NSTS1449

NSTS1449 Apr. 2013
NewJRC SAW FILTER
NSTS1449
Application
924MHz
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Item
Spec.
Typ.
Input and Output Impedance
50Ω
Nominal Center Frequency (f0)
924MHz
Insertion Loss
3.5dB max.
2.7dB
920~928MHz
Response Variation
1.5dB max.
1.0dB
Input and Output VSWR
2.5 max.
1.8
Out of Band Rejection
DC~710MHz
40dB min.
50dB
(Relative to
710~900MHz
35dB min.
44dB
Through Level)
900~915MHz
8dB min.
23dB
945~1000MHz
25dB min.
35dB
1000~1215MHz
38dB min.
44dB
1848MHz (2*f0)
35dB min.
50dB
2772MHz (3*f0)
20dB min.
37dB
3696MHz (4*f0)
20dB min.
34dB
4620MHz (5*f0)
20dB min.
36dB
Operating Temperature Range -20~+60ºC
Maximum Rating: (Table 2)
Table 2. Maximum Ratings
Item
Maximum Input Power
Maximum DC Voltage
Operating Temperature Limit
Storage Temperature Limit
Rating
+20dBm
7.5V
-20~+60ºC
-30~+85ºC
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.njr.co.jp/products/device/index.html
http://www.njr.com/products/device/index.html
(Japanese)
(English)
NSTS1449 Apr. 2013
IN
50Ω
1
OUT
50Ω
6
2 SAW 5
3
4
Fig.1 Measuring circuit
(a)
( b)
3. 0±0. 15
3. 0 ± 0. 1 5
222
( c)
K6
(1)
( 0. 6)
( 0. 2 5)
1. 1 5 ± 0. 1 5
( 2)
4
( 0. 6)
[ 2 x]
3
2
5
( 1. 80)
1
( 0. 75)
( 0. 45)
[ 4x]
( 0. 5 3)
[ 4 x]
6
Fig.2 Package dimensions (in mm)
0.93
3.8
1.15
3.8
0.6
2.2
0.93
1.15
Fig.3 Desirable land area (in mm)
Marking
(1) Lot Number
(a) Year
(b) Month
*Oct.--Nov.--Dec.--(c) Date
*1-9--10-19--20-31--(2) Part Number Mark
Pin no.
1
2
3
4
5
6
Connection
GND
IN
GND
GND
OUT
GND
X
Y
Z
0
1
2
NSTS1449 Apr. 2013
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -20ºC or more than +60ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 5 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact New Japan Radio Company before proceeding
with the design of equipment incorporating this product.
3.
The products are designed to be used with ordinary electronic equipment (data
and communications equipment, office equipment, audio-video equipment,
measuring instruments, etc). New Japan Radio Company does not assume any
liability for the case using the products with the application required high
reliability or safety extremely (such as space equipment, sea-bottom equipment,
medical equipment etc). When intending to use any our product please
contact our sales representatives in advance.
NSTS1449 Apr. 2013
Insertion Loss [dB]
0
FREQUENCY CHARACTERISTICS
0
20
2
40
4
60
6
80
8
100
10
CH1 : center 924 span 200
CH2 : center 924 span 200
S11
S22
S22
11
9
9
VSWR
VSWR
S11
11
7
5
3
7
5
3
1
824
1024
1
824
Frequency [MHz]
S21
0
InsertionLoss [dB]
1024
Frequency [MHz]
20
40
60
80
100
0
5000
Frequency [MHz]
New Japan Radio Co.,Ltd.
Insertion Loss [dB]
S21