PFD2015

Document 1005C-1
Common Mode Chokes – PFD2015
• Miniature surface mount component, only 2.2 × 1.45 mm
footprint and 1.5 mm tall
• Eliminates virtually all common mode noise
• Designed for high-speed applications
• Nine values to meet your specific requirements
• Low DCR values
Part number1
Inductance2
min (µH)
DCR
max3Isolation4 Irms5
(Ohms)
(Vrms)
Core material Ferrite
Environmental RoHS compliant, halogen free
Weight 13 – 23 mg
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Ambient temperature –40°C to +125°C
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 2000/7″ reel; 7500/13″ reel Plastic tape: 8 mm wide,
0.23 mm thick, 4 mm pocket spacing, 1.63 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
(A)
PFD2015-102ME_0.80
PFD2015-122ME_0.96
PFD2015-182ME_1.44
PFD2015-272ME_2.16
PFD2015-332ME_2.64
0.165
0.175
0.294
0.477
0.670
250
250
250
250
250
0.800
0.750
0.490
0.410
0.370
PFD2015-472ME_3.76
PFD2015-682ME_5.44
PFD2015-822ME_6.56
PFD2015-103ME_8.00
1.00
1.75
2.50
3.40
250
250
250
250
0.260
0.187
0.150
0.130
0.090
max
2,29
1. When ordering, please specify packaging code:
PFD2015-103MEC
Packaging: C= 7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
D= 13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (7500 parts per
full reel).
2. Inductance measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP
4284A LCR meter or equivalent.
3. DCR is for each winding.
4. Interwinding isolation for one minute
5. Current that causes a 40°C temperature rise from 25°C ambient.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
1
2
4
3
0.059 max
1,5
0.054
1,36
0.010
0,25
1
4
0.044
1,118
0.028
0,711
0.014 ±0.003
0,356 ±0,076
2
4
3
1
2
0.016
0,406
0.060
max
1,52
3
0.017
0,432
Recommended
Land Pattern
0.022
0,559
Dimensions are in inches
mm
Specifications subject to change without notice.
Please check our website for latest information.
Document 1005C-1 Revised 09/08/15
Document 1005C-2
PFD2015 Common Mode Chokes
Attenuation (dB)
Typical Attenuation (Ref: 50 Ohms)
0
5
10
-103 -682 -332 -182 -102
15
20
Differential mode
0.1
1
10
100
1000
Frequency (MHz)
0
5
10
Attenuation (dB)
15
-102
20
25
30
-182
-332
35
-682
40
-103
45
50
Common mode
0.1
1
10
100
1000
Frequency (MHz)
Typical Impedance vs Frequency
100
-103
-682
Impedance (kOhms)
10
-332
-182
1
-102
0.1
0.01
0.001
0.1
1
10
100
1000
Frequency (MHz)
Specifications subject to change without notice.
Please check our website for latest information.
Document 1005C-2 Revised 09/08/15