NSNJ2007

NSNJ2007 Aug. 2015
New JRC SAW FILTER
NSNJ2007
Application
Low Power Transceiver f0=446.05MHz BW=0.1MHz
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Electrical Specifications
Item
Input and Output Impedance
Nominal Center Frequency (f0)
Insertion Loss
446.0~446.1MHz
Response Variation
446.0~446.1MHz
VSWR
446.0~446.1MHz
Out of Band Rejection
402.60625~402.69375MHz
(Relative to
424.30625~424.39375MHz
Through Level)
435.15625~435.24375MHz
435.45~435.55MHz
456.55~456.65MHz
424.9~425.0MHz
467.1~467.2MHz
Spec.
3.0dB max.
1.0dB max.
2.0 max.
50dB min.
40dB min.
40dB min.
20dB min.
20dB min.
40dB min.
40dB min.
Typ.
50
446.05MHz
2.3dB
0.1dB
1.2
69dB
65dB
61dB
61dB
28dB
59dB
56dB
(Operating Temperature Range: -20~+60ºC)
Maximum Rating: (Table 2)
Table2. Maximum Ratings
Item
Maximum Input Power
Maximum DC Voltage
Operating Temperature Range
Storage Temperature
Rating
+20dBm
7.5V
-20~+60ºC
-30~+85ºC
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.njr.co.jp/products/device/index.html (Japanese)
http://www.njr.com/products/device/index.html (English)
NSNJ2007 Aug 2015
1
IN
50
6
OUT
50
2 SAW 5
3
4
Fig.1 Measuring circuit
(a)
3. 0±0. 15
( b)
3. 0 ± 0. 1 5
581
( c)
RP
(1)
( 0. 6)
( 0. 2 5)
1. 1 5 ± 0. 1 5
( 2)
4
2
5
( 0. 6)
[ 2 x]
3
Marking
(1) Lot Number
(a) Year
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
(c) Manufacture lot
1-9, A-Z, a-z
*I, O, and Q are excluded.
(2) Part Number Mark
( 1. 80)
1
6
[ 4x]
( 0. 5 3)
[ 4 x]
( 0. 75)
( 0. 45)
Pin no.
Fig.2 Package dimensions (in mm)
0.93
3.8
1.15
3.8
0.6
2.2
0.93
1.15
Fig.3 Desirable land area (in mm)
Connection
1
GND
2
IN/OUT
3
GND
4
GND
5
OUT/IN
6
GND
NSNJ2007 Aug 2015
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -20ºC or more than +60ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
NSNJ2007 Aug 2015
S21
0
1
Insertion Loss [dB]
2
3
4
5
6
7
8
9
10
Center 446.05[MHz]
S11
S22
Center 446.05[MHz]
Span 100[MHz]
Center 446.05[MHz]
Span 100[MHz]
S11
S22
6
5
5
VSWR
6
4
3
2
4
3
2
1
Center 446.05[MHz]
Span 20[MHz]
1
Center 446.05[MHz]
Span 20[MHz]
S21
0
10
20
Insertion Loss [dB]
VSWR
Span 20[MHz]
30
40
50
60
70
80
Center 446.05[MHz]
Span 100[MHz]