CA158, CA158A, CA258, CA358, CA358A, CA2904, LM358, LM2904 NO R T DU C E NT PRO LACEM E T OL E RE P OB S E N D E D Data Sheet MM E CO Dual, 1MHz, Operational Amplifiers for Commercial Industrial, and Military Applications tle 15 58 58 58 A3 58 90 3 290 al, z, raal pli- The CA158, CA158A, CA258, CA358, CA358A and CA2904 types consist of two independent, high gain, internally frequency compensated operational amplifiers which are designed specifically to operate from a single power supply over a wide range of voltages. They may also be operated from split power supplies. The supply current is basically independent of the supply voltage over the recommended voltage range. These devices are particularly useful in interface circuits with digital systems and can be operated from the single common 5VDC power supply. They are also intended for transducer amplifiers, DC gain blocks and many other conventional op amp circuits which can benefit from the single power supply capability. CA158 (METAL CAN) TOP VIEW INV. INPUT (A) • Wide Power Supply Range: - Single Supply . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 30V • Dual Supplies . . . . . . . . . . . . . . . . . . . . . . . ±1.5V to ±15V • Low Supply Current . . . . . . . . . . . . . . . . . . . .1.5 mA (Typ) • Low Input Bias Current • Low Input Offset Voltage and Current • Input Common-Mode Voltage Range Includes Ground • Differential Input Voltage Range Equal to V+ Range • Large Output Voltage Swing . . . . . . . . . . . 0V to V+ -1.5V • TB363, Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs) TEMP. RANGE (oC) PACKAGE PKG. NO. CA0158E -55 to 125 8 Ld PDIP E8.3 CA0158AE -55 to 125 8 Ld PDIP E8.3 CA0158M -55 to 125 8 Ld SOIC M8.15 CA0158T -55 to 125 8 Pin Can T8.C CA0258E -25 to 85 8 Ld PDIP E8.3 CA0258M -25 to 85 8 Ld SOIC M8.15 CA0358E 0 to 70 8 Ld PDIP E8.3 CA0358AE 0 to 70 8 Ld PDIP E8.3 CA0358M 0 to 70 8 Ld SOIC M8.15 CA2904E -40 to 85 8 Ld PDIP E8.3 LM358N 0 to 70 8 Ld PDIP E8.3 LM2904N -40 to 85 8 Ld PDIP E8.3 2 NON-INV. INPUT (A) 3 1 OUTPUT (A) - A 8 4 NON-INV. 5 INPUT (B) V+ B 7 OUTPUT (B) 6 INV. INPUT (B) CA158, CA258, CA358 (PDIP, SOIC) CA2904, LM358, LM2904 (PDIP) TOP VIEW OUTPUT (A) 1 INV. INPUT (A) 2 ) • Wide Bandwidth at Unity Gain . . . . . . . . . . . . .1MHz (Typ) PART NUMBER s, li- • High DC Voltage Gain . . . . . . . . . . . . . . . . . . 100dB (Typ) Part Number Information + - • Internal Frequency Compensation for Unity Gain Technical Data on LM Branded types is identical to the corresponding CA Branded types. Pinouts 1019.7 Features Related Literature V- - File Number The CA158, CA158A, CA258, CA358, CA358A, and CA2904 types are an equivalent to or a replacement for the industry types 158, 158A, 258, 258A, 358, 358A, and CA2904. + - May 2001 A B NON-INV. INPUT (A) 3 V- 4 1 8 V+ 7 OUTPUT (B) 6 INV. INPUT (B) 5 NON-INV. INPUT (B) CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Americas Inc. | Copyright © Intersil Americas Inc. 2001 CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904 Absolute Maximum Ratings Thermal Information Supply Voltage CA2904, LM2904 . . . . . . . . . . . . . . . . . . . . . . . . . . . 26V or ±13V Other Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32V or ±16V Differential Input Voltage (All Types) . . . . . . . . . . . . . . . . . . . . . 32V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to V+ Input Current (VI < -0.3V, Note 1) . . . . . . . . . . . . . . . . . . . . . . 50mA Output Short Circuit Duration (V+ ≤ 15V, Note 2) . . . . . .Continuous Thermal Resistance (Typical, Note 3) θJA (oC/W) θJC (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . 130 N/A SOIC Package . . . . . . . . . . . . . . . . . . . 170 N/A Can Package . . . . . . . . . . . . . . . . . . . . 155 67 Maximum Junction Temperature (Can Package). . . . . . . . . . . 175oC Maximum Junction Temperature (Plastic Package). . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range CA158, CA158A . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC CA258, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25oC to 85oC CA2904, LM2904 . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC CA358, CA358A, LM358 . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. This input current will only exist when the voltage at any of the input leads is driven negative. This current is due to the collector base junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the amplifiers to go to the V+ voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This transistor action is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than -0.3V. 2. The maximum output current is approximately 40mA independent of the magnitude of V+. Continuous short circuits at V+ > 15V can cause excessive power dissipation and eventual destruction. Short circuits from the output to V+ can cause overheating and eventual destruction of the device. Destructive dissipation can result from simultaneous short circuits on both amplifiers. 3. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications Values Apply for Each Operational Amplifier. Supply Voltage V+ = 5V, V- = 0V, Unless Otherwise Specified PARAMETER TEST CONDITIONS Input Offset Voltage (Note 6) CA158A CA358A TEMP (oC) MIN TYP MAX MIN TYP MAX UNITS 25 - 1 2 - 2 3 mV Full - - 4 - - 5 mV Average Input Offset Voltage Drift RS = 0Ω Full - 7 15 - 7 20 µV/oC Input Common Mode Voltage Range (Note 5) V+ = 30V 25 0 - V+ -1.5 0 - V+ -1.5 V V+ = 30V Full 0 - V+ -2 0 - V+ -2 V Common Mode Rejection Ratio DC 25 70 85 - 65 85 - dB Power Supply Rejection Ratio DC 25 65 100 - 65 100 - dB Input Bias Current (Note 4) II+ or II- 25 - 20 50 - 45 100 nA II+ or II- Full - 40 100 - 40 200 nA Input Offset Current II+ - II- 25 - 2 10 - 5 30 nA II+ - II- Full - - 30 - - 75 nA Full - 10 200 - 10 300 pA/oC Average Input Offset Current Drift Large Signal Voltage Gain RL ≥ 2kΩ, V+ = 15V (For Large VO Swing) 25 50 100 - 25 100 - kV/V Output Voltage Swing RL = 2kΩ 25 0 - V+ -1.5 0 - V+ -1.5 V 2 CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904 Electrical Specifications Values Apply for Each Operational Amplifier. Supply Voltage V+ = 5V, V- = 0V, Unless Otherwise Specified (Continued) PARAMETER Output Current TEST CONDITIONS CA158A CA358A TEMP (oC) MIN TYP MAX MIN TYP MAX UNITS Source VI+ = +1V, VI- = 0V, V+ = 15V 25 20 40 - 20 40 - mA Sink VI+ = 0V, VI- = 1V, V+ = 15V 25 10 20 - 10 20 - mA VI+ = 0V, VI- = 1V, VO = 200mV 25 12 50 - 12 50 - µA Short Circuit Output Current (Note 2) RL = 0Ω 25 - 40 60 - 40 60 mA Crosstalk f = 1 to 20kHz (Input Referred) 25 - -120 - - -120 - dB Total Supply Current RL = ∞ Full - 0.7 1.2 - 0.7 1.2 mA RL = ∞, V+ = 30V Full - 1.5 3 - 1.5 3 mA NOTES: 4. Due to the PNP input stage the direction of the input current is out of the IC. No loading change exists on the input lines because the current is essentially constant, independent of the state of the output. 5. The input signal voltage and the input common mode voltage should not be allowed to go negative by more than 0.3V. The positive limit of the common mode voltage range is V+ - 1.5V, but either or both inputs can go to +32V without damage. 6. VO = 1.4V, RS = 0Ω with V+ from 5V to 30V, and over the full input common mode voltage range (0V to V+ - 1.5V). Electrical Specifications Values Apply for Each Operational Amplifier. Supply Voltage V+ = 5V, V- = 0V, Unless Otherwise Specified TEST CONDITIONS PARAMETER Input Offset Voltage (Note 9) CA158, CA258 CA358, LM358 CA2904, LM2904 TEMP (oC) MIN TYP MAX MIN TYP MAX MIN TYP MAX UNITS 25 - 2 5 - 2 7 - 2 7 mV Full - - 7 - - 9 - - 10 mV Average Input Offset Voltage Drift RS = 0Ω Full - 7 - - 7 - - 7 - µV/oC Input Common Mode Voltage Range (Note 8) V+ = 30V 25 0 - V+ 1.5 0 - V+ 1.5 0 - V+ 1.5 V V+ = 30V Full 0 - V+ -2 0 - V+ -2 0 - V+ -2 V Common Mode Rejection Ratio DC 25 70 85 - 65 70 - 50 70 - dB Power Supply Rejection Ratio DC 25 65 100 - 65 100 - 50 100 - dB Input Bias Current (Note 7) II+ or II- 25 - 45 150 - 45 250 - 45 250 nA II+ or II- Full - 40 300 - 40 500 - 40 500 nA Input Offset Current II+ - II- 25 - 3 30 - 5 50 - 5 50 nA II+ - II- Full - - 100 - - 150 - 45 200 nA Full - 10 - - 10 - - 10 - pA/oC Average Input Offset Current Drift Large Signal Voltage Gain RL ≥ 2kΩ, V+ = 15V (For Large VO Swing) 25 50 100 - 25 100 - - 100 - kV/V Output Voltage Swing RL = 2kΩ 25 0 - V+ 1.5 0 - V+ 1.5 0 - V+ 1.5 V 3 CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904 Electrical Specifications TEST CONDITIONS PARAMETER Output Current Values Apply for Each Operational Amplifier. Supply Voltage V+ = 5V, V- = 0V, Unless Otherwise Specified (Continued) CA158, CA258 CA358, LM358 CA2904, LM2904 TEMP (oC) MIN TYP MAX MIN TYP MAX MIN TYP MAX UNITS Source VI+ = +1V, VI- = 0V, V+ = 15V 25 20 40 - 20 40 - 20 40 - mA Sink VI+ = 0V, VI- = 1V, V+ = 15V 25 10 20 - 10 20 - 10 20 - mA VI+ = 0V, VI- = 1V, VO = 200mV 25 12 50 - 12 50 - - - - µA Short Circuit Output Current (Note 2) RL = 0Ω 25 - 40 60 - 40 60 - 40 60 mA Crosstalk f = 1 to 20kHz (Input Referred) 25 - -120 - - -120 - - -120 - dB Total Supply Current RL = ∞ Full - 0.7 1.2 - 0.7 1.2 - 0.7 1.2 mA RL = ∞, V+ = 30V Full - 1.5 3 - 1.5 3 - 1.5 3 mA NOTES: 7. Due to the PNP input stage the direction of the input current is out of the IC. No loading change exists on the input lines because the current is essentially constant, independent of the state of the output. 8. The input signal voltage and the input common mode voltage should not be allowed to go negative by more than 0.3V. The positive limit of the common mode voltage range is V+ - 1.5V, but either or both inputs can go to +32V without damage. 9. VO = 1.4V, RS = 0Ω with V+ from 5V to 30V, and over the full input common mode voltage range (0V to V+ - 1.5V). Schematic Diagram ONE OF TWO OPERATIONAL AMPLIFIERS 8 V+ TO 2 6µA 4µA 100 µA 2 5 Q2 - 2 Q3 - 6 CCOMP Q1 + Q5 Q6 Q4 INPUTS Q7 + Q11 3 RSC Q10 1 Q8 VO Q9 Q13 Q12 50µA TO 2 4 4 V- 7 CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904 Typical Performance Curves VICR = 0V 60 V+ = 30V 50 INPUT CURRENT (nA) INPUT VOLTAGE (V) 15 10 NEGATIVE POSITIVE 5 40 15V 30 5V 20 10 0 -75 0 5 10 15 -50 -25 0 20 25 50 75 100 125 TEMPERATURE (oC) SUPPLY VOLTAGE (V) FIGURE 1. INPUT VOLTAGE RANGE vs SUPPLY VOLTAGE FIGURE 2. INPUT CURRENT vs AMBIENT TEMPERATURE V+ SUPPLY CURRENT DRAIN (mA) mA 4 ID - + 3 2 TA = 0oC TO 125 oC 1 -55 oC 0 5 10 15 20 25 COMMON MODE REJECTION RATION (dB) 120 100 +7.5VDC 80 100K 60 100 - 40 VO + + VIN 100 100K -7.5VDC 20 0 100 30 1K POSITIVE SUPPLY VOLTAGE (V) 10K 100K 1M INPUT FREQUENCY (Hz) FIGURE 3. SUPPLY CURRENT DRAIN vs SUPPLY VOLTAGE FIGURE 4. COMMON MODE REJECTION RATIO vs INPUT FREQUENCY 140 TA = 25 oC OPEN-LOOP VOLTAGE GAIN (dB) 10MΩ OPEN LOOP VOLTAGE GAIN (dB) 150 RL = 20kΩ 125 2kΩ 100 75 50 25 0 0 10 20 30 40 POSITIVE SUPPLY VOLTAGE (V) FIGURE 5. VOLTAGE GAIN vs SUPPLY VOLTAGE 5 120 V+ 0.1µF 100 - VO + VI 80 V+ / 2 V+ = 10 TO 15V 60 V+ = 26V 40 20 TA = -40 ≤ TA ≤ 85oC 0 1 10 100 1K 10K 100K FREQUENCY (Hz) 1M FIGURE 6. OPEN-LOOP FREQUENCY RESPONSE 10M CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904 Typical Performance Curves (Continued) 4 3 2 1 INPUT VOLTAGE (V) 0 4 3 OUTPUT VOLTAGE (mV) OUTPUT VOLTAGE (V) TA = 25 oC V+ = 30V TA = 25oC V+ = 15V RL = 2kΩ 500 - + 450 VO 50pF VI INPUT 400 350 OUTPUT 2 300 1 250 0 0 10 20 30 TIME (µs) 0 40 FIGURE 7. VOLTAGE FOLLOWER PULSE RESPONSE (LARGE SIGNAL) 20 TA = 25 oC 1 2 3 4 5 TIME (µs) 6 7 8 9 FIGURE 8. VOLTAGE FOLLOWER PULSE RESPONSE (SMALL SIGNAL) TA = 25oC 100kΩ 1kΩ 15 +15V VO - + +7V 2kΩ VI 10 INPUT CURRENT (nA) OUTPUT VOLTAGE SWING (V) 75 5 0 50 25 0 1K 10K 100K 1M 0 FREQUENCY (Hz) FIGURE 9. LARGE-SIGNAL FREQUENCY RESPONSE 10 20 30 POSITIVE SUPPLY VOLTAGE (V) FIGURE 10. INPUT CURRENT vs SUPPLY VOLTAGE 10 8 V+ V+ = +5VDC V+ = +15 VDC V+ = +30VDC V+ / 2 VO OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) (REFERENCED TO V+) 7 6 40 + - 5 IO+ INDEPENDENT OF V+ TA = 25oC 4 3 1 V+ V+ / 2 - 0.1 IO + VO 2 1 TA = 25oC 0.01 0.001 0.01 0.1 1 10 100 OUTPUT SOURCE CURRENT (mA) FIGURE 11. OUTPUT SOURCE CURRENT CHARACTERISTICS 6 0.001 0.01 0.1 1 10 100 OUTPUT SINK CURRENT (mA) FIGURE 12. OUTPUT SINK CURRENT CHARACTERISTICS CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904 Typical Performance Curves (Continued) 70 OUTPUT SOURCE CURRENT (mA) V+ = 15V 60 50 40 30 20 10 0 -75 -50 -25 0 25 50 75 100 125 TEMPERATURE (oC) FIGURE 13. OUTPUT CURRENT vs AMBIENT TEMPERATURE Metallization Mask Layout 0 10 20 30 40 50 60 66 72 70 60 50 40 69 - 77 (1.753 - 1.956) 30 20 10 0 4 - 10 (0.102 - 0.254) 63 - 71 (1.600 - 1.803) Dimensions in parentheses are in millimeters and derived from the basic inch dimensions as indicated. Grid graduations are in mils (10-3 inch). The photographs and dimensions represent a chip when it is part of the wafer. When the wafer is cut into chips, the cleavage angles are 57o instead of 90o with respect to the face of the chip. Therefore, the isolated chip is actually 7mils (0.17mm) larger in both dimensions. All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com 7