Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2000T Terrace Doors EC 97911-065 FEATURES 1 Features • Performance class and grade: Single: AW-PG90-ATD Pairs: AW-PG65-ATD • Outswing or inswing • Door is 2-1/4" (57.2) deep • 1" x 4" (25.4 x 101.6) door frame • Mitered door and frame corners • Polyamide thermal break • Infill options up to 1-1/16" (27) • Three way adjustable butt hinges • Stainless steel multipoint latch lock / deadbolt with swinghooks and shootbolts as required • Solid brass lever handle selection in multiple finishes • Concealed stainless steel door stop • Assembled and shipped with door hung in frame • PermanodicTM anodized finishes in seven choices • Painted finishes in standard and custom choices Optional Features • Two-color finish capability • LCN 1260 surface applied closer • Low profile threshold (Outswing Single) • 2000T Terrace Door has been small and large missile impact and cycle tested © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. AUGUST, 2015 Product Applications • The 2000T Terrace Door is a high performance balcony door for use in condominiums, lofts, hotels and apartments • The 2000T Terrace Door Frame is intended to be installed in "punched" openings or as a liner frame within other Kawneer framing or curtain wall systems • When sidelites and/or transoms are required the 2000T door frame is installed as a liner frame within other Kawneer framing or curtain wall systems For specific product applications, Consult your Kawneer representative. kawneer.com ADMA080 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2000T Terrace Doors AUGUST, 2015 BLANK PAGE EC 97911-065 ADMA080 kawneer.com © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2 2000T Terrace Doors EC 97911-065 INDEX 3 OUTSWING DOOR DETAILS.............................................................. 5 INSWING DOOR DETAILS.................................................................. 6 SIDELITES AND TRANSOM............................................................... 7 STANDARD GLAZING OPTIONS....................................................... 8 HARDWARE...................................................................................9, 10 STRUCTURAL LIMITATIONS............................................................ 11 THERMAL CHARTS..................................................................... 12-15 LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AUGUST, 2015 The following metric (SI ) units are found in these details: m –meter cm – centimeter mm –millimeter s –second Pa –pascal MPa –megapascal Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement. kawneer.com ADMA080 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2000T Terrace Doors AUGUST, 2015 BLANK PAGE EC 97911-065 ADMA080 kawneer.com © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 4 AUGUST, 2015 2000T Terrace Doors EC 97911-065 OUTSWING DOOR DETAILS 1 Single Door Maximun Frame Size = 48" x 96" (1219.2 x 2438.4) Minimum Frame Size = 30" x 73" (762 x 1854.2) 1 3 4 3 opp. 3 5 2 2A Pair of Doors Maximun Frame Size = 96" x 96" (2438.4 x 2438.4) Minimum Frame Size = 60" x 81" (1524 x 2057.4) 2 OUTSWING DOORS & FRAME 1" (25.4) 1-25/32" (45.2) 3/16" (4.8) 4-13/32" (111.9) 5-1/8" (130.2) 3/8" (9.5) 17/32" (13.5) 4" (101.6) 1-25/32" (45.2) 1" (25.4) 1-25/32" (45.2) 1" (25.4) 1" (25.4) 1-25/32" (45.2) 3/16" (4.8) 4-13/32" (111.9) 5-1/8" (130.2) 3/16" (4.8) 17/32" (13.5) 3/8" (9.5) 4-13/32" (111.9) DLO DLO FRAME WIDTH 3/16" (4.8) 17/32" (13.5) 3/8" (9.5) 4-13/32" (111.9) FRAME WIDTH 4 LOCK JAMB AT DEADBOLT/LATCHLOCK 3 PIVOT JAMB 1/2" (12.7) 4-13/32" (111.9) 3/16" (4.8) DLO 1/8" (3.2) 1/4" (6.4) FRAME HEIGHT 4-25/32" (121.4) DLO 3/8" (9.5) 17/32" (13.5) FRAME HEIGHT 2 SILL © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. DLO DLO 1 HEAD FRAME HEIGHT Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. SCALE 3" = 1' 0" 5 4-13/32" (111.9) 9" (228.6) 2A LOW PROFILE SILL (Available on single door only) kawneer.com 4-13/32" (111.9) 5 MEETING STILE ADMA080 DLO 2000T Terrace Doors AUGUST, 2015 INSWING DOOR DETAILS EC 97911-065 SCALE 3" = 1' 0" 1 Single Door Maximun Frame Size = 48" x 96" (1219.2 x 2438.4) Minimum Frame Size = 30" x 73" (762 x 1854.2) 1 3 4 3 3 opp. 5 Pair of Doors Maximun Frame Size = 96" x 96" (2438.4 x 2438.4) Minimum Frame Size = 60" x 81" (1524 x 2057.4) 2 2 INSWING DOORS & FRAME 3-25/32" (96.0) 3-11/32" (84.9) 5-1/8" (130.2) 17/32" (13.5) 3/16" (4.8) 4-13/32" (111.9) 17/32" (13.5) 3/16" (4.8) 3-25/32" (111.9) 3/8" (9.5) DLO DLO FRAME WIDTH 3/16" (4.8) 17/32" (13.5) 3/8" (9.5) 4 LOCK JAMB AT DEADBOLT/LATCHLOCK DLO 9" (228.6) 4-13/32" (111.9) 5-1/8" (130.2) FRAME WIDTH 3 PIVOT JAMB DLO 1" (25.4) 4-13/32" (111.9) 3/16" (4.8) 5 MEETING STILE ADMA080 kawneer.com © Kawneer Company, Inc., 2015 5-1/8" (130.2) 3-11/32" (84.9) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 4-13/32" (111.9) 3-11/32" (84.9) 3-11/32" (84.9) 1" (25.4) 1" (25.4) 5-1/8" (130.2) 3/8" (9.5) 2 SILL FRAME HEIGHT DLO DLO 1 HEAD FRAME HEIGHT 1" (25.4) 3/16" (4.8) 17/32" (13.5) 3/8" (9.5) 4" (101.6) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 6 © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AUGUST, 2015 2000T Terrace Doors EC 97911-065 SIDELITES AND TRANSOM SCALE 3" = 1' 0" 3 2 TRANSOM BAR kawneer.com 4 1 1 2 2 3 ADMA080 4 OUTSWING DOORS & FRAME TRIFAB 451T FRAME SHOWN 1 TRANSOM HEAD 3 SIDELITE JAMB 4 DOOR JAMB 7 1" (25.4) INFILL OUTSWING DOOR ADMA080 2000T Terrace Doors AUGUST, 2015 STANDARD GLAZING OPTIONS EC 97911-065 WEDGE GASKET GASKET 1/4" (6.4) INFILL OUTSWING DOOR 1/4" (6.4) INFILL INSWING DOOR 1" (25.4) WEDGE WEDGE GASKET GASKET 1" (25.4) INFILL INSWING DOOR 1/4" (6.4) and 1" (25.4) infills shown, other infills available. kawneer.com © Kawneer Company, Inc., 2015 1/4" (6.4) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. WEDGE Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. GLASS BITE 5/8" (15.9) GLASS BITE 5/8" (15.9) 1/4" (6.4) GLASS BITE 5/8" (15.9) GLASS BITE 5/8" (15.9) 8 SCALE 3" = 1' 0" 1" (25.4) AUGUST, 2015 2000T Terrace Doors EC 97911-065 HARDWARE 9 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. TRIM SETS Contemporary Rodos style solid brass lever handle and escutcheon plate. Available in three finishes Polished Brass, Brushed Chrome and Rustic Umber. Includes keyed cylinder and thumbturn. LATCHLOCK/DEADBOLT GEARBOX Stainless steel gearbox provides both a latchlock for normal use and deadbolt for additional security. Lock strike plates are stainless steel and adjustable. Each includes an injection molded plastic dust box. Swinghooks provide additional locking points along the vertical edge of the door leaf. Lockstrikes are stainless steel and adjustable. Each includes an injection molded plastic dust box. © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. SWINGHOOK SHOOT BOLT AND SLEEVE Top and bottom stainless steel shoot bolts secure the inactive leaf of pairs to the transom bar and threshold. kawneer.com ADMA080 10 2000T Terrace Doors AUGUST, 2015 HARDWARE EC 97911-065 Trim sets are shipped loose to avoid damage during construction. The construction handle and construction plate allow temporary operation of the locking hardware. ADJUSTABLE BUTT HINGE Aluminum 3-way adjustable hinges improve alignment between door leaf and frame. Hinges adjust in and out, up and down and left to right without removing the door leaf. Available in clear and dark bronze anodized finishes or painted to match door leaf. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. CONSTRUCTION HANDLE AND BACK PLATE DOOR STOP Stainless steel door stop assemblies are concealed in the top rail of the door leaf. ADMA080 kawneer.com © Kawneer Company, Inc., 2015 Door and frame will accommodate LCN 1260 surface mounted closer and drop plate. Note: Closer is mounted on exterior side of frame with inswing door. Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. SURFACE APPLIED CLOSER AUGUST, 2015 2000T Terrace Doors EC 97911-065 STRUCTURAL LIMITATIONS 11 Charted wind load curves are based on allowable stress for aluminum of 15,152 PSI and a L/175 deflection ratio and, in all cases represent the limiting values. Dimensional limits at the stated wind loads are for door frame members anchored at the ends. Wind load charts contained herein are based upon nominal wind load utilized in allowable stress design. To convert ultimate wind loads to nominal loads, multiply ultimate wind loads by a factor of 0.6 per ASCE/SEI 7. SMALL ASTRAGAL A= 20 PSF (960) B= 30 PSF (1440) C= 40 PSF (1920) D= 50 PSF (2400) E= 60 PSF (2880) F = 65 PSF (3120) G= 75 PSF (3600) H= 80 PSF (3840) I = 90 PSF (4320) J = 100 PSF (4800) K= 120 PSF (5760) GLASS CENTERS IN METERS 3.5 11 10 A 9 B 2.5 C D E 2.0 8 7 6 5 4 3.0 1.5 0 1 2 3 4 GLASS HEIGHT IN METERS 1.0 0.5 12 GLASS HEIGHT IN FEET Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. WIND LOAD LIMITATIONS 259209 259210 259209 5 GLASS CENTERS IN FEET MEDIUM ASTRAGAL GLASS CENTERS IN METERS 1.0 GLASS HEIGHT IN FEET 10 3.0 C D 2.5 F G I 2.0 9 8 7 6 5 4 1.5 0 1 2 3 4 259211 259209 259209 5 GLASS CENTERS IN FEET LARGE ASTRAGAL © Kawneer Company, Inc., 2015 GLASS CENTERS IN METERS 1.0 C 3.5 11 E 3.0 H J 2.5 K 10 9 8 7 2.0 6 5 4 1.5 0 1 2 3 4 GLASS HEIGHT IN METERS 0.5 12 GLASS HEIGHT IN FEET Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 3.5 11 GLASS HEIGHT IN METERS 0.5 12 259212 259209 5 GLASS CENTERS IN FEET kawneer.com ADMA080 259209 12 2000T Terrace Doors AUGUST, 2015 THERMAL CHARTS EC 97911-065 Generic Project Specific U-factor Example Calculation (Percent of Glass will vary on specific products depending on sitelines) 30.125" (765.2) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. (DLO) 75.75" (1924.1) (F.H.) 7'-2" (2184.4) (DLO) Note:2000T Terrace Door outswing shown for example. 3'-4" (1016.0) (F.W.) Example Glass U-Factor = 0.28 Btu/hr • ft2 • °F Total Daylight Opening = 30.125" x 75.75" = 15.85 ft2 Total Projected Area = 3'-4" x 7'-2" = 23.9 ft2 Percent of Glass = (Total Daylight Opening ÷ Total Projected Area)100 = (15.85 ÷ 23.9)100 = 66% System U-factor vs Percent of Glass Area 0.90 0.80 (4.50) 0.75 N E IGN PL S M E A D EX OR F T O 0.65 0.60 0.55 0.50 0.49 0.45 (3.50) (3.00) W m2 • °C System U-factor (2.73) (2.61) (2.50) (2.39) (2.27) (2.16) (2.05) (1.93) (1.82) (1.71) (1.59) (1.48) (1.37) (1.25) (1.14) (4.00) Btu hr • ft2 • °F System U-factor COG U-factor (2.50) 0.40 0.35 (2.00) 0.30 0.25 (1.50) 0.20 85 80 75 70 Percent of Glass Area 65 60 66% 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.24 0.22 0.20 0.70 Based on 66% glass and center of glass (COG) U-factor of 0.28 System U-factor is equal to 0.49 Btu/hr • ft2 • °F ADMA080 kawneer.com © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. (5.00) 0.85 AUGUST, 2015 2000T Terrace Doors EC 97911-065 THERMAL CHARTS 13 2000T TERRACE DOOR - SINGLE LEAF Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Btu hr • ft2 • °F System U-factor COG U-factor Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADMA080 System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADMA080 System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC 2000T Terrace Doors AUGUST, 2015 THERMAL CHARTS EC 97911-065 kawneer.com © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 14 2000T TERRACE DOOR - SINGLE LEAF Vision Area / Total Area (%) AUGUST, 2015 2000T Terrace Doors EC 97911-065 THERMAL PERFORMANCE MATRIX (NFRC SIZE) 2000T TERRACE DOOR SINGLE LEAF Thermal Transmittance 1 (BTU/hr • ft 2 • °F) Overall U-Factor 4 0.48 0.58 0.46 0.56 0.44 0.55 0.42 0.54 0.40 0.53 0.38 0.52 0.36 0.50 0.34 0.49 0.32 0.48 0.30 0.47 0.28 0.46 0.26 0.44 0.24 0.43 0.22 0.42 0.20 0.41 NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Glass U-Factor 3 kawneer.com 15 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1000mm wide by 2000mm high (39-3/8" by 78-3/4"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.51 0.75 0.49 0.70 0.47 0.70 0.46 0.65 0.44 0.65 0.42 0.60 0.41 0.60 0.39 0.55 0.38 0.55 0.36 0.50 0.34 0.50 0.33 0.45 0.31 0.45 0.29 0.40 0.28 0.40 0.26 0.35 0.25 0.35 0.23 0.30 0.21 0.30 0.20 0.25 0.18 0.25 0.16 0.20 0.15 0.20 0.13 0.15 0.12 0.15 0.10 0.10 0.08 0.10 0.07 0.05 0.05 0.05 0.03 ADMA080 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2000T Terrace Doors AUGUST, 2015 BLANK PAGE EC 97911-065 ADMA080 kawneer.com © Kawneer Company, Inc., 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 16