HD-15531 TM CMOS Manchester Encoder-Decoder March 1997 Features Description • Support of MIL-STD-1553 The Intersil HD-15531 is a high performance CMOS device intended to service the requirements of MIL-STD-1553 and similar Manchester II encoded, time division multiplexed serial data protocols. This LSI chip is divided into two sections, an Encoder and a Decoder. These sections operate independently of each other, except for the master reset and word length functions. This circuit provides many of the requirements of MIL-STD-1553. The Encoder produces the sync pulse and the parity bit as well as the encoding of the data bits. The Decoder recognizes the sync pulse and identifies it as well as decoding the data bits and checking parity. • Data Rate (15531B) . . . . . . . . . . . . . . . .2.5 Megabit/Sec • Data Rate (15531) . . . . . . . . . . . . . . . . .1.25 Megabit/Sec • Variable Frame Length to 32 Bits • Sync Identification and Lock-In • Separate Manchester II Encode, Decode • Low Operating Power . . . . . . . . . . . . . . . . . 50mW at 5V The HD-15531 also surpasses the requirements of MILSTD-1553 by allowing the word length to be programmable (from 2 to 28 data bits). A frame consists of three bits for sync followed by the data word (2 to 28 data bits) followed by one bit of parity, thus, the frame length will vary from 6 to 32 bit periods. This chip also allows selection of either even or odd parity for the Encoder and Decoder separately. Ordering Information TEMP. RANGE (oC) 1.25MBIT /SEC PDIP -40 to 85 - CERDIP -40 to 85 HD1-15531-9 HD1-15531B-9 F40.6 -55 to 125 HD1-15531-8 HD1-15531B-8 F40.6 -55 to 125 59629054901MQA HD1-15531 -55 to 125 59629054902MQA HD1-15531B PACKAGE DESC (CERDIP) 2.5MBIT /SEC PKG. NO. HD3-15531B-9 E40.6 This integrated circuit is fully guaranteed to support the 1MHz data rate of MIL-STD-1553 over both temperature and voltage. For high speed applications the 15531B will support a 2.5 Megabit/sec data rate. F40.6 The HD-15531 can also be used in many party line digital data communications applications, such as a local area network or an environmental control system driven from a single twisted pair of fiber optic cable throughout a building. F40.6 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved 1 FN2961.1 HD-15531 Pinout HD-15531 (CERDIP, PDIP) TOP VIEW VCC 1 40 COUNT C1 VALID WORD 2 39 COUNT C4 TAKE DATA’ 3 38 DATA SYNC TAKE DATA 4 37 ENCODER CLK SERIAL DATA OUT 5 36 COUNT C3 SYNCHR DATA 6 35 NC SYNCHR DATA SEL 7 34 ENCODER SHIFT CLK SYNCHR CLK 8 33 SEND CLK IN DECODER CLK 9 32 SEND DATA SYNCHR CLK SEL 10 31 ENCODER PARITY SEL BIPOLAR ZERO IN 11 30 SYNC SEL BIPOLAR ONE IN 12 29 ENCODER ENABLE UNIPOLAR DATA IN 13 28 SERIAL DATA IN DECODER SHIFT CLK 14 27 BIPOLAR ONE OUT TRANSITION SEL 15 26 OUTPUT INHIBIT NC 16 25 BIPOLAR ZERO OUT COMMAND SYNC 17 24 ÷ 6 OUT 23 COUNT C2 DECODER PARITY SEL 18 DECODER RESET 19 22 MASTER RESET 21 GND COUNT C0 20 Block Diagrams ENDODER GND 21 VCC 1 MASTER RESET 22 OUTPUT INHIBIT SEND CLK IN 33 26 ÷ 6 OUT 24 ÷2 CHARACTER FORMER ÷6 27 BIPOLAR ONE OUT 25 BIPOLAR ZERO OUT ENCODER CLK 37 BIT COUNTER 32 20 C0 40 23 C1 C2 36 C3 39 C4 34 SEND DATA 28 29 SERIAL DATA IN ENCODER SHIFT CLK 2 30 31 SYNC SELECT ENCODER ENABLE ENCODER PARITY SELECT HD-15531 DECODER SYNCHRONOUS DATA SELECT UNIPOLAR DATA IN BIPOLAR ONE IN BIPOLAR ONE IN 7 8 SYNCHRONOUS DATA 13 12 4 TRANSITION FINDER 11 DATA SELECT GATE 17 CHARACTER IDENTIFIER COMMAND SYNC DATA SYNC 5 DECODER CLK DECODER CLK SELECT SYNCHRONOUS CLK SYNCHRONOUS CLK SELECT MASTER RESET TAKE DATA 9 15 SYNCHRONIZER CLOCK SELECT DATA 2 PARITY CHECK 16 BIT RATE CLK SERIAL DATA OUT VALID WORD PARITY SELECT 8 14 10 DECODER SHIFT CLK 22 DECODER RESET 19 3 BIT COUNTER 20 40 C0 23 C1 36 C2 TAKE DATA’ 39 C3 C4 Pin Description PIN NUMBER TYPE 1 NAME VCC SECTION DESCRIPTION Both Positive supply pin. A 0.1µF decoupling capacitor from VCC (pin 1) to GROUND (pin 21) is recommended. 2 O VALID WORD Decoder Output high indicates receipt of a valid word, (valid parity and no Manchester errors). 3 O TAKE DATA’ Decoder A continuous, free running signal provided for host timing or data handling. When data is present on the bus, this signal will be synchronized to the incoming data and will be identical to TAKE DATA. 4 O TAKE DATA Decoder Output is high during receipt of data after identification of a valid sync pulse and two valid Manchester bits. 5 O SERIAL DATA OUT Decoder Delivers received data in correct NRZ format. 6 I SYNCHRONOUS DATA Decoder Input presents Manchester data directly to character identification logic. SYNCHRONOUS DATA SELECT must be held high to use this input. If not used, this pin must be held high. 7 I SYNCHRONOUS DATA SELECT Decoder In high state allows the synchronous data to enter the character identification logic. Tie this input low for asynchronous data. 8 I SYNCHRONOUS CLOCK Decoder Input provides externally synchronized clock to the decoder, for use when receiving synchronous data. This input must be tied high when not in use. 9 I DECODER CLOCK Decoder Input drives the transition finder, and the synchronizer which in turn supplies the clock to the balance of the decoder. Input a frequency equal to 12X the data rate. 10 I SYNCHRONOUS CLOCK SELCT Decoder In high state directs the SYNCHRONOUS CLOCK to control the decoder character identification logic. A low state selects the DECODER CLOCK. 11 I BIPOLAR ZERO IN Decoder A high input should be applied when the bus is in its negative state. This pin must be held high when the unipolar input is used. 12 I BIPOLAR ONE IN Decoder A high input should be applied when the bus is in its positive state. This pin must he held low when the unipolar input is used. 13 I UNIPOLAR DATA IN Decoder With pin 11 high and pin 12 low, this pin enters unipolar data into the transition finder circuit. If not used this input must be held low. 3 HD-15531 Pin Description PIN NUMBER TYPE 14 O 15 I 16 (Continued) NAME SECTION DESCRIPTION DECODER SHIFT CLOCK Decoder Output which delivers a frequency (DECODER CLOCK + 1 2), synchronous by the recovered serial data stream. TRANSITION SELECT Decoder A high input to this pin causes the transition finder to synchronize on every transition of input data. A low input causes the transition finder to synchronize only on mid-bit transitions. NC Blank Not connected. 17 O COMMAND SYNC Decoder Output of a high from this pin occurs during output of decoded data which was preceded by a Command (or Status) synchronizing character. 18 I DECODER PARITY SELECT Decoder An input for parity sense, calling for even parity with input high and odd parity with input low. 19 I DECODER RESET Decoder A high input to this pin during a rising edge of DECODER SHIFT CLOCK resets the decoder bit counting logic to a condition ready for a new word. 20 I COUNT C0 Both One of five binary inputs which establish the total bit count to be encoded or decoded. GROUND Both Supply pin. A high on this pin clears 2:1 counters in both encoder and decoder, and resets the ÷ 6 circuit. 21 22 I MASTER RESET Both 23 I COUNT C2 Both 24 O ÷ 6 OUT Encoder Output from 6:1 divider which is driven by the ENCODER CLOCK. 25 O BIPOLAR ZERO OUT Encoder An active low output designed to drive the zero or negative sense of a bipolar line driver. 26 I OUTPUT INHIBIT Encoder A low on this pin forces pin 25 and 27 high, the inactive states. 27 O BIPOLAR ONE OUT Encoder An active low output designed to drive the one or positive sense of a bipolar line driver. 28 I SERIAL DATA IN Encoder Accepts a serial data stream at a data rate equal to ENCODER SHIFT CLOCK. 29 I ENCODER ENABLE Encoder A high on this pin initiates the encode cycle. (Subject to the preceding cycle being complete). 30 I SYNC SELECT Encoder Actuates a Command sync for an input high and Data sync for an input low. 31 I ENCODER PARITY SELECT Encoder Sets transmit parity odd for a high input, even for a low input. 32 O SEND DATA Encoder Is an active high output which enables the external source of serial data. 33 I SEND CLOCK IN Encoder Clock input at a frequency equal to the data rate X2, usually driven by ÷ 6 output. 34 O ENCODER SHIFT CLOCK Encoder Output for shifting data into the Encoder. The Encoder samples SDI pin-28 on the low-to-high transition of ESC. 35 See pin 20. NC Blank Not connected. Both See pin 20. 36 I COUNT C3 37 I ENCODER CLOCK Encoder Input to the 6:1 divider, a frequency equal to 12 times the data rate is usually input here. 38 O DATA SYNC Decoder Output of a high from this pin occurs during output of decoded data which was preceded by a data synchronizing character. 39 I COUNT C4 Both See pin 20. 40 I COUNT C1 Both See pill 20. 4 HD-15531 Encoder Operation be clocked into the SERIAL DATA input with every high-tolow transition of the ENCODER SHIFT CLOCK 3 - 4 so it can be sampled on the low-to-high transition. After the sync and Manchester II encoded data are transmitted through the BIPOLAR ONE and BIPOLAR ZERO outputs, the Encoder adds on an additional bit with the parity for that word 5 . If ENCODER ENABLE is held high continuously, consecutive words will be encoded without an interframe gap. ENCODER ENABLE must go low by time 5 (as shown) to prevent a consecutive word from being encoded. At any time a low on OUTPUT INHIBIT input will force both bipolar outputs to a high state but will not affect the Encoder in any other way. The Encoder requires a single clock with a frequency of twice the desired data rate applied at the SEND CLOCK input. An auxiliary divide by six counter is provided on chip which can be utilized to produce the SEND CLOCK by dividing the DECODER CLOCK. The frame length is set by programming the COUNT inputs. Parity is selected by programming ENCODER PARITY SELECT high for odd parity or low for even parity. The Encoder’s cycle begins when ENCODER ENABLE is high during a falling edge of ENCODER SHIFT CLOCK 1 . This cycle lasts for one word length or K + 4 ENCODER SHIFT CLOCK periods, where K is the number of bits to be sent. At the next low-to-high transition of the ENCODER SHIFT CLOCK, a high SYNC SELECT input actuates a Command sync or a low will produce a Data sync for the word 2 . When the Encoder is ready to accept data, the SEND DATA output will go high for K ENCODER SHIFT CLOCK periods 4 . During these K periods the data should TIMING 0 1 2 3 4 To abort the Encoder transmission, a positive pulse must be applied at MASTER RESET. Any time after or during this pulse, a low-to-high transition on SEND CLOCK clears the internal counters and initializes the Encoder for a new word. 5 6 7 N-4 N-3 N-2 N-1 N SEND CLOCK ENCODER SHIFT CLOCK ENCODER ENABLE DON’T CARE SYNC SELECT VALID DON’T CARE SEND DATA SERIAL DATA IN MSB BIT K-1 BIT K-2 BIT K-3 BIT K-4 BIT K-5 BIT 4 BIT 3 BIPOLAR ONE OUT 1ST HALF 2ND HALF BIPOLAR ZERO OUT SYNC 1 2 SYNC BIT 2 BIT 1 MSB BIT K-1 BIT K-2 BIT K-3 BIT K-4 BIT 4 BIT 3 BIT 2 BIT 1 PARITY MSB BIT 4 BIT 3 BIT 2 BIT 1 PARITY BIT K-1 BIT K-2 BIT K-3 BIT K-4 3 4 5 FIGURE 1. ENCODER Decoder Operation To operate the Decoder asynchronously requires a single clock with a frequency of 12 times the desired data rate applied at the DECODER CLOCK input. To operate the Decoder synchronously requires a SYNCHRONOUS CLOCK at a frequency 2 times the data rate which is synchronized with the data at every high-to-low transition applied to the SYNCHRONOUS CLK input. The Manchester II coded data can be presented to the Decoder asynchronously in one of two ways. The BIPOLAR ONE and BIPOLAR ZERO inputs will accept data from a comparator sensed transformer coupled bus as specified in Military Spec 1553. The UNIPOLAR DATA input can only accept noninverted Manchester II coded data. (e.g., from BIPOLAR ONE OUT on an Encoder through an inverter to Unipolar Data Input). The Decoder is free running and continuously monitors its data input lines for a valid sync character and two valid Manchester data bits to start an output cycle. When a valid sync is recognized 1 , the type of sync is indicated by a high level at either COMMAND SYNC or DATA SYNC output. If the sync character was a command sync the COMMAND SYNC output will go high 2 and remain high for K SHIFT CLOCK periods 3 , where K is the number of bits to be received. If the sync character was a data sync, the DATA SYNC output will go high. The TAKE DATA output will go high and remain high 2 - 3 while the Decoder is transmit- 5 HD-15531 ting the decoded data through SERIAL DATA OUT. The decoded data available at SERIAL DATA OUT is in NRZ format. The DECODER SHIFT CLOCK is provided so that the decoded bits can get shifted into an external register on every low-to-high transition of this clock 2 - 3 . Note that DECODER SHIFT CLOCK may adjust its phase up until the time that TAKE DATA goes high. on VALID WORD output 4 indicates a successful reception of a word without any Manchester or parity errors. At this time the Decoder is looking for a new sync character to start another output sequence. VALID WORD will go low approximately K + 4 DECODER SHIFT CLOCK periods after it goes high, if not reset low sooner by a valid sync and two valid Manchester bits as shown 1 . After all K decoded bits have been transmitted 3 the data is checked for parity. A high input on DECODER PARITY SELECT will set the Decoder to check for even parity or a low input will set the Decoder to check for odd parity. A high At any time in the above sequence a high input on DECODER RESET during a low-to-high transition of DECODER SHIFT CLOCK will abort transmission and initialize the Decoder to start looking for a new sync character. TIMING 0 1 2 3 4 5 6 7 8 N-3 N-2 N-1 N BIT 3 BIT 2 BIT 1 PARITY BIT 3 BIT 2 BIT 1 PARITY SYNCHRONOUS CLOCK DECODER SHIFT CLOCK BIPOLAR ONE IN BIPOLAR ZERO IN 1ST HALF 2ND HALF MSB BIT K-1 BIT K-2 BIT K-3 BIT K-4 BIT K-5 SYNC SYNC MSB BIT K-1 BIT K-2 BIT K-3 BIT K-4 BIT K-5 TAKE DATA COMMAND SYNC DATA SYNC SERIAL DATA OUT UNDEFINED MSB BITK-1 BITK-2 BITK-3 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 (MAY BE HIGH FROM PREVIOUS RECEPTION) VALID WORD 1 2 3 FIGURE 2. DECODER 6 4 HD-15531 Frame Counter PIN WORD DATA BITS FRAME LENGTH (BIT PERIODS) C4 C3 C2 C1 C0 2 6 L L H L H 3 7 L L H H L 4 8 L L H H H 5 9 L H L L L 6 10 L H L L H 7 11 L H L H L 8 12 L H L H H 9 13 L H H L L 10 14 L H H L H 11 15 L H H H L 12 16 L H H H H 13 17 H L L L L 14 18 H L L L H 15 19 H L L H L 16 20 H L L H H 17 21 H L H L L 18 22 H L H L H 19 23 H L H H L 20 24 H L H H H 21 25 H H L L L 22 26 H H L L H 23 27 H H L H L 24 28 H H L H H 25 29 H H H L L 26 30 H H H L H 27 31 H H H H L 28 32 H H H H H NOTE: 1. The above table demonstrates all possible combinations of frame lengths ranging from 6 to 32 bits. The pin word described here is common to both the Encoder and Decoder. 7 HD-15531 VALID WORD VCC TAKE DATA COUNT C1 SYNC DATA SYNC DATA SELECT SYNC CLOCK DECODER CLOCK SYNC CLOCK SELECT BIPOLAR ZERO IN NC BIPOLAR ONE IN UNIPOLAR DATA IN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 COUNT C4 DATA SYNC NC COUNT C3 ENCODER PARITY SEL. SYNC SELECT ENCODER ENABLE BIPOLAR ONE OUT INHIBIT OUTPUT TRANSITION SELECT BIPOLAR ZERO OUT COMMAND SYNC A DECODER PARITY SELECT B CK H 74164 COUNT C0 A B CK 74164 OH SH/LD CK SI OH SH/LD CK SI 74165 74165 PARALLEL OUT COUNT C2 MASTER RESET PARALLEL IN FIGURE 3. HOW TO MAKE OUR MTU LOOK LIKE A MANCHESTER ENCODED UART Typical Timing Diagrams for a Manchester Encoded UART ENCODER ENABLE SYNC SELECT VALID VALID PARALLEL IN BIPOLAR ONE OUT P BIPOLAR ZERO OUT P SYNC MSB LSB PARITY FIGURE 4. ENCODER TIMING 8 HD-15531 SYNC MSB LSB PARITY BIPOLAR ONE IN P BIPOLAR ZERO IN P COMMAND SYNC PARALLEL OUT VALID WORD VALID VALID FROM PREVIOUS RECEPTION FIGURE 5. DECODER TIMING MIL-STD-1553 Words, and Data. Terminals respond with Status Words, and Data. Each word is preceded by a synchronizing pulse, and The 1553 Standard defines a time division multiplexed data bus for application within aircraft. The bus is defined to be bipolar, and encoded in a Manchester II format, so no DC component appears on the bus. This allows transformer coupling and excellent isolation among systems and their environment. followed by parity bit, occupying a total of 20µs. The word formats are shown in Figure 4. The special abbreviations are as follows: The HD-15531 supports the full bipolar configuration, assuming a bus driver configuration similar to that in Figure 1. Bipolar inputs from the bus, like Figure 2, are also accommodated. The signaling format in MIL-STD-1553 is specified on the assumption that the network of 32 or fewer terminals are controlled by a central control unit by means of Command- P Parity, which is defined to be odd, taken across all 17 bits. R/T Receive on logical zero, transmit on ONE. ME Message Error if logical 1. TF Terminal Flag, if set, calls for controller to request self-test data. BUS + - “1” “1” “1” REF “0” REF + “0” FIGURE 6. SIMPLIFIED MIL-STD-1553 DRIVER FIGURE 7. SIMPLIFIED MIL-STD-1553 RECEIVER 9 “0” HD-15531 COMMAND SYNC DATA SYNC BIT BIT BIT PERIOD PERIOD PERIOD LOGICAL ONE DATA LOGICAL ZERO DATA FIGURE 8. MIL-STD-1553 CHARACTER FORMATS 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 COMMAND WORD (FROM CONTROLLER TO TERMINAL) 5 SYNC 1 TERMINAL ADDRESS 5 5 1 SUB ADDRESS /MODE DATA WORD COUNT P R/T DATA WORD (SENT EITHER DIRECTION) 1 16 SYNC DATA WORD P STATUS WORD (FROM TERMINAL TO CONTROLLER) 5 SYNC 1 TERMINAL ADDRESS 9 1 1 CODE FOR FAILURE MODES TF P FIGURE 9. MIL-STD-1553 WORD FORMATS NOTE: 1. This page is a summary of MIL-STD-1553 and is not intended to describe the operation of the HD-15531. 10 HD-15531 Absolute Maximum Ratings Thermal Information Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V Input, Output or I/O Voltage . . . . . . . . . . . GND -0.5V to VCC +0.5V ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 Thermal Resistance (Typical) θJA θJC CERDIP Package . . . . . . . . . . . . . . . . . . 35oC/W 9oC/W PDIP Package . . . . . . . . . . . . . . . . . . . . . 50oC/W N/A Storage Temperature Range . . . . . . . . . . . . . . . . .-65oC to +150oC Maximum Junction Temperature Ceramic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Plastic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150oC Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . +300oC Operating Conditions Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V Operating Temperature Range (TA) HD-15531-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to +85oC HD-15531-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to +125oC Encoder/Decoder Clock Rise Time (TECR, TDCR) . . . . . . . 8ns Max Encoder/Decoder Clock Fall Time (TECF, TDCF) . . . . . . . . 8ns Max Die Characteristics Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 Gates Sync. Transition Span (TD2). . . . . . . . . . . 18 TDC Typical, (Note 1) Short Data Transition Span (TD4). . . . . . . . 6 TDC Typical, (Note 1) Long Data Transition Span (TD5) . . . . . . . 12 TDC Typical, (Note 1) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. DC Electrical Specifications VCC = 5.0V ±10%, TA = -40oC to +85Co (HD-15531-9) TA = -55oC to +125C o (HD-15531-8) PARAMETER SYMBOL TEST CONDITIONS MIN MAX UNITS Input LOW Voltage V IL VCC = 4.5V and 5.5V - 0.2 VCC V Input HIGH Voltage VIH VCC = 4.5V and 5.5V 0.7 VCC - V Input LOW Clock Voltage VILC VCC = 4.5V and 5.5V - GND +0.5 V Input HIGH Clock Voltage VIHC VCC = 4.5V and 5.5V VCC -0.5 - V Output LOW Voltage VOL IOL = +1.8mA, VCC = 4.5V (Note 2) - 0.4 V Output HIGH Voltage V OH IOH = -3.0mA, VCC = 4.5V (Note 2) 2.4 - V Input Leakage Current II VI = VCC or GND, VCC = 5.5V -1.0 +1.0 µA Standby Supply Current ICCSB VIN = VCC = 5.5V, Outputs Open - 2 mA Operating Power Supply Current ICCOP VIN = VCC = 5.5V, f = 15MHz, Outputs Open - 10 mA (Note 3) - - - Functional Test FT NOTES: 1. TDC = Decoder clock period = 1/FDC. 2. Interchanging of force and sense conditions is permitted. 3. Tested as follows: f = 15MHz, VIH = 70% VCC, VIL = 20% VCC, CL = 50pF, VOH ≥ VCC/2 and VOL ≤ VCC/2. Capacitance TA = +25oC, Frequency = 1MHz SYMBOL PARAMETER TYP UNITS C IN Input Capacitance 25 pF C OUT Output Capacitance 25 pF 11 TEST CONDITIONS All measurements are referenced to device GND HD-15531 AC Electrical Specifications VCC = 5V ±10%, TA = -40oC to +85oC (HD-15530-9) TA = -55oC to +125oC (HD-15530-8) HD-15531 SYMBOL PARAMETER HD-15531B MIN MAX MIN MAX UNITS TEST CONDITIONS (NOTE 2) - 15 - 30 MHz VCC = 4.5V and 5.5V, C L = 50pF ENCODER TIMING FEC Encoder Clock Frequency Send Clock Frequency - 2.5 - 5.0 MHz VCC = 4.5V and 5.5V, C L = 50pF FED Encoder Data Rate - 1.25 - 2.5 MHz VCC = 4.5V and 5.5V, C L = 50pF TMR Master Reset Pulse Width 150 - 150 - ns VCC = 4.5V and 5.5V, C L = 50pF TE1 Shift Clock Delay - 125 - 80 ns VCC = 4.5V and 5.5V, C L = 50pF TE2 Serial Data Setup 75 - 50 - ns VCC = 4.5V and 5.5V, C L = 50pF TE3 Serial Data Hold 75 - 50 - ns VCC = 4.5V and 5.5V, C L = 50pF TE4 Enable Setup 90 - 90 - ns VCC = 4.5V and 5.5V, C L = 50pF TE5 Enable Pulse Width 100 - 100 - ns VCC = 4.5V and 5.5V, C L = 50pF TE6 Sync Setup 55 - 55 - ns VCC = 4.5V and 5.5V, C L = 50pF TE7 Sync Pulse Width 150 - 150 - ns VCC = 4.5V and 5.5V, C L = 50pF TE8 Send Data Delay 0 50 0 50 ns VCC = 4.5V and 5.5V, C L = 50pF TE9 Bipolar Output Delay - 130 - 130 ns VCC = 4.5V and 5.5V, C L = 50pF TE10 Enable Hold 10 - 10 - ns VCC = 4.5V and 5.5V, C L = 50pF TE11 Sync Hold 95 - 95 - ns VCC = 4.5V and 5.5V, C L = 50pF - 15 - 30 MHz VCC = 4.5V and 5.5V, C L = 50pF FESC DECODER TIMING FDC Decoder Clock Frequency FDS Decoder Sync Clock - 2.5 - 5.0 MHz VCC = 4.5V and 5.5V, C L = 50pF FDD Decoder Data Rate - 1.25 - 2.5 MHz VCC = 4.5V and 5.5V, C L = 50pF TDR Decoder Reset Pulse Width 150 - 150 - ns VCC = 4.5V and 5.5V, C L = 50pF TDRS Decoder Reset Setup Time 75 - 75 - ns VCC = 4.5V and 5.5V, C L = 50pF TDRH Decoder Reset Hold Time 10 - 10 - ns VCC = 4.5V and 5.5V, C L = 50pF TMR Master Reset Pulse 150 - 150 - ns VCC = 4.5V and 5.5V, C L = 50pF TD1 Bipolar Data Pulse Width TDC + 10 (Note 1) - TDC + 10 (Note 1) - ns VCC = 4.5V and 5.5V, C L = 50pF TD3 One Zero Overlap - TDC - 10 (Note 1) - TDC - 10 (Note 1) ns VCC = 4.5V and 5.5V, C L = 50pF TD6 Sync Delay (ON) -20 110 -20 110 ns VCC = 4.5V and 5.5V, C L = 50pF TD7 Take Data Delay (ON) 0 110 0 110 ns VCC = 4.5V and 5.5V, C L = 50pF TD8 Serial Data Out Delay - 80 - 80 ns VCC = 4.5V and 5.5V, C L = 50pF TD9 Sync Delay (OFF) 0 110 0 110 ns VCC = 4.5V and 5.5V, C L = 50pF TD10 Take Data Delay (OFF) 0 110 0 110 ns VCC = 4.5V and 5.5V, C L = 50pF TD11 Valid Word Delay 0 110 0 110 ns VCC = 4.5V and 5.5V, C L = 50pF TD12 Sync Clock to Shift Clock Delay - 75 - 75 ns VCC = 4.5V and 5.5V, C L = 50pF TD13 Sync Data Setup 75 - 75 - ns VCC = 4.5V and 5.5V, C L = 50pF NOTES: 1. TDC = Decoder clock period = 1/FDC. 2. AC Testing as follows: Input levels: VIH = 70% V CC, VIL = 20% VCC; Input rise/fall times driven at 1ns/V; Timing Reference levels: V CC/2; Output load: CL = 50pF. 12 HD-15531 Timing Waveforms SEND CLOCK TE1 ENCODER SHIFT CLOCK TE2 SERIAL DATA IN TE3 VALID VALID SEND CLOCK TE1 TE10 ENCODER SHIFT CLOCK TE4 ENCODER ENABLE TE11 TE5 TE6 VALID SYNC SELECT TE7 ENCODER SHIFT CLOCK TE8 SEND DATA SEND CLOCK TE9 BIPOLAR ONE OUT OR BIPOLAR ZERO OUT FIGURE 10. ENCODER TIMING 13 HD-15531 Timing Waveforms (Continued) NOTE: UNIPOLAR IN = 0, FOR NEXT DIAGRAMS. BIT PERIOD BOI BIT PERIOD BIT PERIOD TD1 TD2 TD3 TD3 TD1 BZI TD2 COMMAND SYNC TD1 BOI TD2 TD3 TD3 TD1 BZI DATA SYNC BOI BZI TD2 TD1 TD1 TD3 TD3 TD3 TD3 TD2 TD3 TD1 TD5 TD4 ONE TD5 TD4 ZERO ONE NOTE: BIPOLAR ONE IN = 0, BIPOLAR ZERO IN = 1, FOR NEXT DIAGRAMS. TD2 UI TD2 COMMAND SYNC TD2 UI TD2 DATA SYNC UI TD4 TD5 ONE TD5 ZERO TD4 ONE FIGURE 11. DECODER TIMING 14 TD4 ONE HD-15531 Timing Waveforms (Continued) DECODER SHIFT CLOCK TD6 COMMAND/DATA SYNC TD7 TAKE DATA DECODER SHIFT CLOCK TD8 DATA BIT SERIAL DATA OUT TD10 DECODER SHIFT CLOCK TD9 COMMAND/DATA SYNC TD10 TAKE DATA TD11 VALID WORD DECODER SHIFT CLOCK TDRS TDR DECODER RESET TDRH SYNCHRONOUS INPUT (WITH EXTERNAL BIT SYNCHRONIZATION) SYNCHRONOUS CLOCK IN TD12 DECODER SHIFT CLOCK SYNCHRONOUS CLOCK IN TD13 TD13 SYNCHRONOUS DATA IN MANCHESTER PHASES FIGURE 12. DECODER TIMINGS 15 TD13 TD13 HD-15531 Test Load Circuit AC Testing Input, Output Waveform DUT INPUT CL (NOTE 1) OUTPUT VIH VOH 50% 50% VIL VOL FIGURE 14. FIGURE 13. NOTE: NOTE: 1. AC Testing: All input signals must switch between VIL and VIH, input rise and fall times are driven at 1ns per volt. 1. Includes stray and jig capacitance. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation 7585 Irvine Center Drive Suite 100 Irvine, CA 92618 TEL: (949) 341-7000 FAX: (949) 341-7123 Intersil Corporation 2401 Palm Bay Rd. Palm Bay, FL 32905 TEL: (321) 724-7000 FAX: (321) 724-7946 EUROPE Intersil Europe Sarl Ave. William Graisse, 3 1006 Lausanne Switzerland TEL: +41 21 6140560 FAX: +41 21 6140579 16 ASIA Intersil Corporation Unit 1804 18/F Guangdong Water Building 83 Austin Road TST, Kowloon Hong Kong TEL: +852 2723 6339 FAX: +852 2730 1433