LPS3008

Document 438-1
Shielded Power Inductors – LPS3008
• Very low DCR; excellent current handling
• Only 0.8 mm tall; 3.0 × 3.0 mm footprint
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Environmental RoHS compliant, halogen free
Terminations RoHS compliant matte tin over nickel over silver.
Other terminations available at additional cost.
Weight 22 – 25 mg
Ambient temperature –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature +125°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.37 mm pocket depth
Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Isat (A)5 Irms (A)6
DCR SRF
2
3
4
Inductance max typ 10% 20% 30% 20°C40°C
Part number1 ±20% (µH) (Ohms)(MHz) drop drop drop rise rise
LPS3008-561MR_ 0.56 0.072
3301.82.02.11.42.0
LPS3008-801MR_ 0.80 0.092
2551.61.71.81.11.6
LPS3008-102MR_ 1.0 0.125
2201.31.41.50.90
1.3
LPS3008-152MR_ 1.5 0.134
1701.11.31.30.87
1.2
LPS3008-222MR_ 2.2 0.175
1501.01.11.10.85
1.1
LPS3008-332MR_
LPS3008-472MR_
LPS3008-562MR_
LPS3008-682MR_
LPS3008-822MR_
3.3
4.7
5.6
6.8
8.2
0.285114 0.810.860.880.740.95
0.350 87 0.680.730.740.680.80
0.450 78 0.620.670.700.580.73
0.500 75 0.580.610.630.500.67
0.600 61 0.520.560.580.450.60
LPS3008-103MR_ 10
LPS3008-123MR_ 12
LPS3008-183MR_ 18
LPS3008-223MR_ 22
LPS3008-333MR_ 33
0.650
0.790
1.25
1.50
2.30
56 0.460.510.520.420.56
49 0.450.480.500.380.50
38 0.350.380.400.330.44
35 0.290.330.340.290.38
23 0.270.300.310.250.32
LPS3008-473MR_ 47
LPS3008-683MR_ 68
LPS3008-104MR_100
LPS3008-124MR_ 120
LPS3008-154MR_ 150
3.00
4.75
6.85
7.00
8.00
21 0.220.230.240.210.27
18 0.180.190.200.175
0.23
14 0.150.160.160.160
0.21
13 0.0840.0940.10 0.1400.190
11 0.0800.0880.0920.1300.175
LPS3008-184MR_ 180
9.00
10 0.0700.0780.0820.1200.160
Coilcraft Designer’s Kit C392 contains samples of 0.80 µH to 33 µH parts (3 each)
from LPS3008, LPS3010 and LPS3015. Kit C401 contains samples of 0.56 µH to
33 µH parts (3 each) from LPS4012 and LPS4018. Kit C402 contains samples of
220 µH to 3300 µH parts (3 each) from all five series. For details of kit contents and
to order, contact Coilcraft or visit http://order.coilcraft.com.
1. Please specify termination and packaging codes:
LPS3008-104MRC
Termination:R=RoHS compliant matte tin over
nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5)
or P = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481
embossed plastic tape (1000 parts
per full reel).
B=Less than full reel. In tape, but not
machine ready. To have a leader
and trailer added ($25 charge), use
code letter C instead.
D
=13″ machine-ready reel. EIA-481
embossed plastic tape. Factory
order only, not stocked (3500 parts
per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an
Agilent/HP 4192A. Inductance at 1 MHz is the same
for parts with SRF ≥10 MHz.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using an Agilent/HP 8753ES or
equivalent.
5. DC current at 25°C that causes the specified inductance drop from its value without current. lick for
temperature derating information.
6. Current that causes the specified temperature rise
from 25°C ambient. This information is for reference
only and does not represent absolute maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 438-1 Revised 09/01/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
Document 438-2
Shielded Power Inductors – LPS3008 Series
Typical L vs Current
Typical L vs Frequency
1000
1000
330 µH
100
100 µH
Inductance (µH)
Inductance (µH)
330 µH
33 µH
10
10 µH
3.3 µH
1
0.1
1
0.1
33 µH
10 µH
10
3.3 µH
1.0 µH
1
1.0 µH
0.01
100 µH
100
10
0.1
0.01
1
0.1
Current (A)
10
Frequency (MHz)
Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.37 mm pocket depth
NOTE NEW PART ORIENTATION Parts are rotated 90° in the
packaging tape compared to previous versions of this product.
NEW
123
123
123
Dimensions are in
OLD
123
123
123
inches
mm
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 438-2 Revised 09/1/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.