COILCRAFT CCDLF8500L

Document 511-1
SMT Data Line EMI Filters – CCDLF
• Available in 10 and 8-line versions
• See our PDLF series for 4, 3 and 2-line EMI filters
• Exceptional common mode noise attenuation from 15 MHz
to 300 MHz; passes signal line data below 300 MHz with
minimal attenuation
• DC current capacity of 500 or 100 mA.
• Excellent electrical isolation (300 Vrms)
Designer’s Kit D303 contains four each of all values plus DLF and
PDLF filters
Core material Ferrite
Terminations RoHS compliant tin-silver-copper over silverplatinum. Other terminations available at additional cost.
Weight CCDLF 8000: 540 mg;
10000: 670 mg
CCDLF 8500: 559 mg;CCDLF
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Part number1
Lines
Current
max
(mA)2
CCDLF 10000L_
CCDLF 8000L_
CCDLF 8500L_
10
8
8
100
100
500
L
DCR
min
max
Color
(µH)3 (mOhms) Dot
5
5
5
250
250
200
Brown
Black
Green
1. When ordering, please specify termination and packaging codes:
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Mean Time Between Failures (MTBF) 26,315,789 hours
Packaging 1000/13″ reel Plastic tape: 16 mm wide
CCDLF8x00: 10.46 mm thick, 12 mm pocket spacing,
4.5 mm pocket depth
CCDLF10000: 10.28 mm thick, 12 mm pocket spacing,
5.0 mm pocket depth
PCB washing Only pure water or alcohol recommended
CCDLF 8500LD
Typical Response*
-10
Attenuation (dB)
Termination L = RoHS compliant tin-silver-copper over silver-platinum
Special order: S = non-RoHS tin-lead (63/37).
Packaging D = 13″ machine ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B = Less than full reel. In tape, but not machine ready. To
have a leader and trailer added ($25 charge), use
code letter D instead.
2. Current rating is for each line.
3. Inductance is per winding, tested at 1 MHz.
4. Operating temperature range -40°C to +85°C.
5. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Differential Mode
0
10
20
Common Mode
30
0.1
1
10
100
1000
Frequency (MHz)
*Measured on HP 8753D network analyzer. Ref: 50 Ohms.
Specifications subject to change without notice.
Please check our website for latest information.
© Coilcraft, Inc. 2009
Document 511-1
Revised 10/30/08
Document 511-2
Surface Mount Data Line EMI Filters
CCDLF 10000
0.060 ref
1,52
0.040 typ
1,02
0.030
0,76
0.360max
9,14
5
3
16 17 18 19 20 5 4 3 2 1
1
2
6
20
19
0.270 0.230 8
6,86 5,84
18
0.050cen
1,27
10
11 12 13 14
0.170 max
4,32
15 14 13 12 11 6 7 8 9 10
17
9
20
0.360 max
9,14
4
7
0.050 cen
1,27
1
Recommended
Land Pattern
0.020
0,51
16
0.050
1,27
15
0.030
0,76
inches
mm
Dimensions are in
CCDLF 8000, 8500
0.060ref
1,52
0.040 typ
1,02
0.030
0,76
0.305 max
7,75
16
0.305 max
7,75
4
2
8 7 6 5 9 10 11 12
1
16
6
15
14
0.050cen
1,27
8
9
0.170max
4,32
3
5
0.220 0.180
5,59 4,57 7
0.050 cen
1,27
1
Recommended
Land Pattern
0.020
0,51
10 11 12
1 2 3 4 16 15 14 13
13
0.050
1,27
0.030
0,76
inches
mm
Dimensions are in
C
Dot indicates
pin 1
LF
D
C
L
00
80
X
Parts manufactured prior
to Sept 2007 may not be
marked with part number
and internal code.
Part number
Internal code
Specifications subject to change without notice.
Please check our website for latest information.
© Coilcraft, Inc. 2009
Document 511-2
Revised 10/30/08