NSTS9119 Aug. 2015 New JRC SAW FILTER NSTS9119 Application ITS f0=760MHz BW=9MHz High ATT Type Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Input and Output Impedance Nominal Center Frequency (f0) Spec. Insertion Loss 755.5~764.5MHz Response Variation 755.5~764.5MHz VSWR Out of Band Rejection (Relative to Through Level) 755.5~764.5MHz 750MHz 770MHz 4.3dB max. 5.0dB max. 2.0dB max. 2.5dB max. 2.5 max. 20dB min. 10dB min. Typical 50 760MHz 3.3dB 4.5dB 0.8dB 2.0dB 2.0 27dB 15dB 12dB min. 5dB min. 17dB 8dB Temp. 25±5ºC -40~+85ºC 25±5ºC -40~+85ºC -40~+85ºC 25±5ºC -40~+85ºC 25±5ºC -40~+85ºC (Operating Temperature Range : -40~+85ºC) Maximum Rating: (Table 2) Table2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +20dBm 7.5V -40~+85ºC -40~+95ºC Mechanical Specifications: (Fig.2) Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling. http://www.njr.co.jp/products/device/index.html （Japanese） http://www.njr.com/products/device/index.html （English） NSTS9119 Aug. 2015 1 6 2 SAW 5 3 IN 50 4 OUT 50 Fig.1 Measuring circuit (a) 3. 0±0. 15 ( b) 3. 0 ± 0. 1 5 581 ( c) IH (1) ( 0. 6) ( 0. 2 5) 1. 1 5 ± 0. 1 5 ( 2) 4 2 5 ( 0. 6) [ 2 x] 3 Marking (1) Lot Number (a) Year (b) Month *Oct.--- X Nov.--- Y Dec.--- Z (c) Manufacture Lot 1-9, A-Z, a-z *I, O, and Q are excluded. (2) Part Number Mark ( 1. 80) 1 ( 0. 75) ( 0. 45) [ 4x] ( 0. 5 3) [ 4 x] 6 Fig.2 Package dimensions (in mm) 0.93 3.8 1.15 3.8 0.6 2.2 0.93 1.15 Fig.3 Desirable land area (in mm) Pin no. Connection 1 GND 2 IN/OUT 3 GND 4 GND 5 OUT/IN 6 GND NSTS9119 Aug. 2015 Notice 1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -40ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influences for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. 2. The information contained herein may be changed without prior notice. It is therefore advisable to contact New Japan Radio Company before proceeding with the design of equipment incorporating this product. 3. The products are designed to be used with ordinary electronic equipment (data and communications equipment, office equipment, audio-video equipment, measuring instruments, etc). New Japan Radio Company does not assume any liability for the case using the products with the application required high reliability or safety extremely (such as space equipment, sea-bottom equipment, medical equipment etc). When intending to use any our product please contact our sales representatives in advance. NSTS9119 Aug. 2015 S21 0 1 5 2 10 3 15 Insertion Loss [dB] Insertion Loss [dB] S21 0 4 5 6 7 20 25 30 35 8 40 9 45 10 Center 760[MHz] 50 Span 50[MHz] S11 Center 760[MHz] S22 Center 760[MHz] Span 200[MHz] Center 760[MHz] Span 200[MHz] S22 5 5 VSWR 6 4 4 3 3 2 2 Center 760[MHz] Span 50[MHz] 1 Center 760[MHz] Span 50[MHz] S21 0 10 20 Insertion Loss [dB] VSWR S11 6 1 Span 50[MHz] 30 40 50 60 70 80 Start 0[MHz] Stop 3000[MHz]