PFL2015

Document 876-1
Shielded Power Inductors – PFL2015
• Low cost, low profile 0805 size power inductor
• Can handle current of much larger inductors; up to 1900 mA
Core material Composite
Core and winding loss See www.coilcraft.com/coreloss
Environmental RoHS compliant, halogen free
Terminations RoHS compliant matte tin over nickel over silverplatinum-glass frit. Other terminations available at additional cost.
Weight 14.1 mg
Ambient temperature –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature +125°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 2000/7″ reel; 7500/13″ reel. Plastic tape: 8 mm wide,
0.23 mm thick, 4 mm pocket spacing, 1.63 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Part number1
Inductance2 ±20% (µH)
3
DCR (mOhms) typ
max
5
6
typ4 Isat (mA) Irms (mA) (MHz)
10% drop 20% drop 30% drop 20°C rise 40°C rise
SRF
PFL2015-561ME_
0.56 60
70 60013001600
19001300
1800
PFL2015-681ME_
0.68 62
75 46012001600
18001100
1500
PFL2015-102ME_
1.0 110
130 450 900 12001400 9401200
PFL2015-222ME_
2.2175
210100640840
1050770
1000
PFL2015-332ME_
3.3255
280 60480650
720700
900
PFL2015-472ME_
4.7275
340 50450620
700600
770
PFL2015-682ME_
6.8340
400 40380520
600520
680
1. When ordering, please specify termination and packaging codes:
PFL2015-682MEC
Termination:E=RoHS compliant matte tin over nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel).
B
=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (7500 parts per full reel).
2. Inductance tested at 7.9 MHz, 0.1 Vrms using a Coilcraft SMD-A test fixture with an Agilent/HP 4286 impedance analyzer and Coilcraft-provided correlation pieces.
3. DCR measured using a micro-ohmmeter.
4. SRF measured using an Agilent/HP 8753D network analyzer and a Coilcraft SMD-D test fixture.
5. DC current at 25°C that causes the specified inductance drop from its value without current. Click for temperature derating information.
6. Current that causes the specified temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum
ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 876-1 Revised 09/13/15
Document 876-2
PFL2015 Series
L vs Frequency
L vs Current
10
10
6.8 µH
6.8 µH
4.7 µH
3.3 µH
3.3 µH
Inductance (µH)
Inductance (µH)
4.7 µH
2.2 µH
1
1.0 µH
0.68 µH
0.56 µH
0.1
2.2 µH
1.0 µH
1
0.68 µH
0.56 µH
0.1
0.01
1
0.1
10
Current (A)
0.1
1
10
100
Frequency (MHz)
0.087
max
2,20
0.015
0,38
0.059
max
1,50
Terminal wraparound:
approx 0.010/0,254 both ends
0.012
0,305
0.056
1,42
0.012
0,305
0.050
1,27
0.057 max
1,45
0.070
1,78
0.070
1.78
0.040
1,02
Dimensions are in
inches
mm
Recommended
Land Pattern
Document 876-2 Revised 09/13/15