SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage TwinSLIC™ Series - Modified DO-214 Pb e3 RoHS Description Fixed Voltage Series Modified DO-214 are uni-directional SIDACtor® thyristors designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. The series provides single port protection using fixed voltage switching components for negative surges. All positive surges are routed through internal diodes to a ground reference. Features and Benefits • Low voltage overshoot • Single-port protection • Low on-state voltage Agency Approvals Agency positive voltage surges • Does not degrade surge • RoHS Compliant and Halogen-Free capability after multiple surge events within limit. • Pb-free E3 means 2nd level interconnect is • Fails short circuit when Pb-free and the terminal surged in excess of finish material is tin(Sn) ratings (IPC/JEDEC J-STD• Integrated diodes for 609A.01) Agency File Number E133083 Pinout Designation Pin 3 Applicable Global Standards Pin 1 Pin 2 3 (R) • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 2nd edition • ITU K.20/21 Enhanced Level* Schematic Symbol 1 (T) • TIA-968-A • YD/T 1082 • ITU K.20/21 Basic Level • YD/T 993 • GR 1089 Inter-building* • YD/T 950 * Series resistance required 2 (G) Additional Information Datasheet Samples Resources Electrical Characteristics Part Number Marking VDRM @lDRM=5µA VS @100V/µs V min V max Pin 1-2, 3-2 P0641CA2LRP P0721CA2LRP P0901CA2LRP P1101CA2LRP P1301CA2LRP P1701CA2LRP P62A P72A P92A P02A P131A P17A 58 65 75 95 120 160 77 88 98 130 160 200 IH IS IT mA min mA max A max 120 120 120 120 120 120 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps VF V max V max 4 4 4 4 4 4 5 5 5 5 5 5 Capacitance See Capacitance Values table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are not appropriate for positive ringing systems. © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16 SIDACtor ® Protection Thyristors SLIC Protection Capacitance Values pF Pin 1-2 / 3-2 Tip-Ground, Ring-Ground MIN MAX 40 70 35 70 30 65 25 55 25 45 25 40 Part Number P0641CA2LRP P0721CA2LRP P0901CA2LRP P1101CA2LRP P1301CA2LRP P1701CA2LRP pF Pin 1-3 Tip-Ring MIN 20 20 20 15 15 15 MAX 45 45 40 35 30 25 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings Series Series IPP ITSM di/dt 0.2/310 0.5/700 2 2/10 2/10 2 8/20 1.2/50 2 10/160 10/160 2 10/560 1 10/560 2 5/320 1 9/720 2 10/360 1 10/360 2 10/1000 1 10/1000 2 5/310 1 10/700 2 50/60 Hz A min A min A min A min A min A min A min A min A min A min A/µs max 20 150 150 90 50 75 75 45 75 20 500 A 1 Notes: 1 Current waveform in µs 2 Voltage waveform in µs 1 1 1 - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package Symbol Parameter Value Unit Modified DO-214AA TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 85 °C/W Pin 1 Pin 2 V-I Characteristics tr x td Pulse Waveform +I VS VDRM VF VT -V IDRM IH IS IT -I © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16 +V IPP – Peak Pulse Current – %IPP Pin 3 Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (µs) SIDACtor ® Protection Thyristors SLIC Protection Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 10 IH 8 6 25 °C 4 IH (TC = 25ºC) 12 2 0 -4 1.8 1.6 1.4 25°C 1.2 1.0 Ratio of Percent of VS Change – % 14 0.8 0.6 -6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL Recognized epoxy meeting flammability classification V-0 Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C peak). JEDEC-J-STD-020, Level 1 © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16 SIDACtor ® Protection Thyristors SLIC Protection Compak PM Drawing for pg 100 Fixed Volt TwinSLIC.eps Part Marking Part Numbering P xxx1 C A 2 L RP RoHS COMPLIANT MEDIAN VOLTAGE TwinSLIC IDENTIFIER (two chip device) CONSTRUCTION VARIABLE Part number code XXXXX XXXXX REEL PACK TYPE P = SIDACtor (refer to Electrical Characteristics table) Date code IPP RATING PACKAGE TYPE Dimensions — Modified DO-214AA PIN 3 B D M N A C PIN 1 PIN 2 H E J 0.079 (2.0) 0.079 (2.0) F K G 0.079 (2.0) 0.040 (1.0) 0.110 (2.8) 0.030 (0.76) Inches Dimensions P Dimensions are in inches (and millimeters). A B C D E F G H K M N P Millimeters Min Max Min Max 0.130 0.201 0.077 0.159 0.030 0.075 0.002 0.077 0.006 0.022 0.027 0.052 0.156 0.220 0.087 0.181 0.063 0.096 0.008 0.104 0.016 0.028 0.033 0.058 3.30 5.10 1.95 4.05 0.75 1.90 0.05 1.95 0.15 0.56 0.69 1.32 3.95 5.60 2.20 4.60 1.60 2.45 0.20 2.65 0.41 0.71 0.84 1.47 Pad Outline (MM) Packing Options Package Type C Description Quantity Added Suffix Industry Standard Modified DO-214AA 3-leaded Tape and Reel Pack 2500 RP EIA-481-D Tape and Reel Specification — Modified DO-214AA 0.157 0.157 (4.0) (4.0) Pin 2 0.472 0.472 (12.0) 0.36 (12.0) (9.2) 0.360 (9.2) 0.315 (8.0) Pin 1 0.315 (8.0) 12.99 (330.0) 0.512 (13.0) Arbor Hole Dia. 0.49 (12.4) © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16 Dimensions are in inches Pin 3 0.059 (and millimeters). DIA Cover tape (1.5) Dimensions are in inches (and millimeters). Direction of Feed