Document 159-1 Chip Inductors – 0805HS (2012) Ceramic body and wire wound construction provide highest SRFs available in 0805 size. These ultra-compact inductors provide exceptional Q values, even at high frequencies. Part number1 Inductance2 (nH) 0805HS-030TJL_3.3 @250 MHz 0805HS-060TJL_6.8 @250 MHz 0805HS-080TJL_8.2 @250 MHz 0805HS-100TJL_10 @250 MHz 0805HS-120TJL_12 @250 MHz 0805HS-150TJL_15 @250 MHz 0805HS-180TJL_18 @250 MHz 0805HS-220T_L_22 @250 MHz 0805HS-270T_L_27 @250 MHz 0805HS-330T_L_33 @250 MHz 0805HS-390T_L_39 @250 MHz 0805HS-470T_L_47 @200 MHz 0805HS-560T_L_56 @200 MHz 0805HS-680T_L_68 @200 MHz 0805HS-820T_L_82 @150 MHz 0805HS-101T_L_100 @150 MHz 0805HS-121T_L_120 @150 MHz 0805HS-151T_L_150 @100 MHz 0805HS-181T_L_180 @100 MHz 0805HS-221T_L_220 @100 MHz Free evaluation samples are available by contacting Coilcraft or ordering them on-line at www.coilcraft.com. SRF min5 DCR max6 Irms7 Percent Color Q min4 (MHz) (Ohms)(mA) code tolerance3 5 50 @ 1500 MHz 5 50 @ 1000 MHz 5 50 @ 1000 MHz 5 60 @ 500 MHz 5 50 @ 500 MHz 5 50 @ 500 MHz 5 50 @ 500 MHz 5,2 55 @ 500 MHz 5,2 55 @ 500 MHz 5,2 60 @ 500 MHz 5,2 60 @ 500 MHz 5,2 60 @ 500 MHz 5,2,1 60 @ 500 MHz 5,2,160 @ 500 MHz 5,2,165 @ 500 MHz 5,2,165 @ 500 MHz 5,2,150 @ 250 MHz 5,2,150 @ 250 MHz 5,2,150 @ 250 MHz 5,2 50 @ 250 MHz 1. When ordering, specify tolerance, termination and packaging codes: 0805HS-221TJLC Tolerance: F =1% G = 2% J = 5% (Table shows stock tolerances in bold.) Termination:L=RoHS compliant silver-palladium-platinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging:C =7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D =13″ machine-ready reel. EIA-481 embossed plastic tape (7500 parts per full reel). 2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/HP 4286A impedance analyzer with Coilcraft-provided correlation pieces. 3. Tolerances in bold are stocked for immediate shipment. 4. Q measured using an Agilent/HP 4291A with an Agilent/HP 16193 test fixture. 5. SRF measured using an Agilent/HP 8720D network analyzer and a Coilcraft SMD-D test fixture. 6. DCR measured on a Cambridge Technology micro-ohmmeter and a Coilcraft CCF858 test fixture. 7.Current that causes a 15°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 7900 5500 4700 4200 4000 3400 3300 2600 2500 2050 2000 1650 1550 1450 1300 1200 1100 920 870 850 0.08 0.11 0.12 0.10 0.15 0.17 0.20 0.22 0.25 0.27 0.29 0.31 0.34 0.38 0.42 0.46 0.51 0.56 0.64 0.70 600 600 600 600 600 600 600 500 500 500 500 500 500 500 400 400 400 400 400 400 Black Brown Red Blue Orange Yellow Green Blue Violet Gray White Black Brown Red Orange Yellow Green Blue Violet Gray Core material Ceramic Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 9.8 – 10.9 mg Ambient temperature –40°C to +85°C with Irms current Maximum part temperature +100°C (ambient + temp rise). Storage temperature Component: –40°C to +100°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +25 to +125 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 2000/7″ reel; 750/13″ reel Paper tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.3 mm pocket depth PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf. Document 159-1 Revised 10/12/15 Document 159-2 0805HS Series (2012) Typical Q vs Frequency Typical L vs Frequency 100 12 nH 90 1000 3.3 nH 22 nH 39 nH 220 nH 80 6.8 nH 68 nH 120 nH 100 nH Inductance (nH) Q Factor 70 60 50 40 100 39 nH 15 nH 10 30 3.3 nH 20 10 0 1 10 1000 100 10000 Frequency (MHz) B overall A 10 100 1000 Frequency (MHz) H C F I G J F I E terminal Recommended Land Pattern Terminal wraparound: approx 0.015/0,38 both ends ABC maxmaxmax E F G H IJ 0.0850.0600.0570.0500.0200.0400.0700.040 0.030inches 2,161,521,451,270,511,021,781,02 0,76 mm Note: Height dimension (C) is before optional solder application. For maximum height dimension including solder, add 0.006 in / 0,152 mm. Document 159-2 Revised 10/12/15