NSTS9120-E Apr. 2013 NewJRC SAW FILTER NSTS9120 Application ITS 760MHz Low Loss Type Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Item Input and Output Impedance Nominal Center Frequency (f0) Insertion Loss 755.5~764.5MHz Out of Band Rejection (Relative to Through Level) 750MHz 770MHz Spec. 2.5dB max. 4.0dB max. 13dB min. 7dB min. Typical 50Ω 760MHz 2.0dB 2.5dB 17dB 10dB 6dB min. 3dB min. 9dB 5dB Temp. 25±5ºC -40~+85ºC 25±5ºC -40~+85ºC 25±5ºC -40~+85ºC (Operating Temperature Range : -40~+85ºC) Maximum Rating: (Table 2) Table2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +20dBm 7.5V -40~+85ºC -40~+95ºC Mechanical Specifications: (Fig.2) Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling. http://www.njr.co.jp/products/device/index.html http://www.njr.com/products/device/index.html (Japanese) (English) NSTS9120-E Apr. 2013 1 6 2 SAW 5 IN 50Ω 3 4 OUT 50Ω Fig.1 Measuring circuit (a) 3. 0±0. 15 ( b) 3. 0 ± 0. 1 5 162 ( c) IL (1) ( 0. 6) ( 0. 2 5) 1. 1 5 ± 0. 1 5 ( 2) 4 ( 0. 6) [ 2 x] 3 2 5 ( 1. 80) 1 ( 0. 75) ( 0. 45) [ 4x] ( 0. 5 3) [ 4 x] 6 Fig.2 Package dimensions (in mm) 0.93 3.8 1.15 3.8 0.6 2.2 0.93 1.15 Fig.3 Desirable land area (in mm) Marking (1) Lot Number (a) Year (b) Month *Oct.--Nov.--Dec.--(c) Date 1-9--10-19--20-31--(2) Part Number Mark Pin no. 1 2 3 4 5 6 Connection GND IN/OUT GND GND OUT/IN GND X Y Z 0 1 2 NSTS9120-E Apr. 2013 Notice 1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -30ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. Others 1. About RoHS , REACH and Pb-free reflow This product is compliant to RoHS and REACH directive and Pb-free reflow-profile. NSTS9120-E Apr. 2013 Insertion Loss 0 Smith Chart 1 : 755.5 [MHz] 1.9119 [dB] S11 1 2 2 : 764.5 [MHz] 1.6329 [dB] 2 4 1 2 6 8 [dB] 10 735 760 Frequency[MHz] 785 Return Loss S22 12 [5dB/div] 1 1 2 Center Freq. 760 [MHz] Freq.Span 50 [MHz] 2 New Japan Radio Co.,Ltd Insertion Loss 0 Reference 0 [dB] 1 : 750 [MHz] 23.1831 [dB] 10 2 : 770 [MHz] 9.1443 [dB] 2 Division 5 [dB] 20 1 30 40 [dB] 50 660 760 860 Frequency[MHz] New Japan Radio Co.,Ltd