LPS3010

Document 428-1
Shielded Power Inductors – LPS3010
• Ultra small 3.0 × 3.0 mm footprint; less than 1.0 mm tall
• Very low DCR; excellent current handling
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Environmental RoHS compliant, halogen free
Terminations RoHS compliant matte tin over nickel over silver.
Other terminations available at additional cost.
Weight 25 – 32 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth
Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Isat (A)5 Irms (A)6
DCR SRF
Inductance2 max3 typ4 10% 20% 30% 20°C40°C
Part number1 ±20% (µH) (Ohms)(MHz) drop drop drop rise rise
LPS3010-471MR_ 0.47 0.070
3701.81.92.01.31.80
LPS3010-681MR_ 0.68 0.080
2701.61.71.71.31.75
LPS3010-102MR_ 1.0 0.085
2301.51.61.61.11.50
LPS3010-152MR_ 1.5 0.120
1651.31.41.41.05
1.40
LPS3010-182MR_ 1.8 0.150
1501.21.21.31.00
1.40
LPS3010-222MR_ 2.2
LPS3010-332MR_ 3.3
LPS3010-472MR_ 4.7
LPS3010-562MR_ 5.6
LPS3010-682MR_ 6.8
0.220
1301.31.41.40.90
1.10
0.220110 0.830.880.900.851.10
0.300 92 0.720.750.770.700.95
0.400 80 0.670.690.710.600.78
0.450 70 0.610.630.640.560.74
LPS3010-822MR_ 8.2
LPS3010-103MR_ 10
LPS3010-123MR_ 12
LPS3010-153MR_ 15
LPS3010-183MR_ 18
0.520
0.540
0.700
0.950
1.10
62 0.560.590.590.530.70
58 0.500.530.550.480.64
47 0.460.490.500.440.58
43 0.410.430.440.370.48
40 0.380.400.410.330.47
LPS3010-223MR_ 22
LPS3010-333MR_ 33
LPS3010-473MR_ 47
LPS3010-683MR_ 68
LPS3010-104MR_100
1.20
2.00
3.20
3.50
5.25
36 0.320.350.360.300.41
27 0.250.270.280.260.35
21 0.230.240.250.220.31
21 0.200.210.220.200.28
14 0.140.160.170.180.24
LPS3010-124MR_120
LPS3010-154MR_150
LPS3010-184MR_180
LPS3010-224MR_220
6.10
9.15
10.1
12.5
12 0.130.150.150.140.19
11 0.130.140.140.130.17
9 0.110.120.130.110.15
8 0.100.110.120.095
0.13
1. Please specify termination and packaging codes:
LPS3010-223MRC
Termination:R=RoHS compliant matte tin over
nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5)
or P = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481
embossed plastic tape (1000 parts
per full reel).
B=Less than full reel. In tape, but not
machine ready.
To have a leader and trailer added
($25 charge), use code letter C
instead.
D
=13″ machine-ready reel. EIA-481
embossed plastic tape. Factory
order only, not stocked (3500 parts
per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an
Agilent/HP 4192A. Inductance at 1 MHz is the same
for parts with SRF ≥10 MHz.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using an Agilent/HP 8753ES or
equivalent.
5. DC current that causes the specified inductance drop
from its value without current.
6. Current that causes the specified temperature rise
from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
Coilcraft Designer’s Kit C392 contains samples of 0.80 µH to 33 µH parts (3 each)
from LPS3008, LPS3010 and LPS3015. Kit C401 contains samples of 0.56 µH to
33 µH parts (3 each) from LPS4012 and LPS4018. Kit C402 contains samples of
220 µH to 3300 µH parts (3 each) from all five series. For details of kit contents and
to order, contact Coilcraft or visit http://order.coilcraft.com.
Document 428-1 Revised 08/02/13
Document 428-2
Shielded SMT Power Inductors – LPS3010 Series
L vs Frequency
L vs Current
1000
1000
330 µH
100
68 µH
Inductance (µH)
Inductance (µH)
330 µH
33 µH
6.8 µH
10
3.3 µH
1
0.1
0.68 µH
0.01
0.1
1
10
Frequency (MHz)
100
68 µH
33 µH
6.8 µH
10
3.3 µH
1
0.1
0.68 µH
0.01
0.1
Current (A)
1
10
Typical Current Derating
120
100
90
80
70
60
50
40
30
20
25°C
Percent of rated Current
110
Isat
Irms
10
0
-40
-20
0
20
40
60
80
100
120 140
Ambient temperature (°C)
Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth
NOTE NEW PART ORIENTATION Parts are rotated 90° in the
packaging tape compared to previous versions of this product.
NEW
Dimensions are in
inches
mm
OLD
123
123
123
123
123
123
Document 428-2 Revised 08/02/13