1040 Sliding Mall Front - Architectural Detail Manual

APRIL, 2009
1040® SLIDING MALL FRONT
INDEX
INDEX...................................................................................................1
ELEVATIONS/VERTICAL SECTION DETAILS................................... 2
HORIZONTAL SECTION DETAILS..................................................... 3
EGRESS DOOR................................................................................ 4-5
STACK AREA LAYOUT.................................................................... 6-8
SIZE LIMITATIONS.............................................................................. 9
HARDWARE.......................................................................................10
LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL
THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR.
Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses
(
) are millimeters unless otherwise noted.
The following metric (SI ) units are found in these details:
m –meter
cm – centimeter
mm –millimeter
s –second
Pa –pascal
MPa –megapascal
© Kawneer Company, Inc., 2009
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-10
1
Kawneer reserves the right to change configurations without prior notice when deemed necessary for product
improvement.
kawneer.com
1040 SLIDING MALL FRONT
2
APRIL, 2009
ELEVATIONS/VERTICAL SECTION DETAILS
EC 97911-10
SCALE 3" = 1'-0"
3
3
2
4
10
9
8
4
ELEVATIONS ARE NUMBERED KEYED BELOW AND ON PAGE 3.
3
3
3
SURFACE HEAD TRACK
APPLICATION
RECESSED HEAD TRACK
APPLICATION
RECESSED HEAD TRACK
APPLICATION
HEAD
TRACK
1/2"
(12.7)
1/2"
(12.7)
2-9/32"
(57.9)
PANEL
TOP
RAIL
PANEL
TOP
RAIL
5/8"
(15.9)
1-7/8"
(47.6)
3-1/2"
(88.9)
DRAINING
TRACK
5/16”
(7.9)
NOM.
RECESSED
TRACK
SILL TRACK
1-1/2"
(38.1)
MIN.
CHASE
DEPTH
SURFACE
TRACK
4
PANEL
BOTTOM
RAIL
3-25/32”
(96.0)
PANEL
BOTTOM
RAIL
FINISH FLOOR
TRACK
SUPPORT
1-5/16"
(33.3)
INTERMEDIATE
HORIZONTAL
1-3/4"
(44.5)
4
4-15/32"
(113.5)
4 -15/32"
(113.5)
PANEL
BOTTOM
RAIL
RAMP
ADAPTER
INTERMEDIATE
HORIZONTAL
1-3/4"
(44.5)
4
5
SILL TRACK
5-1/2" MIN. CHASE WIDTH
(139.7)
91-283
COMPRESSIBLE
SHIM
DRAIN CONNECTIONS TO 60-110 TO BE BY OTHERS 1" (25.4)
TO 1-1/4"(31.8) O.D. DRAIN TUBING RECOMMENDED EVERY
15' (4.572 METERS) AND AT EACH END.
60-110
DRAIN
TUBE
3” (76.2)
MIN CHASE
DEPTH
NOTE: PROPER SUPPORT MUST BE
PROVIDED FOR FLOOR AND
HEAD TRACK INCLUDING THE
STACK AREA.
5
2-1/4"
(57.1)
NOTE: FOR PROPER PANEL OPERATION
ON SURFACE TRACK APPLICATIONS,
THE FINISH FLOOR MUST BE LEVEL
WITHIN 1/8" PER EACH PANEL WIDTH
AND WITHIN 1/2" OVER THE ENTIRE
TRACK AREA.
PANEL
TOP
RAIL
15/16”
(23.8)
NOM.
2-9/32"
(57.9)
WEATHERING
ANGLE OPTIONAL
HEAD
TRACK
1/2"
(12.7)
2-9/32"
(57.9)
HEAD
TRACK
5/8"
(15.9)
1-3/4"
(44.5)
1/4"
(6.4)
DRAIN
TRACK
SUPPORT
5 1/2” MIN. CHASE WIDTH
(139.7)
kawneer.com
© Kawneer Company, Inc., 2009
1
7
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1
5
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
*POSSIBLE TRACK CONDITION
VARY WIDELY. CONSULT THE
KAWNEER REPRESENTATIVE FOR
TRACK APPLICATION NOT SHOWN
IN THESE DETAILS.
1040® SLIDING MALL FRONT
APRIL, 2009
EC 97911-10
HORIZONTAL SECTION DETAILS
SCALE 3" = 1'-0"
1
2
CLOSING PANEL
1
1-1/8” 1-1/8”
(28.6) (28.6)
3/4”
(19.1)
1-3/4”
(44.5)
3-3/4”
(95.3)
1-3/4”
(44.5)
(69.9)
*2-3/4”
5/16”
(7.9)
NARROW TERMINATOR IS
REQUIRED. WHEN LAST
PANEL IS LOCKED IN PLACE
BY HINGED PANEL OF
STORAGE POCKET.
RECESSED
JAMB
CHANNEL
2-9/32”
(57.9)
1-9/16”
(39.7)
TRACK
CL
TRACK
CL
4-1/32”
(102.4)
TERMINATOR
STILE
2-9/32”
(57.9)
1/4”
(6.4)
1”
(25.4)
*
TERMINATOR
STILE
1/8”
(3.2)
NOM.
1-3/4”
(44.5)
2-9/32”
(57.9)
4-1/32”
(102.4)
RECEIVING JAMB
ASSEMBLY
1-9/16”
(39.7)
TRACK
CL
5/16”
(7.9)
3/4”
(19.1)
2
4-1/2”
(114.5)
ALTERNATE SURFACE
APPLIED JAMB CHANNEL
4-1/2”
(114.5)
1-1/4”
(6.4)
1/8”
(3.2)
NOM.
2-9/32”
(57.9)
2
1-3/4”
(44.5)
1
2-3/4”
(69.9)
2-3/4"(69.9) ALLOWS FOR
TRACK CHASE ONLY. JOB
DESIGN MUST ALLOW FOR
CLEARANCE BETWEEN
CLOSURE DOOR AND MOVING
PANELS.
3-3/4”
(95.3)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
NOT BY KAWNEER. PANEL
DESIGN MUST CONSIDER
RELATIVE LOCATION OF
PANEL STACK
SHIM AS REQUIRED TO
PLUM RECEIVING JAMB
1-29/32”
(40.4)
1-3/4”
(44.5)
1-29/32”
(40.4)
2-1/4”
(57.2)
2-1/4”
(57.2)
MEETING STILES FOR 90°
TWO WAY STACK
2-9/32"
(57.9)
2-9/32"
(57.9)
8
2-9/32”
(57.9)
1-9/16”
(39.7)
TRACK
C
L
7
4-1/2”
(114.5)
1/8”
NOM.
MEETING STILES
RECEIVING JAMB
ASSEMBLY
W/ SIDELIGHT
NOTE: CYLINDER LOCKS SHOWN
FOR ILLUSTRATION ON LY
(SPECIFY EXACT LOCATION.)
kawneer.com
9
2-3/4”
(69.9)
4-1/32”
(102.4)
TERMINATOR
STILE
4-1/2”
(114.5)
6
© Kawneer Company, Inc., 2009
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
3
10
1040 SLIDING MALL FRONT
4
APRIL, 2009
EGRESS DOOR
EC 97911-10
SCALE 3" = 1'-0"
NOTE: REFER TO PAGES 10 AND 11 FOR STANDARD
1040 SLIDING MALL FRONT DETAILS.
1
8
10
12
12
8
11
5
ELEVATIONS ARE NUMBERED KEYED BELOW AND ON PAGE 5.
6
SURFACE HEAD TRACK
APPLICATION
HEAD TRACK
5/8”
(15.9)
OPTIONAL
1/16”
(1.6)
2-9/32”
(57.9)
PANEL
TOP
RAIL
STANDARD
CLEARANCE
2-9/32”
(57.9)
1/16" (1.6)
2-9/32”
2-9/32”
(57.9)
(57.9)
2
TRANSOM RAIL
@SIDELIGHT
2-9/32”
(57.9)
DOOR
TOP
RAIL
DOOR OPENING
1-3/4”
(44.5)
NOTE: TO COMPLY WITH 1/2" MAX.
THRESHOLD HEIGHT AT EGRESS
DOOR, TOP SURFACE OF FLOOR
TRACK MUST BE FLUSH WITH
FINISHED FLOOR.
5
3
41-5/32”
(113.5)
FINISH FLOOR
PANEL
BOTTOM
RAIL
1/8”
(3.2)
SURFACE
TRACK
1-1/2”
(38.1)
MIN.
CHASE
DEPTH
4 -15/32"
(113.5)
DOOR
BOTTOM
RAIL
1/8"
(3.2)
5/8"
(15.9)
DOOR
TOP
RAIL
4
TRANSOM RAIL
1-3/4”
(44.5)
RAMP
ADAPTER
PANEL
TOP
RAIL
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2-9/32"
(57.9)
OPTIONAL
1-3/4”
(44.5)
STANDARD
CLEARANCE
5/8”
(15.9)
5/8"
(15.9)
HEAD TRACK
5/8"
(15.9)
1-3/4"
(44.5)
1/4"
(6.4)
1/4”
(6.4)
1
SURFACE HEAD TRACK
APPLICATION
RECESSED
TRACK
1-5/16"
(33.3)
1-7/8"
(47.6)
SILL TRACK
91-283
COMPRESSIBLE
SHIM
5 1/2” MIN. CHASE WIDTH
(139.7)
TRACK
SUPPORT
kawneer.com
© Kawneer Company, Inc., 2009
3
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
9
10
6
9
4
2
7
1040® SLIDING MALL FRONT
APRIL, 2009
EC 97911-10
EGRESS DOOR
SCALE 3" = 1'-0"
ELEVATIONS ARE NUMBER KEYED TO DETAILS
DOOR OPENING
DOOR
2-9/32”
(57.9)
1-3/4”
(44.5)
1-3/4”
(44.5)
TERMINATOR STILE
HINGE STILE
PANEL STILE
DOOR OPENING
10
PANEL STILE
11
DOOR
HINGE STILE
4-23/32”
(119.9)
DOOR
4-23/32”
(119.9)
1-3/4”
(44.5)
1-3/4”
(44.5)
4-23/32”
(119.9)
DOOR
LOCK STILE
4-11/16”
(137.8)
12
LOCK STILE
PANEL STILE
1-3/4”
(44.5)
9
PANEL STILE
DOOR
LOCK STILE
PANEL STILE
EGRESS DOOR LIMITATIONS/ HARDWARE
1. Maximum door opening width: (Per Uniform Building
Code) 36"(914.4) - (32" (812.8) clear at 90 degrees).
10. Optional Hardware:
A. Thumbturn inside in lieu of cylinder.
2. Maximum door opening width: 42" (1066.8) (requires
sidelight and/or transom for stability).
B. Adams Rite 4510 latchlock with 4656 handle in lieu
of A.R.M.S.1850 A.
3. Minimum door opening height: (Per Uniform Building
Code) 80" (2032).
C. Adams Rite 4089 exit indicator.
D. Cylinder guard.
4. Maximum door opening height: 90" (2286)
E. Flush pull in door.
© Kawneer Company, Inc., 2009
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
8
6-15/32”
(164.3)
1-3/4”
(44.5)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
7
5. Maximum threshold height: (Per uniform Building Code)
1/2" (12.7).
6. Door cannot be hinged off of sidelight.
7. Minimum light opening width of sidelight: 6 1/4" (158.8).
Note: When using optional hardware, due to its greater
projection, the placement of the exit panel in the stack
is critical to prevent interference with adjacent panels.
11. Not available:
A. Closers.
8. Maximum light opening width of sidelight: 18" (457.2).
B. Panic Decives.
9. Standard Hardware: Reference Page 16 for hardware information).
A. Walking beam top pivot with modified center bottom
pivot.
C. Push-pull Hardware.
D. Pairs of doors or double sidelighted units.
12. Door is not intended for use by general public.
B. Adams Rite M.S. 1850 A lock with two (2) cyclinders.
13. Door is to be locked closed before moving panel.
kawneer.com
5
1040 SLIDING MALL FRONT
6
APRIL, 2009
EC 97911-10
STACK AREA LAYOUT
PARALLEL STAGGERED STACK
2'-6"/3'-0"
(762/914)
WxD
3'-0"/3'6"
(914/1067)
WxD
3'-6"/4'-0"
(1067/1219)
WxD
4'-0"/4'-6"
(1219/1372)
WxD
4'-6"/5'-0"
(1372/1524)
WxD
5'-0"/5'6"
(1524/1676)
WxD
5'-6"/6'-0"
(1676/1829)
WxD
6'-0"/6'-6"
(1829/1981)
WxD
6'-6"/7'-0"
(1981x2134)
WxD
3
51-9/16" x 14"
(1310 x 356)
57-9/16" x 14"
(1462 x 356)
63-9/16" x 14"
(1615 x 356)
69-9/16" x 14"
(1761 x 356)
75-9/16" x 14"
(1919 x 356)
81-9/16" x 14"
(2072 x 356)
87-9/16" x 14"
(2224 x 356)
93-9/16" x 14"
(2377 x 356)
99-9/16" x 14"
(2526 x 356)
4
52-1/2" x 16"
(1334 x 406)
58-1/2" x 16"
(1486 x 406)
64-1/2" x 16"
(1638 x 406)
70-1/2" x 16"
(1791 x 406)
76-1/2" x 16"
(1943 x 406)
82-1/2" x 16"
(2096 x 406)
88-1/2" x 16"
(2248 x 406)
94-1/2" x 16"
(2400 x 406)
100-1/2" x 16"
(2553 x 406)
5
53-7/16" x 18"
(1357 x 457)
59-7/16" x 18"
(1510 x 457)
65-7/16" x 18"
(1662 x 457)
71-7/16" x 18"
(1815 X 457)
77-7/16" x 18"
(1967 x 457)
83-7/16" x 18"
(2119 x 457)
89-7/16" x 18"
(2272 x 457)
95-7/16" x 18" 101-7/16" x 18"
(2577 x 457)
(2424 x 457)
6
54-3/8" x 20
(1381 x 508)
60-3/8" x 20"
(1534 x 508)
66-3/8" x 20"
(1686 x 508)
72-3/8" x 20"
(1838 x 508)
78-3/8" x 20"
(1991 x 508)
84-3/8" x 20"
(2143 x 508
90-3/8" x 20"
(2296 x 508)
96-3/8" x 20"
(2448 x 508
7
55-5/16" x 22"
(1450 x 559)
61-5/16" x 22"
(1557 x 559)
67-5/16" x 22"
(1710 x 559)
73-5/16" x 22"
(1862 x 559)
79-5/16" x 22"
2015 x 559)
85-5/16" x 22"
(2167 x 559)
91-5/16" x 22"
(2319 x 559)
97-5/16" x 22" 103-5/16" x 22"
(2624 x 559)
(2472 x 559)
8
56-1/4"x 24"
(1429 x 610)
62-1/4" x 24"
(1581 x 610)
68-1/4" x 24"
(1734 x 610)
74-1/4" x 24"
(1886 x 610)
80-1/4" x 24"
(2038 x 610)
86-1/4" x 24"
(2191 x 610)
92-1/4" x 24"
(2343 x 610)
98-1/4" x 24"
(2496 x 610)
9
57-3/16" x 26"
(1453 x 660)
63-3/16" x 26"
(1605 x 660)
69-3/16" x 26"
(1757 x 660)
75-3/16" x 26"
(1910 x 660)
81-3/16" x 26"
(2062 x 660)
87-3/16" x 26"
(2215 x 660)
93-3/16" x 26"
(2367 x 660)
99-3/16" x 26" 105-3/16" x 26"
(2672 x 660)
(2519 x 660)
10
58-1/8" x 28"
(1476 x 711)
64-1/8" x 28"
(1629 x 711)
70-1/8" x 28"
(1781 x 711)
76-1/8" x 28"
(1934 x 711)
82-1/8" x 28"
(2086 x 711)
88-1/8" x 28"
(22381 x 711)
94-1/8" x 28"
(2391 x 711)
100-1/8" x 28"
(2543 x 711)
102-3/8" x 20"
(2600 x 508)
104-1/4" x 24"
(2648 x 610)
CLOSET WALL
REFER TO LAYOUT CHART
ABOVE FOR "W" AND "D"
DIMENSIONS.
2-3/4”
(69.9)
STANDARD
TRACK
C
L
W
5-1/2”
(139.7)
MINIMUM
D
CLEAR OPENING
NOTE: 1. CHASE AREA MUST BE A MINIMUM OF 1-1/2" (38.1) DEEP.
2. STACK AREA MUST BE ACCESSIBLE FOR MAINTENANCE AND CLEANING.
kawneer.com
© Kawneer Company, Inc., 2009
106-1/8" x 28"
(2596 x 711)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
NO. OF
PANELS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
PANEL WIDTH
1040® SLIDING MALL FRONT
APRIL, 2009
EC 97911-10
7
STACK AREA LAYOUT
PARALLEL EVEN STACK
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
PANEL WIDTH*
NO. OF
PANELS
2'-6" / 3'-0"
(762 / 914)
WxD
3'-0" / 3'6"
(914 / 1067)
WxD
3'-6" / 4'-0"
(1067 / 1219)
WxD
4'-0" / 4'-6"
(1219 / 1372)
WxD
4'-6" / 5'-0"
(1372 / 1524)
WxD
5'-0" / 5'6"
(1524 / 1676)
WxD
5'-6" / 6'-0"
(1676 / 1829)
WxD
6'-0" / 6'-6"
6'-6" / 7'-0"
(1829 / 1981) (1981 x 2134)
WxD
WxD
46" x 14"
(1186 x 356)
50-11/16" x 14"
(1287 x 356)
55-1/4" x 14"
(1403 x 356)
61-1/4" x 14"
(1556 x 356)
67-1/4" x 14"
(1708 x 356)
73-1/4" x 14"
(1861 x 356)
79-1/4" x 14"
(2013 x 356)
85-1/4" x 14"
(2165 x 356)
91-1/4 x 14"
(2318 x 356)
4
55-5/8" x 16"
(1413 x 406)
61-1/4" x 16"
(1556 x 406)
67-1/4" x 16"
(1708 x 406)
73-1/4" x 16"
(1861 x 406)
79-1/4" x 16"
(2013 x 406)
85-1/4" x 16"
(2165 x 406)
91-1/4" x 16"
(2318 x 406)
5
56-9/16" x 18"
(1437 x 457)
61-1/4" x 18"
(1556 x 457)
67-1/4" x 18"
(1708 x 457)
73-1/4" x 18"
(1861 x 457)
79-1/4" x 18"
(2013 x 508)
85-1/4" x 18"
(2165 x 457)
91-1/4" x 18"
(2318 x 457)
6
61-1/2" x 20"
(1562 x 508)
67-1/4" x 20"
(1708 x 508)
73-1/4" x 20"
(1861 x 508)
79-1/4" x 20"
(2013 x 508)
85-1/4" x 20"
(2165 x 508)
91-1/4" x 20"
(2318 x 508
7
62-7/16" x 22"
(1586x559)
67-1/4" x 22"
(1708 x 559)
73-1/4" x 22"
(1861 x 559)
79-1/4" x 22"
(2013 x 559)
85-1/4" x 22"
(2165 x 559)
91-1/4" x 22"
(2318 x 559)
8
67-3/8" x 24"
(1711 x 610)
73-1/4" x 24"
(1861 x 610)
79-1/4" x 24"
(2013 x 610)
85-1/4" x 24"
(2165 x 610)
91-1/4" x 24"
(2318 x 610)
9
68-5/16" x 26"
(1735 x 660)
73-1/4" x 26"
(1861 x 660)
79-1/4" x 26"
(2013 x 660)
85-1/4" x 26"
(2165 x 660)
91-1/4" x 26"
(2318 x 660)
73-1/4" x 28"
(1861 x 711)
79-1/4" x 28"
(2013 x 711)
85-1/4" x 28"
(2165 x 711)
91-1/4" x 28"
(2318 x 711)
3
10
CLOSET WALL
REFER TO LAYOUT CHART
ABOVE FOR "W" AND "D"
DIMENSIONS.
CASTER SPACING
2-3/4”
(69.9)
STANDARD
TRACK
C
L
W
NOTE: 1. CHASE AREA MUST BE A MINIMUM OF 1-1/2" (38.1) DEEP.
2. STACK AREA MUST BE ACCESSIBLE FOR MAINTENANCE AND CLEANING.
3. MAXIMUM NUMBER OF PANELS FOR THIS STACK AREA DEPENDS UPON PANEL WIDTHS.
CONTACT FACTORY REPRESENTATIVE.
4. EDGE PULLS REQUIRED ON LAST TWO PANELS INTO STACK AREA.
kawneer.com
5-1/2”
(139.7)
MINIMUM
D
© Kawneer Company, Inc., 2009
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
*THE CASTER SPACING DIMENSION SHOWN BELOW SHOULD BE AT LEAST 1/3 OF THE PANEL HEIGHT.
THE CASTER VARIES FROM A PANEL EDGE BY 8-5/6" FOR 3 PANELS AS SHOWN PLUS ABOUT 1" FOR
EACH ADDITIONAL PANEL.
CLEAR OPENING
1040 SLIDING MALL FRONT
8
APRIL, 2009
EC 97911-10
STACK AREA LAYOUT
90° STACK
3'-6"/4'-0"
(1067 / 1219)
WxD
4'-0"/4'-6"
(1219 / 1372)
WxD
4'-6"/5'-0"
(1372 / 1524)
WxD
5'-0"/5'6"
(1524 / 1676)
WxD
5'-6"/6'-0"
(1676 / 1829)
WxD
6'-0"/6'-6"
(1829 / 1981)
WxD
6'-6"/7'-0"
(1981 x 2134)
WxD
23-3/8" x 47-3/4"
(594 x 1213)
23-3/8" x 53-3/4"
(594 x 1365)
23-3/8" x 59-3/4"
(594 x 1518)
23-3/8" x 65-3/4"
(594 x 1670)
23-3/8" x 71-3/4"
(594 x 1822)
23-3/8" x 77-3/4"
(594 x 1975)
23-3/8" x 83-3/4"
(594 x 2127)
23-3/8" x 89-3/4"
(594 x 2280)
23-3/8" x 95-3/4"
(594 x 2432)
25-3/8" x 48-11/16" 25-3/8" x 54-11/16" 25-3/8" x 60-11/16" 25-3/8" x 66-11/16" 25-3/8" x 72-11/16" 25-3/8" x 78-11/16" 25-3/8" x 84-11/16" 25-3/8" x 90-11/16" 25-3/8" x 96-11/16"
(645 x 2304)
(645 x 1237)
(645x 1389)
(645 x 1541)
(645 x 1694)
(645 x 1846)
(645 x 1999)
(645 x 2151)
(645 x 2456)
5
27-3/8" x 49-5/8"
(695 x 1260)
27-3/8"x55-5/8"
(695x1413)
27-3/8" x 61-5/8"
(695 x 1565)
6
29-3/8" x 50-9/16"
(746 x 1284)
29-3/8"x56-9/16"
(746x1437)
7
31-3/8" x 51-1/2"
(797 x 1308)
8
9
27-3/8" x 97-5/8"
(695 x 2480)
29-3/8" x 62-9/16" 29-3/8" x 68-9/16" 29-3/8" x 74-9/16"
(746 x 1589)
(746 x 1741)
(746 x 1894)
29-3/8" x 80-9/16" 29-3/8" x 86-9/16" 29-3/8" x 92-9/16"
(746 x 2351)
(746 x 2046)
(746 x 2199)
29-3/8" x 98-5/16"
(746 x 2503)
31-3/8"X57-1/2"
(797X1461)
31-3/8" x 63-1/2"
(797 x 1613)
31-3/8" x 69-1/2"
(797 x 1765)
31-3/8" x 75-1/2"
(797 x 1918)
31-3/8" x 81-1/2"
(797 x 2070)
31-3/8" x 93-1/2"
(797 x 2375)
31-3/8" x 99-1/2"
(797 x 2527)
33-3/8" x 52-7/16"
(848 x 1332)
33-3/8"x58-7/16"
(848x1484)
33-3/8" x 64-7/16" 33-3/8" x 70-7/16"
(848 x 1637)
(848 x 1789)
33-3/8 x 76-7/16"
(848 x 1942)
33-3/8" x 82-7/16" 33-3/8" x 88-7/16" 33-3/8" x 94-7/16" 33-3/8" x 100-7/16"
(848 x 2399)
(848 x 2094)
(848 x 2246)
(848 x 2551)
35-3/8" x 53-3/8"
(899 x 1356)
35-3/8"x59-3/8"
(899x1508)
35-3/8" x 65-3/8"
(889 x 1661)
35-3/8" x 77-3/8"
(899 x 1965)
35-3/8" x 83-3/8"
(899 x 2118)
37-3/8" x 54-3/8"
(949 x 1380)
37-3/8"x60-5/16"
(949x1532)
37-3/8" x 66-5/16" 37-3/8" x 72-5/16" 37-3/8" x 78-5/16"
(949 x 1684)
(949 x 1989)
(949 x 1837)
35-3/8" x 71-3/8"
(899 x 1813)
27-3/8" x 73-5/8"
(695 x 1870)
27-3/8" x 79-5/8"
(695 x 2022)
27-3/8" x 85-5/8"
(695 x 2175)
31-3/8" x 87-1/2"
(797 x 2223)
35-3/8" x 89-3/8"
(899 x 2270)
35-3/8" x 95-3/8"
(899x 2423)
35-3/8" x 101-3/8"
(899 x 2579)
37-3/8" x 84-5/16" 37-3/8" x 90-5/16" 37-3/8" x 96-5/16" 37-3/8" x 102-5/16"
(949 x 2246)
(949 x 2142)
(949 x 2294)
(949 x 2599)
TRACK CLEARANCE (DIM. C.)
MIN. STACK OPENING 1'6" (304.8)
10
27-3/8" x 91-5/8"
(695 x 2327)
27-3/8" x 67-5/8"
(695 x 1718)
PANEL WIDTH IN FEET
8
DIM “C”
D
12”
6”
48”
24”
36”
18”
(1219.2) (914.4) (609.2) (457.2) (304.8) (152.4)
7
2
6
5
1.5
4
1
3
2
.5
1
10”
(254)
30”
(762)
50”
(1270)
70”
(1778)
STACK OPENING (DIM. E.)
W
5-1/2”
(139.7)
MINIMUM
TRACK
C
L
DIM “E”
MIN. STACK OPENING 6" (152.4)
1-3/4”
(44.5)
STANDARD
EXAMPLE:
A 5' PANEL WIDTH WITH AN 18"
TRACK CLEARANCE (DIM. C)
WOULD REQUIRE A 30" STACK
OPENING (DIM. "E.)
CLEAR OPENING
NOTE: 1. CHASE AREA MUST BE A MINIMUM OF 1-1/2" (38.1) DEEP.
2. STACK AREA MUST BE ACCESSIBLE FOR MAINTENANCE AND CLEANING.
kawneer.com
© Kawneer Company, Inc., 2009
4
3'-0"/3'6"
(914 / 1067)
WxD
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
3
2'-6"/3'-0"
(762 / 914)
WxD
PANEL WIDTH IN METERS
NO. OF
PANELS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
PANEL WIDTH
1040® SLIDING MALL FRONT
APRIL, 2009
EC 97911-10
9
SIZE LIMITATIONS/GENERAL INFORMATION
Mullions are designed for 1/80 deflection ratio. These curve are for mullions WITH and WITHOUT HORIZONTALS and are based on precise
engineering calculations for stress, deflection and buckling. Allowable windload stress for Aluminum 12,929 P.S.I. (89 MPa) STEEL 26,666 P.S.I,
(194 MPa). Charted curves in all cases are for the limiting value. For special situations not covered by the curves, contact your Kawneer
representative for additional information.
EXTERIOR APPLICATION
DEFLECTIONS L/80
INTERIOR APPLICATION
(WINDLOAD NOT APPLICABLE)
WIDTH IN METERS
WIDTH IN METERS
1.0
1.5
2.0
3.5
11
10
3
2
6
5
1.5
4
1
3
2
.5
I=.896 (37.3 x 104)
S=1.024(16.8 x 103)
1
0
1
2
3
4
5
HEIGHT IN METERS
HEIGHT IN FEET
2.5
7
6
7
8
2.0
10
3
9
2.5
8
7
2
6
5
1.5
4
1
3
2
.5
I=.896 (37.3 x 104)
S=1.024(16.8 x 103)
0
1
2
3
4
5
6
7
8
WIDTH IN FEET
NOTE: 1. PANEL WIDTHS (CATER SPACING) SHOULD BE AT LEAST 1/3 OF PANEL HEIGHT FOR
ROLLING STABILITY THE MAJOR EXCEPTION TO THIS RULE IS THE PARALLEL EVEN
STACK LAYOUT (SEE ASTERISK ON PAGE 13 OF SECTION B1)
2. ON PANELS OVER 10' IN HEIGHT AN INTERMEDIATE HORIZONTAL MOUNTING IS
RECOMMENDED.
GENERAL INFORMATION
GENERAL DESCRIPTION: THE "1040" SLIDING FRONT CONSISTS OF SINGLE TRACKAGE WITH
MULTIPLE STACKING OPTIONS FOR INTERIOR OR EXTERIOR APPLICATIONS. IT IS IDEALLY
SUITED FOR THE FOLLOWING COMMERCIAL APPLICATIONS:
© Kawneer Company, Inc., 2009
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
1.5
3.5
1
WIDTH IN FEET
1.0
11
A = 15 PSF (720 PA)
B = 20 PSF (960 Pa)
C = 25 PSF (1200 Pa)
9
8
.5
12
HEIGHT IN METERS
.5
12
HEIGHT IN FEET
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MAXIMUM PANEL SIZE LIMITATIONS
•
•
•
•
•
•
kawneer.com
ENCLOSED SHOPPING MALLS
EXTERIOR MOVEABLE WALLS
AUTOMOBILE SHOWROOMS
SLIDING ROOM DIVIDERS
EDUCATIONAL MOVEABLE PARTITIONS
INSTITUTIONAL SLIDING DOORS
EDGE PULL
INBOARD
CASTER
OUTBOARD
RECESSED
CASTER
FACE PULL
(OPTIONAL)
INBOARD
HEAD
GUIDE
MS 1850A
LOCK
OUTBOARD
RECESSED
HEAD GUIDE
REFER TO HARDWARE SECTION FOR INFORMATION
ON ADAMS RITE 4510 LATCHLOCK, 4560 LEVER HANDLE AND
4089 EXIT INDICATOR USED OPTIONALLY ON THE EGRESS DOOR.
kawneer.com
© Kawneer Company, Inc., 2009
HARDWARE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1040 SLIDING MALL FRONT
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
10
APRIL, 2009
EC 97911-10
1040 HARDWARE