CCDLF

Document 511-1
SMT Data Line EMI Filters – CCDLF
• Available in 10 and 8-line versions
• See our PDLF series for 4, 3 and 2-line EMI filters
• Exceptional common mode noise attenuation from 15 MHz to
300 MHz; passes signal line data below 300 MHz with minimal
attenuation
• DC current capacity of 500 or 100 mA.
• Excellent electrical isolation (300 Vrms)
CCDLF 10000L_10
100
5
CCDLF 8000L_8 100 5
CCDLF 8500L_8 500 5
250
250
200
1. When ordering, please specify termination and packaging codes:
CCDLF 8500LD
TerminationL =RoHS compliant tin-silver-copper over silver-platinum
Special order: S = non-RoHS tin-lead (63/37).
PackagingD =13″ machine ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B
=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
2. Current rating is for each line.
3. Inductance is per winding, tested at 1 MHz.
4. Operating temperature range -40°C to +85°C.
5. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Typical Response*
-10
Attenuation (dB)
Current
L min DCR max
Part number1Lines
max (mA)2 (µH)3(mOhms)
Designer’s Kit D303 contains four each of all values plus DLF and
PDLF filters
Core material Ferrite
Terminations RoHS compliant tin-silver-copper over silver-platinum.
Other terminations available at additional cost.
Weight CCDLF 8000: 540 mg; CCDLF 8500: 559 mg;
CCDLF 10000: 670 mg
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Mean Time Between Failures (MTBF) 26,315,789 hours
Packaging 1000/13″ reel Plastic tape: 16 mm wide
CCDLF8x00: 10.46 mm thick, 12 mm pocket spacing,
4.5 mm pocket depth
CCDLF10000: 10.28 mm thick, 12 mm pocket spacing,
5.0 mm pocket depth
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf
Differential Mode
0
10
20
Common Mode
30
0.1
1
10
100
1000
Frequency (MHz)
*Measured on HP 8753D network analyzer. Ref: 50 Ohms.
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 511-1 Revised 11/19/10
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
Document 511-2
Surface Mount Data Line EMI Filters
CCDLF 10000
0.060 ref
1,52
0.040 typ
1,02
Recommended
Land Pattern
0.020
0,51
0.030
0,76
0.360max
9,14
5
3
4
2
16 17 18 19 20 5 4 3 2 1
1
6
20
7
19
0.270 0.230 8
6,86 5,84
1
20
Dimensions are in
0.360 max
9,14
0.170 max
4,32
11 12 13 14
0.030
0,76
15 14 13 12 11 6 7 8 9 10
17
0.050cen
1,27
10
16
0.050
1,27
15
inches
mm
CCDLF 8000, 8500
0.060ref
1,52
0.040 typ
1,02
0.305 max
7,75
16
0.305 max
7,75
4
2
8 7 6 5 9 10 11 12
1
16
6
15
0.050cen
1,27
8
9
0.170max
4,32
3
5
0.220 0.180
5,59 4,57 7
0.050 cen
1,27
1
Recommended
Land Pattern
0.020
0,51
0.030
0,76
Dimensions are in
18
9
0.050 cen
1,27
14
1 2 3 4 16 15 14 13
13
10 11 12
0.050
1,27
0.030
0,76
inches
mm
LF
D
C
C
Dot indicates
pin 1
L
00
80
X
Parts manufactured prior
to Sept 2007 may not be
marked with part number
and internal code.
Part number
Internal code
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 511-2 Revised 11/19/10
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.