REVISIONS LTR DESCRIPTION F Add Arcotronics. Change parameters for dash numbers 57 through 63. G Add Arcotronics additional capacitors. H Add M.E. Technologies capacitors. J Add additional M.E. Technologies capacitors. K L M N P R Add additional Arcotronics capacitors. Add additional M.E. Technologies capacitors. Delete M.E. Technologies capacitors. Add Arcotronics additional capacitors. Add AVX capacitors. Remove Arcotronics and add Evans capacitors. Corrected the lead diameter tolerance in figure 1 and editorial changes throughout. Add new PINs for vendor A. T U DATE APPROVED 21 January 2004 K. Cottongim 9 July 2004 K. Cottongim 22 April 2005 K. Cottongim 21 October 2005 Andrew Ernst 6 April 2006 17 July 2006 5 March 2007 15 November 2007 4 June 2008 15 January 2010 Michael A. Radecki Michael A. Radecki Michael A. Radecki Michael A. Radecki Michael A. Radecki Michael A. Radecki 9 September 2013 Michael A. Radecki 31 October 2014 Michael A. Radecki PIN'S 93026-01 THROUGH 93026-28 ARE INACTIVE FOR NEW DESIGN AFTER 1 OCTOBER 1993, FOR NEW DESIGN USE PIN'S 93026-29 THROUGH 93026-65. These capacitors were designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES PMIC N/A Original date of drawing 14 January 1993 REV U U U U U U U U U U U U PAGES 1 2 3 4 5 6 7 8 9 10 11 12 PREPARED BY Ken Bernier CHECKED BY Ken Bernier APPROVED BY David E. Moore SIZE A REV AMSC N/A CODE IDENT. NO. 14933 U DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 TITLE CAPACITOR, FIXED, ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM (POLARIZED, SINTERED SLUG) DWG NO. 93026 PAGE 1 OF 12 5910-2015-E01 1. SCOPE 1.1 Scope. This drawing describes the complete requirements for tantalum electrolytic (nonsolid) electrolyte, fixed capacitors, in tantalum cases, insulated and uninsulated. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 93026 -01 K S Drawing Number Dash number (see table I) Capacitance tolerance K=±10 percent M=±20 percent S=sleeved units U=unsleeved units 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4 and 5 of this drawing. This section does not include documents cited in other sections of this drawing or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3, 4 and 5 of this drawing, whether or not they are listed here. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-39006 - Capacitors, Fixed, Electrolytic (Non-Solid Electrolyte), Tantalum Established Reliability, General Specification for DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 MIL-STD-790 - MIL-STD-1276 MIL-STD-1285 - Electronic and Electrical Component Parts, Test methods for. Standard Practice for Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications. Leads for Electronic Component Parts. Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http://quicksearch.dla.mil/.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related associated specifications, specification sheets, or MS sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE CODE IDENT NO. DWG NO. A 14933 93026 REV U PAGE 2 Dimensions mm (inches) Case size T1 T2 T3 T4 L2 Basic case L +0.79 (.031) -0.41 (.016) 11.51 (.453) 16.28 (.641) 19.46 (.766) 26.97 (1.062) 25.60 (1.008) Insulated case D ±0.41 (.016) E ±6.35 (.250) D Max 4.78 (.188) 7.14 (.281) 9.52 (.375) 9.52 (.375) 7.14 (.281) 5.56 (.219) 7.92 (.312) 10.31 (.406) 10.31 (.406) 7.92 (.312) 38.10 (1.500) 57.15 (2.250) 57.15 (2.250) 57.15 (2.250) 57.15 (2.250) NOTES: 1. Dimensions are in millimeters. 2. Inches are in parentheses. 3. The weld shall not be enclosed in the end seal. FIGURE 1. Dimensions and configuration. DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE CODE IDENT NO. DWG NO. A 14933 93026 REV U PAGE 3 FIGURE 2. Voltage derating with temperature. 3. REQUIREMENTS 3.1 Design and physical dimensions. The design and physical dimensions shall be as specified herein (see figure 1). 3.1.1 Terminals. All terminals shall be permanently secured internally and externally, as applicable. All external joints shall be welded. Terminals shall be tin-lead coated with a minimum lead content of 3 percent and conform to type N32, N51, or N52 as specified in MIL-STD-1276. The length and diameter of the terminals shall be as specified in figure 1. 3.1.2 Pure tin. The use of pure tin as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.1.3 Case. The case shall be made of tantalum. 3.1.4 Sleeving (when applicable). Shrink fitted insulation shall be used for the sleeving, and it shall lap over the ends of the capacitor body. 3.1.5 Capacitor element. The capacitor element shall consist of an anode of a sintered tantalum slug. 3.1.6 Rated temperature. The capacitor is rated for its given voltage from -55°C to +85°C. It is derated to two thirds of its given voltage at +125°C. See figure 2 for voltage derating with temperature. 3.2 Electrical characteristics. The electrical characteristics shall be as shown in table I and table II. 3.3 Seal. When the capacitors are tested as specified in MIL-PRF-39006, there shall be no evidence of leakage. DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE CODE IDENT NO. DWG NO. A 14933 93026 REV U PAGE 4 3.4 Shock. The capacitors shall meet the requirements of MIL-PRF-39006 when tested in accordance with test condition I, method 213 of MIL-STD-202. 3.5 Vibration, high frequency. The capacitors shall meet the requirements of MIL-PRF-39006 when tested in accordance with test condition D, method 204 of MIL-STD-202. 3.6 Thermal shock. Thermal shock shall be in accordance with MIL-PRF-39006 when tested for 30 cycles. 3.7 Salt atmosphere (corrosion). Salt atmosphere shall be in accordance with MIL-PRF-39006. 3.8 Solderability. Solderability shall be in accordance with MIL-PRF-39006. 3.9 Terminal strength. Terminal strength shall be in accordance with MIL-PRF-39006. 3.10 Surge voltage. Surge voltage shall be in accordance with MIL-PRF-39006 and table II of this drawing. 3.11 Moisture resistance. Moisture resistance shall be in accordance with MIL-PRF-39006. 3.12 Dielectric withstanding voltage. Dielectric withstanding voltage shall be in accordance with MIL-PRF-39006. 3.13 Insulation resistance. Insulation resistance shall be in accordance with MIL-PRF-39006. 3.14 Low temperature storage. Low temperature storage shall be in accordance with MIL-PRF-39006. 3.15 Stability at high and low temperature. Stability at high and low temperature shall be in accordance with MIL-PRF-39006. 3.16 Reverse voltage. There shall be no continuous reverse voltage. Transient reverse voltage surges are acceptable under the following conditions: a. The peak reverse voltage is equal to or less than 1.5 volts and the product of the peak current times the duration of the reverse transient is 0.05 ampere-second or less. b. The repetition rate of the reverse voltage surges is less than 10 Hz. 3.17 Life testing. The capacitors shall be capable of withstanding a 10,000 hour life test at +85°C at rated voltage, or a 2,000 hour life test at +125°C test at derated voltage. After the test, the capacitors shall meet the following requirements: a. DC leakage at (+85°C and +125°C) shall not exceed 125 percent of the specified value (see table I). b. DC leakage at (+25°C) shall not exceed the specified value (see table I). c. Capacitance shall be within +10, -20 percent of initial value. d. ESR shall not exceed 200 percent of the specified value (see table I). e. Dielectric withstanding voltage in accordance with MIL-PRF-39006. f. Insulation resistance in accordance with MIL-PRF-39006. g. Visual examination shall show no damage, obliteration of marking, or leakage of electrolyte. DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE CODE IDENT NO. DWG NO. A 14933 93026 REV U PAGE 5 3.18 AC ripple life. AC ripple life shall be in accordance with MIL-PRF-39006 and shall not exceed the specified value (see table I and table III). 3.18.1 AC ripple current multipliers vs. frequency, temperature, and applied voltage. See table III. 3.19 Impedance. Impedance shall be in accordance with MIL-PRF-39006 and shall not exceed the specified value (see table I). 3.20 Barometric pressure (reduced). Barometric pressure shall be in accordance with MIL-PRF-39006. 3.21 Resistance to solvents. Resistance to solvents shall be in accordance with MIL-PRF-39006. 3.22 Resistance to soldering heat. Resistance to soldering heat shall be in accordance with MIL-PRF-39006. 3.23 Marking. Marking shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2 with the manufacturers name or CAGE code, date code, lot symbol, capacitance (in uF), and rated voltage. 3.24 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.25 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MILPRF-39006 Qualified Products List (QPL) for at least one style or perform all testing specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VA. 3.26 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.27 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Product assurance program. The product assurance program specified in MIL-PRF-39006 and maintained in accordance with MIL-STD-790 is not applicable to this document. 4.2 Qualification inspection. Qualification inspection is not applicable to this document. 4.3 Failure rate qualification. The failure rate qualification specified in MIL-PRF-39006 is not applicable to this document. 4.4 Quality conformance inspections. 4.4.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A inspection of MIL-PRF-39006. 4.4.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2c). Note, per 3.17, 2000 hour life testing may be substituted for 10,000 hour +85° life testing. 4.5 Visual and mechanical examination. Capacitors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with applicable requirements of MIL-PRF-39006. 4.6 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use their own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth herein where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE CODE IDENT NO. DWG NO. A 14933 93026 REV U PAGE 6 TABLE I. Electrical characteristics. DSCC drawing 930261/ Cap. (µF) at +25°C and 120 Hz Case size Max ESR Ohms 120 Hz 01-02-03-04-- 120 560 1200 1800 T1 T2 T3 T4 1.3 0.83 0.65 0.5 05-06-07-08-- 100 470 1000 1500 T1 T2 T3 T4 1.3 0.85 0.7 0.6 09-10-11-12-- 68 220 470 680 T1 T2 T3 T4 1.5 0.9 0.75 0.7 13-14-15-16-- 47 150 390 560 T1 T2 T3 T4 2.0 1.1 0.9 0.8 17-18-19-20-- 33 110 330 470 T1 T2 T3 T4 2.5 1.3 1.0 0.9 21-22-23-24-- 15 68 150 220 T1 T2 T3 T4 3.5 2.1 1.6 1.2 25-26-27-28-- 10 47 100 150 T1 T2 T3 T4 5.5 2.3 1.8 1.6 Max DCL uA +85°C and +25°C +125°C 25 V dc at +85°C 1 5 2 10 3 20 4 25 30 V dc at +85°C 1 5 2 10 3 20 5 30 50 V dc at +85°C 1 5 2 10 3 25 5 40 60V dc at +85°C 1 5 2 10 3 25 5 40 75V dc at +85°C 1 5 2 10 3 30 5 50 100 V dc at +85°C 1 5 2 10 3 25 5 50 125 V dc at +85°C 1 5 2 10 3 25 5 50 Max impedance ohms at -55°C 120 Hz 20 8 7 3 25 13 9 5 30 15 11 6 40 18 13 8 50 30 18 10 110 35 23 18 160 50 50 18 Maximum capacitance change in percent -55°C +85°C 15 V dc at +125°C -30 +8 -49 +10 -54 +12 -63 +12 20 V dc at +125°C -25 +8 -45 +10 -50 +10 -60 +10 30 V dc at +125°C -18 +8 -38 +8 -50 +8 -60 +10 40 V dc at +125°C -16 +8 -35 +8 -50 +8 -60 +8 50 V dc at +125°C -12 +5 -30 +6 -50 +6 -60 +6 65 V dc at +125°C -9 +3 -22 +4 -38 +6 -50 +6 85 V dc at +125°C -7 +3 -20 +5 -25 +5 -35 +6 +125°C AC ripple +85°C 40 KHz mA rms 3/ +12 +15 +18 +20 1250 2100 2600 3100 +12 +18 +18 +20 1200 1800 2500 3000 +15 +15 +15 +20 1050 1800 2100 2750 +12 +15 +15 +15 1050 1650 2100 2750 +9 +10 +10 +10 1050 1650 2100 2750 +3 +4 +6 +6 1050 1650 2100 2750 +3 +5 +5 +6 1050 1650 2100 2750 See footnotes at end of table. DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE CODE IDENT NO. DWG NO. A 14933 93026 REV U PAGE 7 TABLE I. Electrical characteristics - Continued. DSCC drawing 930262/ Cap. (µF) at +25°C and 120 Hz Case size 29-30-57-31-32-64-- 120 560 1100 1200 1800 2200 T1 T2 L2 T3 T4 T4 33-34-58-35-36-- 100 470 950 1000 1500 T1 T2 L2 T3 T4 37-38-59-39-40-- 68 220 450 470 680 T1 T2 L2 T3 T4 41-42-60-43-44-65-- 47 150 370 390 560 1000 T1 T2 L2 T3 T4 T4 45-46-61-47-48-- 33 110 250 330 470 T1 T2 L2 T3 T4 49-50-62-51-52-- 15 68 120 150 220 T1 T2 L2 T3 T4 53-54-63-55-56-- 10 47 90 100 150 T1 T2 L2 T3 T4 Max DCL uA +85°C and +25°C +125°C 25 V dc at +85°C 1.3 1 5 0.83 2 10 0.5 3 25 0.65 5 20 0.5 6 25 0.5 10 80 30 V dc at +85°C 1.3 1 5 0.85 2 10 0.5 5 30 0.7 7 25 0.6 12 35 50 V dc at +85°C 1.5 1 5 0.9 2 10 0.6 3 25 0.75 3 25 0.7 5 40 60V dc at +85°C 2.0 1 5 1.1 2 10 0.6 3 25 0.9 3 25 0.8 5 40 1 12 90 75V dc at +85°C 2.5 1 5 1.3 2 10 0.8 5 30 1.0 3 30 0.9 5 50 100 V dc at +85°C 3.5 1 5 2.1 2 10 1.0 3 25 1.6 3 25 1.2 5 50 125 V dc at +85°C 5.5 1 5 2.3 2 10 1.3 5 25 1.8 3 25 1.6 5 50 Max ESR Ohms 120 Hz Maximum capacitance Max change in percent impedance ohms at -55°C -55°C +85°C +125°C 120 Hz 15 V dc at +125°C 25.0 -42 +8 +12 12.0 -65 +10 +15 7 -60 +20 +45 7.0 -70 +12 +18 7.0 -75 +12 +20 10 -90 +30 +50 20 V dc at +125°C 25.0 -38 +8 +12 15.0 -65 +10 +18 7 -55 +18 +35 7.0 -70 +10 +18 6.0 -72 +10 +20 30 V dc at +125°C 35.0 -25 +8 +15 17.5 -50 +8 +15 7.5 -45 +12 +30 10.0 -50 +8 +15 8.0 -58 +10 +20 40 V dc at +125°C 44.0 -25 +8 +12 20.0 -40 +8 +15 9 -33 +9 +20 15.0 -60 +8 +15 10.0 -58 +8 +15 20 -90 +30 +50 50 V dc at +125°C 66.0 -25 +5 +9 24.0 -35 +6 +10 12 -30 +6 +15 12.0 -45 +6 +10 12.0 -55 +6 +10 65 V dc at +125°C 125 -18 +3 +10 37 -30 +4 +12 20.5 -30 +4 +12 22 -35 +6 +12 15 -40 +6 +12 85 V dc at +125°C 175 -15 +3 +10 47 -25 +5 +12 25 -22 +4 +15 35 -35 +5 +12 20 -35 +6 +12 AC ripple +85°C 40 KHz mA rms 3/ 1250 2100 3200 2600 3100 3200 1200 1800 3200 2500 3000 1050 1800 2900 2100 2750 1050 1650 2900 2100 2750 3200 1050 1650 2500 2100 2750 1050 1650 2200 2100 2750 1050 1650 2000 2100 2750 1/ Dash numbers 1 thru 28 are inactive for new design and are for replacement purposes only. 2/ The complete PIN number shall include symbols to indicate capacitance tolerance and sleeved or unsleeved units. 3/ For ripple current limits at various temperatures, voltages, and frequencies see table III. DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE CODE IDENT NO. DWG NO. A 14933 93026 REV U PAGE 8 TABLE II Voltage. Voltage Derated (+125°C) Volts, dc. 15 20 30 40 50 65 85 Rated (+85°C) Volts, dc. 25 30 50 60 75 100 125 Surge (+85°C) Volts, dc. 28.8 34.5 57.5 69.0 86.3 115.0 144.0 TABLE III Ripple current multipliers vs. Frequency, temperature and applied voltage. 1/ 2/ Frequency of applied ripple current Ambient still air temperature in °C % of 100% 90% +85°C 80% rated 70% peak 66-2/3% voltage Frequency of applied ripple current Ambient still air temperature in °C % of 100% 90% +85°C 80% rated 70% peak 66-2/3% voltage 120 Hz 800 Hz 1 kHz ≤+55 +85 +105 +125 ≤+55 +85 +105 +125 ≤+55 +85 +105 +125 .60 .60 .60 .60 .60 .39 .46 .52 .58 .60 .35 .44 .46 .27 .71 .71 .71 .71 .71 .43 .55 .62 .69 .71 .42 .52 .55 .32 .72 .72 .72 .72 .72 .45 .55 .62 .70 .72 .42 .52 .55 .32 10 kHz 40 kHz 100 kHz ≤+55 +85 +105 +125 ≤+55 +85 +105 +125 ≤+55 +85 +105 +125 .88 .88 .88 .88 .88 .55 .67 .76 .85 .88 .52 .64 .68 .40 1.0 1.0 1.0 1.0 1.0 .63 .77 .87 .97 1.0 .59 .73 .77 .45 1.1 1.1 1.1 1.1 1.1 .69 .85 .96 1.07 1.1 .65 .80 .85 .50 1/ At +125°C, the rated voltage of the capacitors decreases to 66 2/3 of the +85°C rated voltage. 2/ The peak of the applied ac ripple voltage plus the applied dc voltage must not exceed the dc voltage rating of the capacitors. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Point's packaging activity within the Military Department or Defense Agency, or within the Military Department's System Command. Packaging data retrieval is available from the managing Military Department's or Defense Agency's automated packaging files, CDROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature, which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE CODE IDENT NO. DWG NO. A 14933 93026 REV U PAGE 9 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the quality conformance inspection data or certificate of compliance that parts have passed quality conformance inspection with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the group B inspections, or provides a certificate of compliance with group B inspections. d. Requirements for packaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacturer and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have been shown to inhibit the growth of tin whiskers. For additional information in this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin) 6.4 Users of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at [email protected] or if in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4709 or DSN 850-4709. 6.5 Changes from previous issue. The margins of this drawing are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. 6.6 Substitutability data. See table V TABLE V. Substitutability data. Substitute item 9302629-30-31-32-33-34-35-36-37-38-39-40-41-42-- Substitutable for 9302601-02-03-04-05-06-07-08-09-10-11-12-13-14-- DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 Substitute item 9302643-44-45-46-47-48-49-50-51-52-53-54-55-56-- Substitutable for 9302615-16-17-18-19-20-21-22-23-24-25-26-27-28-- SIZE CODE IDENT NO. DWG NO. A 14933 93026 REV U PAGE 10 6.7 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, P. O. Box 3990, Columbus, OH 43218-3990, by e-mail to [email protected], or by telephone (614) 692-4709 or DSN 850-4709. VISHAY EVANS CAPACITOR AVX DSCC drawing PIN vendor A vendor B vendor C 93026- 1/ Similar type Similar type Similar type 01 - -, 29 - ST120 - 25T1 - TWAA127K025 02 - -, 30 - ST560 - 25T2 - TWAB567K025 03 - -, 31 - ST1200 - 25T3 - TWAD128K025 04 - -, 32 - ST1800 - 25T4 - TWAE188K025 05 - -, 33 - ST100 - 30T1 - TWAA107K030 06 - -, 34 - ST470 - 30T2 - TWAB477K030 07 - -, 35 - ST1000 - 30T3 - TWAD108K030 08 - -, 36 - ST1500 - 30T4 - TWAE158K030 09 - -, 37 - ST68 - 50T1 - TWAA686K050 10 - -, 38 - ST220 - 50T2 - TWAB227K050 11 - -, 39 - ST470 - 50T3 - TWAD477K050 12 - -, 40 - ST680 - 50T4 - HCD050681 TWAE687K050 13 - -, 41 - ST47 - 60T1 - TWAA476K060 14 - -, 42 - ST150 - 60T2 - TWAB157K060 15 - -, 43 - ST390 - 60T3 - TWAD397K060 16 - -, 44 - ST560 - 60T4 - HCD060561 TWAE567K060 17 - -, 45 - ST33 - 75T1 - TWAA336K075 18 - -, 46 - ST110 - 75T2 - HCB075111 TWAB117K075 19 - -, 47 - ST330 - 75T3 - TWAD337K075 20 - -, 48 - ST470 - 75T4 - HCD075471 TWAE477K075 21 - -, 49 - ST15 - 100T1 - TWAA156K100 22 - -, 50 - ST68 - 100T2 - HCB100680 TWAB686K100 23 - -, 51 - ST150 - 100T3 - TWAD157K100 24 - -, 52 - ST220 - 100T4 - HCD100221 TWAE227K100 25 - -, 53 - ST10 - 125T1 - TWAA106K125 26 - -, 54 - ST47 - 125T2 - TWAB476K125 27 - -, 55 - ST100 - 125T3 - TWAD107K125 28 - -, 56 - ST150 - 125T4 - HCD125151 TWAE157K125 57 - ST1100 - 25L2 - 58 - ST950 - 30L2 - 59 - ST450 - 50L2 - 60 - ST370 - 60L2 - 61 - ST250 - 75L2 - 62 - ST120 - 100L2 - 63 - ST90 - 125L2 - 64 - ST2200 – 25T4 - TWAE228K025 65 - ST1000 – 60T4 - TWAE108M060 1/ Parts must be purchased to the DSCC PIN to assure that all the performance requirements and tests are met. DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE CODE IDENT NO. DWG NO. A 14933 93026 REV U PAGE 11 Vendor Vendor CAGE Vendor name and address A 05079 Vishay Intertechnology Inc 2813 West Road Bennington, VT 05201-5017 B 06MN5 Evans Capacitor Company 72 Boyd Avenue East Providence, RI 02914-1202 C 17554 AVX Tantalum Corporation 401 Hill Street Biddeford, ME 04005-4327 DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE CODE IDENT NO. DWG NO. A 14933 93026 REV U PAGE 12