
CURRENT
RECTIFIER A
CURRENT
RECTIFIER B
CURRENT
OUTPUT
RIPPLE
CURRENT
LOW NOISE FIXED FREQUENCY OPERATION
3124 F02
Figure 2. Simplified Voltage and Current Waveforms
for 2-Phase Operation at 50% Duty Cycle
SWITCH A
VOLTAGE
SWITCH B
VOLTAGE
INDUCTOR A
CURRENT
INDUCTOR B
CURRENT
INPUT
CURRENT
RECTIFIER A
CURRENT
RECTIFIER B
CURRENT
OUTPUT
RIPPLE
CURRENT
Soft-Start
The LTC3124 contains internal circuitry to provide softstart operation. The soft-start utilizes a linearly increasing
ramp of the error amplifier reference voltage from zero
to its nominal value of 1.2V in approximately 10ms, with
the internal control loop driving VOUT from zero to its
final programmed value. This limits the inrush current
drawn from the input source. As a result, the duration
of the soft-start is largely unaffected by the size of the
output capacitor or the output regulation voltage. The
closed-loop nature of the soft-start allows the converter
to respond to load transients that might occur during
the soft-start interval. The soft-start period is reset by a
shutdown command on SD, a UVLO event on VCC (VCC <
1.5V), an overvoltage event on VOUT (VOUT ≥ 16.5V), or
an overtemperature event (TSD is invoked when the die
temperature exceeds 170°C). Upon removal of these fault
conditions, the LTC3124 will soft-start the output voltage.
Error Amplifier
3124 F03
Figure 3. Simplified Voltage and Current Waveforms
for 2-Phase Operation at 25% Duty Cycle
The noninverting input of the transconductance error
amplifier is internally connected to the 1.2V reference and
the inverting input is connected to FB. An external resistive
voltage divider from VOUT to SGND programs the output
voltage from 2.5V to 15V via FB as shown in Figure 4.
 R1
VOUT = 1.2V  1+ 
 R2 
For more information www.linear.com/LTC3124
3124f
11
LTC3124
OPERATION
Selecting an R2 value of 113k to have approximately
10µA of bias current in the VOUT resistor divider yields
the formula:
R1 = 94 • (VOUT – 1.2V); VOUT in Volts and R1 in kΩ.
Power converter control loop compensation is set with
a simple RC network connected between VC and SGND.
VOUT
LTC3124
R1
FB
1.2V
R2
+
–
3124 F04
Figure 4. Programming the Output Voltage
Internal Current Limit
Current limit comparators shut off the N-channel MOSFET
switches once their respective peak current is reached.
Peak switch current per phase is limited to 3.5A, independent of input or output voltage, unless VOUT is below
approximately 1.5V, resulting in the current limit being
approximately half of the nominal peak values.
Lossless current sensing converts the peak current signals
of the N-channel MOSFET switches into voltages that are
summed with their respective internal slope compensation. The
summed signals are compared to the error amplifier outputs
to provide a peak current control command for the PWMs.
Zero Current Comparator
The zero current comparators monitor the inductor currents
being delivered to the output and shut off the synchronous
rectifiers when the current is approximately 50mA. This
prevents the inductor currents from reversing in polarity,
improving efficiency at light loads.
Oscillator
The internal oscillator is programmed to twice the desired
switching frequency with an external resistor from the RT
pin to SGND according to the following formula:
 56 
fOSC (MHz) ≅ 
= 2 • f (MHz)
 R T (kΩ) 
where f = switching frequency of one phase.
12
Thus RT (kΩ) ≅ 28/f (MHz). See Table 1 for various switching frequencies and their corresponding RT values.
Table 1. Switching Frequency and Their Respective RT
SWITCHING
FREQUENCY (kHz)
100
200
300
500
800
1000
1200
2000
2200
3000
RT (kΩ)
316
154
100
57.6
34.8
28
22.6
13
11.5
8.06
For desired switching frequencies not included in Table 1,
please refer to the Resistance vs Frequency curve in the
Typical Performance Characteristics section.
The oscillator can be synchronized to an external frequency
by applying a pulse train of twice the desired switching
frequency to the PWM/SYNC pin. An external resistor
must be connected between RT and SGND to program the
oscillator to a frequency approximately 25% below that of
the externally applied pulse train used for synchronization.
RT is selected in this case according to this formula:
RT(SYNC) (kΩ) ≥ 1.25 • RT(SWITCH) (kΩ)
where RT(SWITCH) is the value of RT at the desired switching
frequency, which is half of the synchronization frequency.
Shutdown
The boost converter is disabled by pulling SD below 0.25V
and enabled by pulling SD above 1.6V. Note that SD can
be driven above VIN or VOUT, as long as it is limited to less
than its absolute maximum rating.
Thermal Shutdown
If the die temperature exceeds 170°C typical, the LTC3124
will go into thermal shutdown (TSD). All switches will be
shut off until the die temperature drops by approximately
7°C, when the device re-initiates a soft-start and switching
is re-enabled.
For more information www.linear.com/LTC3124
3124f
LTC3124
OPERATION
Boost Anti-Ringing Control
Output Disconnect
When VOUT ≥ VIN + 2V, the anti-ringing circuitry connects a
resistor across each inductor to VIN to damp high frequency
ringing on the SW pins during discontinuous current mode
operation. Although the ringing of the resonant circuits
formed by the inductors and CSW(A/B) (capacitance on
the respective SW pins) is low energy, it can cause EMI
radiation if not damped.
The LTC3124’s output disconnect feature eliminates body
diode conduction of the internal P-channel MOSFET rectifiers. This feature allows for VOUT to discharge to 0V during
shutdown, and draw no current from the input source.
Inrush current will also be limited at turn-on, minimizing
surge currents seen by the input supply. Note that to obtain
the advantages of output disconnect, there must not be
an external Schottky diode connected between SWA, SWB
and VOUT. The output disconnect feature also allows VOUT
to be pulled high, without backfeeding the power source
connected to VIN.
VCC Regulator
An internal low dropout regulator generates the 4.25V
(nominal) VCC rail from VIN or VOUT, depending upon
operating conditions. VCC is supplied from VIN if VIN is
initially greater than approximately 3.5V, with VIN continuing
to supply VCC down to approximately 3V; otherwise the
greater of VIN and VOUT supplies VCC. The VCC rail powers
the internal control circuitry and power MOSFET gate drivers
of the LTC3124. The VCC regulator is disabled in shutdown
to reduce quiescent current and is enabled by forcing the
SD pin above its input high threshold. A 4.7µF or larger
capacitor must be connected between VCC and SGND.
Overvoltage Lockout
An overvoltage condition occurs when VOUT exceeds
approximately 16.5V. Switching is disabled and the internal soft-start ramp is reset. Once VOUT drops below
approximately 16V a soft-start is initiated and switching
is allowed to resume. If the boost converter output is
lightly loaded such that the time constant of the output
capacitance, COUT, and the output load resistance, ROUT
is near or greater than the soft-start time of approximately
10ms, the soft-start ramp may end before or soon after
switching resumes, defeating the inrush current limiting of
the closed-loop soft-start following an overvoltage event.
Short-Circuit Protection
The LTC3124 output disconnect feature allows output
short-circuit protection while maintaining a maximum set
current limit. To reduce power dissipation under overload
and short-circuit conditions, the peak switch current limits
are reduced to approximately 2A. Once VOUT exceeds
approximately 1.5V, the current limits are reset to their
nominal values of 3.5A per phase.
VIN > VOUT Operation
The LTC3124 step-up converter will maintain voltage
regulation even when the input voltage is above the desired
output voltage. Note that operating in this mode will exhibit
lower efficiency and a reduced output current capability.
Refer to the Typical Performance Characteristics for details.
Burst Mode OPERATION
When the PWM/SYNC pin is held low, the boost converter
operates in Burst Mode, independent of load current. This
mode of operation is typically commanded to improve
efficiency at light loads and reduce standby current at no
load. The output current (IOUT) capability in Burst Mode
operation is significantly less than in PWM mode and
varies with VIN and VOUT, as shown in Figure 5. The logic
input thresholds for this pin are determined relative to VCC
with a low being less than 10% of VCC and a high being
greater than 90% of VCC. The LTC3124 will operate in
fixed frequency PWM mode even if Burst Mode operation
is commanded during soft-start.
In Burst Mode operation, only Phase A of the LTC3124
is operational, while Phase B is disabled. The Phase A
inductor current is initially charged to approximately
700mA by turning on the N-channel MOSFET switch, at
which point the N-channel switch is turned off and the
P-channel synchronous switch is turned on, delivering
current to the output. When the inductor current discharges
to approximately zero, the cycle repeats. In Burst Mode
operation, energy is delivered to the output until the nominal
3124f
For more information www.linear.com/LTC3124
13
LTC3124
OPERATION
400
OUTPUT CURRENT (mA)
350
300
250
200
150
100
50
0
0.5
1
1.5
2
2.5 3 3.5 4
VIN, FALLING (V)
VOUT = 2.5V
VOUT = 5V
VOUT = 7.5V
4.5
5
5.5
3124 F05
VOUT = 12V
VOUT = 15V
regulation value is reached, then the LTC3124 transitions
into a very low quiescent current sleep state. In sleep, the
output switches are turned off and the LTC3124 consumes
only 25μA of quiescent current. When the output voltage droops approximately 1%, switching resumes. This
maximizes efficiency at very light loads by minimizing
switching and quiescent losses. Output voltage ripple in
Burst Mode operation is typically 1% to 2% peak-to-peak.
Additional output capacitance (22μF or greater), or the
addition of a small feedforward capacitor (10pF to 50pF)
connected between VOUT and FB can help further reduce
the output ripple.
Figure 5. Burst Mode Output Current vs VIN
APPLICATIONS INFORMATION
PCB LAYOUT CONSIDERATIONS
The LTC3124 switches currents as high as 4.5A at high
frequencies. Special attention should be paid to the PCB
layout to ensure a stable, noise-free and efficient application
circuit. Figure 6 presents the LTC3124’s 4-layer PCB demo
board layout (the schematic of which may be obtained
from the Quick Start Guide) to outline some of the primary
considerations. A few key guidelines are outlined below:
1. A 4-layer board is highly recommended for the LTC3124
to ensure stable performance over the full operating
voltage and current range. A dedicated/solid ground
plane should be placed directly under the VIN, VOUTA,
VOUTB, SWA, and SWB traces to provide a mirror plane
to minimize noise loops from high dI/dt and dV/dt
edges (see Figure 6, 2nd layer).
2. All circulating high current paths should be kept as
short as possible. Capacitor ground connections
should via down to the ground plane in the shortest
route possible. The bypass capacitors on VIN should be
placed as close to the IC as possible and should have
the shortest possible paths to ground (see Figure 6,
top layer).
3. PGNDA pin, PGNDB pin, and the exposed pad are the
power ground connections for the LTC3124. Multiple
vias should connect the back pad directly to the ground
plane. In addition, maximization of the metallization
connected to the back pad will improve the thermal
environment and improve the power handling capabilities of the IC.
4. The high current components and their connections
should all be placed over a complete ground plane to
minimize loop cross-sectional areas. This minimizes
EMI and reduces inductive drops.
5. Connections to all of the high current components
should be made as wide as possible to reduce the
series resistance. This will improve efficiency and
maximize the output current capability of the boost
converter.
6. To prevent large circulating currents from disrupting
the converters’ output voltage sensing, compensation,
and programmed switching frequency, the ground for
the resistor divider, compensation components, and
RT should be returned to the ground plane using a
via placed close to the IC and away from the power
connections.
3124f
14
For more information www.linear.com/LTC3124
LTC3124
APPLICATIONS INFORMATION
7. Keep the connections from the resistor divider to the
FB pin and from the compensation components to the
VC pin as short as possible and away from the switch
pin connections.
8. Crossover connections should be made on inner copper layers if available. If it is necessary to place these
on the ground plane, make the trace on the ground
plane as short as possible to minimize the disruption
to the ground plane (see Figure 6, 3rd layer).
Top Layer
2nd Layer
3rd Layer
Bottom Layer (Top View)
Figure 6. Example PCB Layout
For more information www.linear.com/LTC3124
3124f
15
LTC3124
APPLICATIONS INFORMATION
SCHOTTKY DIODE
Although it is not required, adding a Schottky diode from
both SW pins to VOUT can improve the converter efficiency
by up to 4%. Note that this defeats the output disconnect
and short-circuit protection features of the LTC3124.
windings) to reduce the I2R power losses, and must be
able to support the peak inductor current without saturating. Molded chokes and most chip inductors usually do
not have enough core area to support the peak inductor
currents of 3A to 4A seen on the LTC3124. To minimize
radiated noise, use a shielded inductor.
COMPONENT SELECTION
See Table 2 for suggested components and suppliers.
Inductor Selection
Table 2. Recommended Inductors
The LTC3124 can utilize small inductors due to its capability of setting a fast (up to 3MHz) switching frequency.
Larger values of inductance will allow slightly greater
output current capability by reducing the inductor ripple
current. To design a stable converter the range of inductance values is bounded by the targeted magnitude of the
internal slope compensation and is inversely proportional
to the switching frequency. The Inductor selection for the
LTC3124 has the following bounds:
10
3
µH >L > µH
f
f
The inductor peak-to-peak ripple current is given by the
following equation:
Ripple ( A ) =
VIN • ( VOUT – VIN )
f •L • VOUT
where:
L = Inductor Value in μH
f = Switching Frequency in MHz of One Phase
The inductor ripple current is a maximum at the minimum
inductor value. Substituting 3/f for the inductor value in
the above equation yields the following:
RippleMAX ( A ) =
VIN • ( VOUT – VIN )
3 • VOUT
A reasonable operating range for the inductor ripple current is typically 10% to 40% of the maximum inductor
current. High frequency ferrite core inductor materials
reduce frequency dependent power losses compared to
cheaper powdered iron types, improving efficiency. The
inductor should have low DCR (series resistance of the
Sumida CDR7D28MNNP-1R2NC
Sumida CDMC6D28NP-3R3MC
1.2
3.3
21
31
Taiyo-Yuden NR5040T3R3N
3.3
35
SIZE (mm)
ISAT
(A)
W×L×H
5.4
4.3 × 4.3 × 2.1
3.7
7.3 × 7.3 × 4.1
8.7
5.3 × 5.3 × 3.1
6.7
5.3 × 5.3 × 3.1
6.3
5.3 × 5.3 × 5.1
5.6
6.3 × 6.3 × 6.1
4.34 12.3 × 12.3 × 6.2
4.8
5.2 × 5.2 × 3
4.37 7.6 × 7.6 × 4.35
3.84 12.5 × 12.5 × 6
5.28 12.5 × 12.5 × 8
5.9
7.6 × 7.6 × 3
5
7.25 × 6.7 × 3
3.8
5×5×4
TDK LTF5022T-1R2N4R2-LC
TDK SPM6530T-3R3M
TDK VLP8040T-4R7M
1.2
3.3
4.7
25
30
25
4.3
6.8
4.4
5 × 5.2 × 2.2
7.1 × 6.5 × 3
8 × 7.7 × 4
Würth WE-LHMI 74437324010
Würth WE-PD 7447789002
Würth WE-PD 7447779002
Würth WE-PD 7447789003
Würth WE-PD 7447789004
Würth WE-HCI 7443251000
Würth WE-PD 744770122
Würth WE-PD 744770133
Würth WE-PD 7447709470
1
2.2
2.2
3.3
4.7
10
22
33
47
27
20
20
30
35
16
43
64
60
9
4.8
6
4.2
3.9
8.5
5
3.6
4.5
4.45 × 4.06 × 1.8
7.3 × 7.3 × 3.2
7.3 × 7.3 × 4.5
7.3 × 7.3 × 3.2
7.3 × 7.3 × 3.2
10 × 10 × 5
12 × 12 × 8
12 × 12 × 8
12 × 12 × 10
PART NUMBER
Coilcraft XFL4020-102ME
Coilcraft MSS7341T-332NL
Coilcraft XAL5030-332ME
Coilcraft XAL5030-472ME
Coilcraft XAL5050-562ME
Coilcraft XAL6060-223ME
Coilcraft MSS1260T-333ML
Coiltronics SD53-1R1-R
Coiltronics DR74-4R7-R
Coiltronics DR125-330-R
Coiltronics DR127-470-R
VALUE DCR
(µH) (mΩ)
1
12
3.3
18
3.3
23
4.7
36
5.6
26
22
61
33
57
1.1
20
4.7
25
33
51
47
72
Output and Input Capacitor Selection
Low ESR (equivalent series resistance) capacitors should
be used to minimize the output voltage ripple. Multilayer
ceramic capacitors are an excellent choice as they have
extremely low ESR and are available in small footprints.
X5R and X7R dielectric materials are preferred for their
ability to maintain capacitance over wide voltage and temperature ranges. Y5V types should not be used. Although
ceramic capacitors are recommended, low ESR tantalum
capacitors may be used as well.
3124f
16
For more information www.linear.com/LTC3124
LTC3124
APPLICATIONS INFORMATION
When selecting output capacitors, the magnitude of the
peak inductor current, together with the ripple voltage
specification, determine the choice of the capacitor. Both
the ESR (equivalent series resistance) of the capacitor and
the charge stored in the capacitor each cycle contribute
to the output voltage ripple.
Manufacturer,
Part Number
AVX,
1206YD226KAT2A
Value
(µF)
22
Voltage
(V)
16
SIZE L × W × H (mm)
Type, ESR (mΩ)
AVX,
1210YC226KAT2A
22
16
3.2 × 2.5 × 2.79,
X7R Ceramic
The peak-to-peak ripple due to the charge is approximately:
Murata,
GRM31CR61C226ME15L
22
16
3.2 × 1.6 × 1.8,
X5R Ceramic
Murata,
GRM32ER71C226KE18K
22
16
3.2 × 2.5 × 2.7,
X7R Ceramic
Murata,
GRM43ER61C226KE01L
22
16
4.5 × 3.2 × 2.7,
X5R Ceramic
IP = Peak inductor current
Murata,
GRM32EB31C476ME15K
47
16
3.2 × 2.5 × 2.5,
X5R Ceramic
f = Switching frequency of one phase
Panasonic,
ECJ-4YB1C226M
22
16
3.2 × 2.5 × 2.7,
X5R Ceramic
Taiyo Yuden,
EMK316BJ226ML-T
22
16
3.2 × 1.6 × 1.8,
X5R Ceramic
Taiyo Yuden,
EMK325B7226MM-TR
22
16
3.2 × 2.5 × 2.7,
X7R Ceramic
Taiyo Yuden,
EMK432BJ226KM-T
22
16
4.5 × 3.2 × 2.7,
X5R Ceramic
TDK,
C5750X7R1C476M
47
16
5.7 × 5 × 2.5,
X7R Ceramic
TDK,
C4532X5R0J107M
100
6.3
4.5 × 3.2 × 2.8,
X5R Ceramic
Nichicon,
UBC1C101MNS1GS
100
16
Sanyo,
25TQC22MV
Sanyo,
16TQC47MW
22
25
8.3 × 8.3 × 11.5,
Aluminum Polymer
7.3 x 4.3 x 1.9,
POSCAP, 45mΩ
47
16
7.3 × 4.3 × 3.1,
POSCAP, 40mΩ
Sanyo,
16TQC100M
100
16
7.3 × 4.3 × 3.1,
POSCAP, 50mΩ
Sanyo,
25SVPF47M
47
25
6.6 × 6.6 × 5.9,
OS-CON, 30mΩ
AVX, BestCap Series
BZ125A105ZLB
1F
5.5
48 × 30 × 6.1,
35mΩ, 4 Lead
39 × 17 × 3.8, 28mΩ
D = 22, H = 45
15mΩ
D = 21.5, H = 7.5
30mΩ
D = 18.5, H = 60
20mΩ
D = 18, H = 40
20 mΩ
IP • VIN
V
(V)
≈
RIPPLE(CHARGE)
COUT • VOUT • f • 2
where:
The ESR of COUT is usually the most dominant factor for
ripple in most power converters. The peak-to-peak ripple
due to the capacitor ESR is:
VRIPPLE(ESR)(V) =ILOAD • RESR •
VOUT
VIN
where RESR = capacitor equivalent series resistance.
The input filter capacitor reduces peak currents drawn
from the input source and reduces input switching noise.
A low ESR bypass capacitor with a minimum value of 10µF
should be located as close to VIN as possible.
Low ESR and high capacitance are critical to maintain low
output ripple. Capacitors can be used in parallel for even
larger capacitance values and lower effective ESR. Ceramic
capacitors are often utilized in switching converter applications due to their small size, low ESR and low leakage
currents. However, many ceramic capacitors experience
significant loss in capacitance from their rated value with
increased DC bias voltage. It is not uncommon for a small
surface mount capacitor to lose more than 50% of its rated
capacitance when operated near its rated voltage. As a
result it is sometimes necessary to use a larger capacitor value or a capacitor with a larger value and case size,
such as 1812 rather than 1206, in order to actually realize
the intended capacitance at the full operating voltage. Be
sure to consult the vendor’s curve of capacitance versus
DC bias voltage. Table 3 shows a sampling of capacitors
suited for the LTC3124 applications.
Table 3: Representative Output Capacitors
Cap-XX GS230F
1.2F
4.5
Tecate Powerburst
TPL-100/22X45
Cooper KR-5R5C155-R
100F
2.7
1.5F
5.5
Cooper
HB1860-2R5117-R
Maxwell
BCAP0050-P270
110F
2.5
50F
2.5
3.2 × 1.6 × 1.78,
X5R Ceramic
3124f
For more information www.linear.com/LTC3124
17
LTC3124
APPLICATIONS INFORMATION
For applications requiring a very low profile and very large
capacitance, the GS, GS2 and GW series from Cap-XX,
the BestCap series from AVX and PowerStor KR series
capacitors from Cooper all offer very high capacitance
and low ESR in various low profile packages.
OPERATING FREQUENCY SELECTION
There are several considerations in selecting the operating
frequency of the converter. Typically, the first consideration
is to stay clear of sensitive frequency bands, which cannot tolerate any spectral noise. For example, in products
incorporating RF communications, the 455kHz IF frequency
can be sensitive to any noise, therefore switching above
600kHz is desired. Some communications have sensitivity
to 1.1MHz and in that case a 1.5MHz switching converter
frequency may be employed. A second consideration is the
physical size of the converter. As the operating frequency
is increased, the inductor and filter capacitors typically
can be reduced in value, leading to smaller sized external
components. The smaller solution size is typically traded
for efficiency, since the switching losses due to gate charge
increase with frequency.
Another consideration is whether the application can allow
pulse-skipping. When the boost converter pulse-skips, the
minimum on-time of the converter is unable to support
the duty cycle. This results in a low frequency component
to the output ripple. In many applications where physical
size is the main criterion, running the converter in this
mode is acceptable. In applications where it is preferred
not to enter this mode, the maximum operating frequency
is given by:
f MAX _ NOSKIP < ≅
VOUT – VIN
Hz
VOUT • tON(MIN)
Thermal Considerations
For the LTC3124 to deliver its full power, it is imperative
that a good thermal path be provided to dissipate the
heat generated within the package. This can be accomplished by taking advantage of the large thermal pad on
the underside of the IC. It is recommended that multiple
vias in the printed circuit board be used to conduct heat
away from the IC and into a copper plane with as much
area as possible. If the junction temperature rises above
~170°C, the part will trip an internal thermal shutdown,
and all switching will stop until the junction temperature
drops ~7°C.
Compensating the Feedback Loop
The LTC3124 uses current mode control, with internal
adaptive slope compensation. Current mode control eliminates the second order filter due to the inductor and output
capacitor exhibited in voltage mode control, and simplifies
the power loop to a single pole filter response. Because
of this fast current control loop, the power stage of the IC
combined with the external inductor can be modeled by a
transconductance amplifier gmp and a current controlled
current source. Figure 7 shows the key equivalent small
signal elements of a boost converter.
The DC small-signal loop gain of the system shown in
Figure 7 is given by the following equation:
GBOOST = GEA •GMP •GPOWER •
R2
R1+R2
where GEA is the DC gain of the error amplifier, GMP is
the modulator gain, and GPOWER is the inductor current
to VOUT gain.
GEA = gma • RO ≈ 1000V/V
(Not Adjustable; gma ≈ 100µS, RO ≈ 10MΩ)
where tON(MIN) = minimum on-time, which is typically
around 100ns.
GMP = 2 • gmp ; gmp =
GPOWER =
∆IL
≈ 3.4S (Not Adjustable )
∆VC
∆VOUT η• VIN η• VIN •RL
=
=
∆IL
2 •IOUT
2 • VOUT
3124f
18
For more information www.linear.com/LTC3124
LTC3124
APPLICATIONS INFORMATION
– MODULATOR
+gmp
IL
ERROR
AMPLIFIER
VC
CF
RC
CC
RO
VOUT
η • VIN
•I
2 • VOUT L
RESR
+
–
RL
COUT
1.2V
REFERENCE
R1
FB
R2
CC: COMPENSATION CAPACITOR
3124 F07
RC: COMPENSATION RESISTOR
CF: HIGH FREQUENCY FILTER CAPACITOR
CPL: PHASE LEAD CAPACITOR
RPL: PHASE LEAD RESISTOR
gma: TRANSCONDUCTANCE AMPLIFIER INSIDE IC
RO: OUTPUT RESISTANCE OF gma
gmp: POWER STAGE TRANSCONDUCTANCE AMPLIFIER
COUT: OUTPUT CAPACITOR
RESR: OUTPUT CAPACITOR ESR
RL: OUTPUT RESISTANCE DEFINED AS VOUT/ILOAD(MAX)
R1, R2: FEEDBACK RESISTOR DIVIDER NETWORK
η: CONVERSION EFFICIENCY (~90% AT HIGHER CURRENTS)
Figure 7. Boost Converter Equivalent Model
Combining the two equations above yields:
GDC = GMP •GPOWER ≈
3.4 • η• VIN •RL
V/V
VOUT
Converter efficiency η will vary with IOUT and switching
frequency fSWITCH as shown in the typical performance
characteristics curves.
Output Pole: P1 =
2
Hz
2π •RL •COUT
Error Amplifier Pole:
P2 =
≈
C
1
Hz; CF < C
10
2π •RO • (CC +CF )
ESR Zero: Z2 =
RHP Zero: Z3 =
1
2π •RESR •COUT
1
Hz
2π • (R1+RPL ) •CPL
1
Hz
 R1•R2

2π • 
+RPL  •CPL
 R1+R2

Error Amplifier Filter Pole:
P5 =
≈
1
2π •RC •
CC •CF
CC +CF
Hz, CF <
CC
10
1
Hz
2π •RC •CF
The current mode zero (Z3) is a right-half plane zero
which can be an issue in feedback control design, but is
manageable with proper external component selection.
Also note that the RHP zero is a minimum at minimum
input voltage and maximum output current for a given
output voltage. As a general rule, the frequency at which
the open-loop gain of the converter is reduced to unity,
known as the crossover frequency fC , should be set to
less than one-sixth of the right-half plane zero (Z3), and
under one-eighth of the switching frequency fSWITCH. Once
fC is selected, the compensation component values can
be calculated using a Bode plot of the power stage or two
generally valid assumptions: P1 dominates the gain of the
power stage for frequencies lower than fC and fC is much
higher than P2. First calculate the power stage gain at fC,
GfC in V/V. Assuming the output pole P1 dominates GfC
for this range, it is expressed by:
1
Hz; ExtremelyClose toDC
2π •RO •CC
1
Hz
Error Amplifier Zero: Z1 =
2π •RC •CC
Phase Lead Pole: P4 =
RPL
CPL
gma
Phase Lead Zero: Z4 =
G fC ≈
GDC
f 
1+  C 
 P1
2
V/V
Hz
VIN 2 • 2RL
Hz
2π • VOUT 2 •L
High Frequency Pole: P3 >
fOSC
Hz
3
3124f
For more information www.linear.com/LTC3124
19
LTC3124
APPLICATIONS INFORMATION
Decide how much phase margin (Φm) is desired. Greater
phase margin can offer more stability while lower phase margin can yield faster transient response. Typically, Φm ≈ 60°
is optimal for minimizing transient response time while
allowing sufficient margin to account for component
variability. Φ1 is the phase boost of Z1, P2, and P5 while
Φ2 is the phase boost of Z4 and P4. Select Φ1 and Φ2
such that:
Φ1 + Φ 2 = Φm + tan−
Setting Z1, P5, Z4, and P4 such that
ƒC
ƒ
, P5 = ƒC a1, Z4 = C , P4 = ƒC a2
a1
a2
allows a1 and a2 to be determined using Φ1 and Φ2
 Φ + 90° 
 Φ + 90° 
a1 = tan2  1
, a2 = tan2  2





2
2
The compensation will force the converter gain GBOOST
to unity at ƒC by using the following expression for CC:
CC =
103 • g ma • R2 • GƒC ( a1 − 1) a2
2π • ƒC • (R1+ R2) a1
pF
(gma in µS, ƒC in kHz, GƒC in V/V)
Once CC is calculated, RC and CF are determined by:
106 • a1
RC =
kΩ (ƒC in kHz, C C in pF)
2π • ƒC • CC
CF =
 R1• R2 
R1− a2 • 
 R1+ R2 
=
kΩ and
a2 − 1
CPL =
106 ( a2 − 1) (R1+ R2)
2π • ƒC • R12 a2
pF
where R1, R2, and RPL are in kΩ and ƒC is in kHz.
where VOUT is in V and ƒC and Z3 are in kHz.
RPL
ƒC 
  and
Z3
1


V
Φ1 ≤ 74° ; Φ 2 ≤  2 • tan−1 OUT  − 90°
1.2V 

Z1=
the transfer function of the converter. The values of these
phase lead components are given by the expressions:
CC
a1 − 1
A method for improving the converter’s transient response
uses a small feedforward series network of a capacitor and
a resistor across the top resistor of the feedback divider
(from VOUT to FB). This adds a phase-lead zero and pole to
Note that selecting Φ2 = 0° forces a2 = 1, and so the
converter will have Type II compensation and therefore
no feedforward: RPL is open (infinite impedance) and CPL
= 0pF. If a2 = 0.833 • VOUT (its maximum), feedforward is
maximized; RPL = 0 and CPL is maximized for this compensation method.
Once the compensation values have been calculated, obtaining a converter bode plot is strongly recommended to
verify calculations and adjust values as required.
Using the circuit in Figure 8 as an example, Table 4 shows
the parameters used to generate the Bode plot shown in
Figure 9.
Table 4. Bode Plot Parameters
PARAMETER
VIN
VOUT
RL
COUT at No Bias
COUT at 12V Bias
RESR
LA, LB
fSWITCH
R1
R2
gma
RO
gmp
η
RC
CC
CF
RPL
CPL
VALUE
5
12
8
22 × 2
14 × 2
2.5
4.7
1
1020
113
100
10
3.4
90
84.5
680
56
Open
0
UNITS
V
V
Ω
µF
µF
COMMENT
App Specific
App Specific
App Specific
App Specific
App Specific
mΩ
µH
MHz
kΩ
kΩ
µS
MΩ
S
%
App Specific
App Specific
Adjustable
Adjustable
Adjustable
Fixed
Fixed
Fixed
App Specific
kΩ
pF
pF
kΩ
pF
Adjustable
Adjustable
Adjustable
Optional
Optional
3124f
20
For more information www.linear.com/LTC3124
LTC3124
APPLICATIONS INFORMATION
Switching Waveforms with 1.5A Load
SWB
LA
4.7µH
PGNDB
CAP
C1
100nF
VOUTB
VIN
BURST PWM
CIN
10µF
CVCC
4.7µF
VOUT
20mV/DIV
AC-COUPLED
SD
VCC
RT
FB
VC
CC
680pF
200ns/DIV
R2
113k
RC
84.5k
VOUT
500mV/DIV
AC-COUPLED
3124 F08
OUTPUT
CURRENT
500mA/DIV
Figure 8. 1MHz, 5V to 12V, 1.5A Boost Converter
1500mA
700mA
700mA
100µs/DIV
45
90
30
45
PHASE
0
GAIN
0
–45
–15
–90
–30
–135
1k
10k
FREQUENCY (Hz)
100k
3124 F08c
PHASE (DEG)
15
–45
100
3124 F08b
Transient Response with 700mA to 1.5A Load Step
CF
56pF
C1: 100nF, 16V, X5R, 0805
CIN: 10µF, 10V, X5R, 1206
COUT: 22µF ×2, 16V, X5R, 1210
CVCC: 4.7µF, 10V, X5R, 1206
LA, LB: COILCRAFT XAL5030-472ME
INDUCTOR A
CURRENT
1A/DIV
VSWA
10V/DIV
R1
1.02M
OFF ON
INDUCTOR B
CURRENT
1A/DIV
VSWB
10V/DIV
SGND
PWM/SYNC
RT
28k
VOUT
12V
1.5A
COUT
22µF
×2
SWA
VOUTA
LTC3124
PGNDA
GAIN (dB)
VIN
5V
LB
4.7µH
–180
3124 F09
Figure 9. Bode Plot for Example Converter
3124f
For more information www.linear.com/LTC3124
21
LTC3124
APPLICATIONS INFORMATION
From Figure 9, the phase is ~60° when the gain reaches
0dB, so the phase margin of the converter is ~60°. The
crossover frequency is ~10kHz, which is more than six
times lower than the 94kHz frequency of the RHP zero to
achieve adequate phase margin.
The circuit in Figure 10 shows the same application as
that in Figure 8 with Type III compensation. This is accomplished by adding CPL and RPL and adjusting CC, CF,
and RC accordingly. Table 5 shows the parameters used
to generate the bode plot shown in Figure 11.
From Figure 11, the phase margin is still optimized at ~60°
and the crossover frequency remains ~10kHz. Adding CPL
and RPL provides some feedforward signal in Burst Mode
operation, leading to lower output voltage ripple.
VIN
5V
LB
4.7µH
SWB
LA
4.7µH
CAP
PGNDB
C1
100nF
VOUTB
VOUTA
SWA
LTC3124
PGNDA
VIN
BURST PWM
CIN
10µF
CVCC
4.7µF
RPL
787k
CPL
12pF
SGND
PWM/SYNC
SD
VCC
RT
FB
VC
RT
28k
CC
470pF
VOUT
12V
1.5A
COUT
22µF
×2
OFF ON
R1
1.02M
R2
113k
RC
71.5k
CF
120pF
C1: 100nF, 16V, X5R, 0805
CIN: 10µF, 10V, X5R, 1206
COUT: 22µF ×2, 16V, X5R, 1210
CVCC: 4.7µF, 10V, X5R, 1206
LA, LB: COILCRAFT XAL5030-472ME
3124 F10
Figure 10. Boost Converter with Phase Lead
Table 5. Bode Plot Parameters
η
RC
CC
CF
RPL
CPL
22 × 2
14 × 2
2.5
4.7
1
113
1020
100
10
3.4
90
71.5
470
120
787
12
UNITS
V
V
Ω
µF
µF
COMMENT
App Specific
App Specific
App Specific
App Specific
App Specific
mΩ
µH
MHz
kΩ
kΩ
µS
MΩ
S
%
App Specific
App Specific
Adjustable
Adjustable
Adjustable
Fixed
Fixed
Fixed
App Specific
kΩ
pF
pF
kΩ
pF
Adjustable
Adjustable
Adjustable
Adjustable
Adjustable
90
45
45
30
PHASE
15
GAIN (dB)
RESR
LA, LB
fSWITCH
R1
R2
gma
RO
gmp
VALUE
5
12
8
0
GAIN
0
–45
–15
–90
–30
–135
–45
100
1k
10k
FREQUENCY (Hz)
100k
PHASE (DEG)
PARAMETER
VIN
VOUT
RL
COUT at No Bias
COUT at 12V Bias
–180
3124 F11
Figure 11. Bode Plot Showing Phase Lead
3124f
22
For more information www.linear.com/LTC3124
LTC3124
TYPICAL APPLICATIONS
Single Li Cell to 6V, 9W, 2.2MHz Synchronous Boost Converter
for RF Transmitter
VOUT
500mV/DIV
AC-COUPLED
LB
2.2µH
VIN
2.7V TO 4.2V
SWB
LA
2.2µH
CAP
PGNDB
CIN
10µF
CVCC
4.7µF
C1
100nF
VOUTB
VOUT
6V
1.5A
COUT
47µF
×2
VOUTA
SWA
LTC3124
PGNDA
VIN
Load Step
1.5A
OUTPUT
CURRENT
500mA/DIV
SD
VCC
RT
FB
VC
RT
11.5k
150mA
VIN = 3.6V
SGND
PWM/SYNC
150mA
3124 TA02b
R1
1.13M
OFF ON
RC
60.4k
CC
1.2nF
100µs/DIV
Bode Plot
R2
280k
CF
68pF
50
120
40
90
30
GAIN (dB)
60
PHASE
20
3124 TA02a
10
30
0
GAIN
0
–30
–10
–60
PHASE (DEG)
C1: 100nF, 16V, X5R, 0805
CIN: 10µF, 10V, X5R, 1206
COUT: 47µF × 2, 16V, X5R, 1210
CVCC: 4.7µF, 10V, X5R, 1206
LA, LB: WÜRTH WE-PD 7447779002
–20
–90
–30
–120
–40
–150
–50
100
1k
10k
FREQUENCY (Hz)
–180
100k
3124 TA02c
2-Port USB-Powered 1MHz Synchronous Boost Converter to 5V, 500mA
LB
3.3µH
VIN
4.3V TO 5.5V
SWB
LA
3.3µH
PGNDB
CAP
VOUTB
VOUTA
SWA
LTC3124
PGNDA
VIN
C2
10µF
CIN
10µF
CVCC
4.7µF
SD
VCC
RT
FB
VC
C1: 100nF, 16V, X5R, 0805
C2: KEMET T491C106K025AS
CIN: 10µF, 10V, X5R, 1206
COUT: 100µF × 2, 6.3V, X5R, 1812
CVCC: 4.7µF, 10V, X5R, 1206
LA, LB: COILCRAFT XAL5030-332ME
VOUT
5V
500mA
COUT
100µF
×2
R1
1.47M
OFF ON
RC
35.7k
CC
2.7nF
2-Port USB 2.0 Hot Plugged
VIN
2V/DIV
SGND
PWM/SYNC
RT
28k
C1
100nF
R2
464k
VOUT
2V/DIV
INPUT
CURRENT
500mA/DIV
CF
270pF
RLOAD = 10Ω
2ms/DIV
VIN = USB 2.0
2-PORT HOT PLUGGED
3124 TA03b
3124 TA03a
3124f
For more information www.linear.com/LTC3124
23
LTC3124
TYPICAL APPLICATIONS
3.3V to 12V, 300kHz Synchronous Boost Converter
with Output Disconnect, 1A
Efficiency
LB
22µH
SWB
LA
22µH
CAP
PGNDB
VOUTB
BURST PWM
CVCC
4.7µF
SGND
PWM/SYNC
SD
VCC
RT
FB
VC
R1
1.02M
OFF ON
RC
76.8k
CC
3.9nF
RT
100k
100
VOUT
12V
1A
COUT
47µF
×3
VOUTA
SWA
LTC3124
PGNDA
VIN
CIN
10µF
C1
100nF
CF
270pF
C1: 100nF, 16V, X5R, 0805
CIN: 10µF, 10V, X5R, 1206
COUT: 47µF × 3, 16V, X5R, 1210
CVCC: 4.7µF, 10V, X5R, 1206
LA, LB: WÜRTH WE-PDF 7447998221
90
Burst Mode
OPERATION
80
EFFICIENCY (%)
VIN
3.3V
R2
113k
70
60
PWM
50
40
30
VCC DERIVED
FROM VIN
VCC DERIVED
FROM VOUT
20
10
0
0.01
0.1
3124 TA04a
1
10
100
LOAD CURRENT (mA)
1000
3124 TA04b
Single Li Cell to 5V, 1.8A Synchronized 1.2MHz Switching Boost
Converter for RFPA Power Supply
Efficiency
LB
3.3µH
SWB
LA
3.3µH
PGNDB
CVCC
4.7µF
VOUTB
VOUTA
SWA
LTC3124
PGNDA
2.4MHz SYNC PULSE
CIN
10µF
CAP
VIN
COUT
22µF
×2
SD
VCC
RT
FB
VC
CF
150pF
C1: 100nF, 16V, X7R, 0805
CIN: 10µF, 10V, X7R, 1206
COUT: 22µF × 2, 16V, X7R, 1210
CVCC: 4.7µF, 10V, X7R, 1206
LA, LB: COILCRAFT MSS7341T-332NL
R1
1.47M
OFF ON
RC
31.6k
CC
1.5nF
100
VOUT
5V
1.8A
SGND
PWM/SYNC
RT
28.7k
C1
100nF
R2
464k
90
80
EFFICIENCY (%)
VIN
2.7V TO 4.2V
Burst Mode
OPERATION
70
60
PWM
50
40
30
20
4.2VIN
3.3VIN
2.7VIN
10
0
0.01
3124 TA05a
0.1
1
10
100
LOAD CURRENT (mA)
1000
3124 TA05b
3124f
24
For more information www.linear.com/LTC3124
LTC3124
TYPICAL APPLICATIONS
1.8V to 5.5V Input to 15V Output, 500kHz Synchronous Boost
Converter with Output Disconnect, 300mA
Efficiency
LB
10µH
SWB
LA
10µH
PGNDB
CAP
C1
100nF
VOUTB
COUT
22µF
×2
VOUTA
SWA
LTC3124
PGNDA
VIN
CIN
10µF
CVCC
4.7µF
100
VOUT
15V
300mA
SGND
PWM/SYNC
SD
VCC
RT
FB
VC
RT
57.6k
R1
1.3M
OFF ON
RC
49.9k
CC
3.3nF
CF
100pF
R2
113k
C1: 100nF, 16V, X7R, 0805
CIN: 10µF, 10V, X7R, 1206
COUT: 22µF × 2, 16V, X7R, 1210
CVCC: 4.7µF, 10V, X7R, 1206
LA, LB: WÜRTH WE-HCI 7443251000
OUTPUT CURRENT = 300mA
95
EFFICIENCY (%)
VIN
1.8V TO 5.5V
90
85
80
75
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VIN (V)
3124 TA06a
3124 TA06b
Single Li Cell to 12V, 1MHz Synchronous Boost Converter
with Output Disconnect, 800mA
LB
5.6µH
VIN
2.7V TO 4.2V
SWB
LA
5.6µH
PGNDB
CAP
VOUTB
VOUTA
SWA
LTC3124
PGNDA
VIN
CIN
10µF
CVCC
4.7µF
C1
100nF
VOUT
12V
800mA
COUT
22µF
×2
SGND
PWM/SYNC
SD
VCC
RT
FB
VC
RT
28k
R1
1.02M
OFF ON
RC
88.7k
CC
680pF
C1: 100nF, 16V, X7R, 0805
CIN: 10µF, 10V, X7R, 1206
COUT: 22µF × 2, 16V, X7R, 1210
CVCC: 4.7µF, 10V, X7R, 1206
LA, LB: COILCRAFT XAL5050-562ME
CF
47pF
R2
113k
3124 TA08
3124f
For more information www.linear.com/LTC3124
25
LTC3124
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
DHC Package
16-Lead Plastic DFN (5mm × 3mm)
(Reference LTC DWG # 05-08-1706 Rev Ø)
0.65 ±0.05
3.50 ±0.05
1.65 ±0.05
2.20 ±0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 ± 0.05
0.50 BSC
4.40 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
5.00 ±0.10
(2 SIDES)
R = 0.20
TYP
3.00 ±0.10
(2 SIDES)
9
R = 0.115
TYP
0.40 ±0.10
16
1.65 ±0.10
(2 SIDES)
PIN 1
TOP MARK
(SEE NOTE 6)
PIN 1
NOTCH
0.200 REF
0.75 ±0.05
0.00 – 0.05
8
1
0.25 ±0.05
0.50 BSC
(DHC16) DFN 1103
4.40 ±0.10
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WJED-1) IN JEDEC
PACKAGE OUTLINE MO-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
3124f
26
For more information www.linear.com/LTC3124
LTC3124
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
FE Package
16-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1663 Rev J)
Exposed Pad Variation BC
4.90 – 5.10*
(.193 – .201)
3.58
(.141)
16 1514 13 12 11
6.60 ±0.10
4.50 ±0.10
0.48
(.019)
REF
3.58
(.141)
2.94
(.116)
10 9
DETAIL B
6.40
2.94
(.252)
(.116)
BSC
SEE NOTE 4
0.45 ±0.05
1.05 ±0.10
0.51
(.020)
REF
DETAIL B IS THE PART OF
THE LEAD FRAME FEATURE
FOR REFERENCE ONLY
NO MEASUREMENT PURPOSE
0.65 BSC
1 2 3 4 5 6 7 8
RECOMMENDED SOLDER PAD LAYOUT
4.30 – 4.50*
(.169 – .177)
0.09 – 0.20
(.0035 – .0079)
0.50 – 0.75
(.020 – .030)
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
3. DRAWING NOT TO SCALE
0.25
REF
1.10
(.0433)
MAX
0° – 8°
0.65
(.0256)
BSC
0.195 – 0.30
(.0077 – .0118)
TYP
0.05 – 0.15
(.002 – .006)
FE16 (BC) TSSOP REV J 1012
4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
3124f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
For more
information
www.linear.com/LTC3124
27
LTC3124
TYPICAL APPLICATION
PWM Rundown Curve
Dual Supercapacitor Backup Power Supply, 0.5V to 5.4V
LB
3.3µH
VIN
0.5V TO 5.4V
SWB
LA
3.3µH
PGNDB
C1
100nF
VOUTB
VIN
+
VOUT
5V
COUT
100µF
×2
OUTPUT
CURRENT
100mA/DIV
R3
1M
SD
VCC
FB
RT
VC
RT
28k
R1
1.47M
OFF ON
RC
59k
CC
1.5nF
C1: 100nF, 16V, X5R, 0805
CIN: 10µF, 10V, X5R, 1206
COUT: 100µF × 2, 6.3V, X5R, 1812
CVCC: 4.7µF, 10V, X5R, 1206
LA, LB: COILCRAFT XAL5030-332ME
SC1, SC2: TECATE POWERBURST TPL-100/22X45
SD
2V/DIV
SUPPLY REMOVED
FROM SUPERCAP
VOUT
5V/DIV
VIN
SGND
PWM/SYNC
+
CVCC
4.7µF
CAP
VOUTA
SWA
LTC3124
PGNDA
CIN
10µF
SC1
100F
SC2
100F
VIN
2V/DIV
CF
47pF
R2
464k
3124 TA07b
Burst Mode Rundown Curve
VIN
2V/DIV
SD
2V/DIV
3124 TA07a
200s/DIV
SUPPLY REMOVED
FROM SUPERCAP
VOUT
5V/DIV
OUTPUT
CURRENT
20mA/DIV
500s/DIV
3124 TA07c
RELATED PARTS
PART NUMBER
LTC3459
LTC3528
LTC3539
LTC3421
LTC3428
LTC3425
LTC3122
LTC3112
LTC3114-1
LTC3115-1
DESCRIPTION
70mA ISW, 10V Micropower Synchronous Boost Converter
with Output Disconnect, Burst Mode Operation
1A ISW, 1MHz, Synchronous Step-Up DC/DC Converter with
Output Disconnect, Burst Mode Operation
2A ISW, 1MHz/2MHz, Synchronous Step-Up DC/DC Converters
with Output Disconnect, Burst Mode Operation
3A ISW, 3MHz, Synchronous Step-Up DC/DC Converter with
Output Disconnect
4A ISW, 2MHz (1MHz Switching), Dual Phase Step-Up
DC/DC Converter
5A ISW, 8MHz, Low Ripple, 4-Phase Synchronous Step-Up
DC/DC Converter with Output Disconnect
2.5A ISW, 3MHz, Synchronous Step-Up DC/DC Converter with
Output Disconnect, Burst Mode Operation
COMMENTS
VIN: 1.5V to 5.5V, VOUT(MAX) = 10V, IQ = 10μA, ISD < 1μA,
ThinSOT Package
94% Efficiency VIN: 700mV to 5.25V, VOUT(MAX) = 5.25V, IQ = 12µA,
ISD < 1µA, 2mm × 3mm DFN Package
94% Efficiency VIN: 700mV to 5.25V, VOUT(MAX) = 5.25V, IQ = 10uA,
ISD < 1µA, 2mm × 3mm DFN Package
95% Efficiency VIN: 0.5V to 4.5V, VOUT(MAX) = 5.25V, IQ = 12μA,
ISD < 1μA, QFN24 Package
92% Efficiency VIN: 1.6V to 4.5V, VOUT(MAX) = 5.25V, ISD < 1µA,
3mm × 3mm DFN Package
95% Efficiency VIN: 0.5V to 4.5V, VOUT(MAX) = 5.25V, IQ = 12μA,
ISD < 1μA, QFN32
95% Efficiency VIN: 1.8V to 5.5V [500mV After Start-Up],
VOUT(MAX) = 15V, IQ = 25μA, ISD < 1μA, 3mm × 4mm DFN
and MSOP Packages
15V, 2.5A, 750kHz, Synchronous Buck-Boost DC/DC Converter 95% Efficiency VIN: 2.7V to 15V, VOUT(MAX) = 14V, IQ = 50μA,
ISD < 1μA, 4mm × 5mm DFN and TSSOP Packages
with Output Disconnect, Burst Mode Operation
40V, 1A, 2MHz, Synchronous Buck-Boost DC/DC Converter
95% Efficiency VIN: 2.2V to 40V, VOUT(MAX) = 40V, IQ = 30μA,
ISD = 3μA, 3mm × 5mm DFN and TSSOP Packages
with Output Disconnect, Output Current Limit, Burst Mode
Operation
40V, 2A, 2MHz, Synchronous Buck-Boost DC/DC Converter
95% Efficiency VIN: 2.7V to 40V, VOUT(MAX) = 40V, IQ = 30μA,
ISD = 3μA, 4mm × 5mm DFN and TSSOP Packages
with Output Disconnect, Burst Mode Operation
3124f
28
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTC3124
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LTC3124
LT 0614 • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2014