pdf

EC-Declaration of Conformity
Annex
Document number: 2012 / QTP8_03
The conformity of the designated product(s) with the provisions of the European Directive
2006/95/EC is given by the compliance with the following European Standard(s). If not
elsewhere/otherwise indicated the edition/amendment as referenced below applies.
EN 61347-1:
2008 + A1:2011
Lamp controlgear — Part 1: General and safety requirements
EN 61347-2-1.
2001 +
Corrigendum:2003 +
A1:2006 +
Corrigendum:2006
Corrigendum:2010
Lamp controlgear — Part 2-1: Particular requirements for starting devices (other
than glow starters)
EN 61347-2-2:
2012
Lamp controlgear — Part 2-2: Particular requirements for d. c. or a. c. supplied
electronic step-down convertors for filament lamps
EN 61347-2-3:
2011
Lamp controlgear — Part 2-3: Particular requirements for a. c. supplied
electronic ballasts for fluorescent lamps
EN 61347-2-7:
2012
Lamp controlgear — Part 2-7: Particular requirements for battery supplied
electronic controlgear for emergency lighting (self-contained)
EN 61347-2-8:
2001 +
Corrigendum:2003 +
A1:2006 +
Corrigendum:2010
Lamp controlgear — Part 2-8: Particular requirements for ballasts for
fluorescent lamps
EN 61347-2-9:
2001 +
Corrigendum:2003 +
A1:2003 + A2:2006 +
Corrigendum:2010
Lamp controlgear — Part 2-9: Particular requirements for ballasts for discharge
lamps (excluding fluorescent lamps)
EN 61347-2-10:
2001 + A1:2009 +
Corrigendum:2010
Lamp controlgear — Part 2-10: Particular requirements for electronic invertors
and convertors for high-frequency operation of cold start tubular discharge
lamps (neon tubes)
EN 61347-2-11:
2001 +
Corrigendum:2002 +
Corrigendum:2010
Lamp controlgear — Part 2-11: Particular requirements for miscellaneous
electronic circuits used with luminaires
EN 61347-2-12:
2005 + A1:2010
Lamp controlgear — Part 2-12: Particular requirements for d. c. or a. c. supplied
electronic ballasts for discharge lamps (excluding fluorescent lamps)
EN 61347-2-13:
2006
Lamp controlgear — Part 2-13: Particular requirements for d. c. or a. c. supplied
electronic controlgear for LED modules
EN 61549:
2003 + A1:2005 +
A2:2010
Miscellaneous lamps
EN 62031:
2008
LED modules for general lighting — Safety specifications
EN 62034:
2006
Automatic test systems for battery powered emergency escape lighting
EN 62035:
2000 + A1:2003
Discharge lamps (excluding fluorescent lamps) — Safety specifications
EN 62471:
2008
Photobiological safety of lamps and lamp systems
IEC/TR 62471-2:
2009
Photobiological safety of lamps and lamp systems — Part 2: Guidance on
manufacturing requirements relating to non-laser optical radiation safety
2/5
Form_EC_120430
EC-Declaration of Conformity
Annex
Document number: 2012 / QTP8_03
EN 62560:
XXXX
Self-ballasted LED-lamps for general lighting services by voltage > 50 V —
Safety specifications
The conformity of the designated product(s) with the provisions of the European Directive
2004/108/EC is given by the compliance with the following European Standard(s). If not
elsewhere/otherwise indicated the edition/amendment as referenced below applies.
EN 55015:
2006 + A1:2007
+ A2:2009
Limits and methods of measurement of radio disturbance characteristics of electrical
lighting and similar equipment
EN 61000-3-2:
2006 + A1:2009
+ A2:2009
Electromagnetic compatibility (EMC) — Part 3-2: Limits — Limits for harmonic current
emissions (equipment input current ≤ 16 A per phase)
EN 61000-3-3:
2008
Electromagnetic compatibility (EMC) — Part 3-3: Limits — Limitation of voltage
changes, voltage fluctuations and flicker in public low voltage supply systems, for
equipment with rated current ≤ 16 A per phase and not subjected to conditional
connection
EN 61547:
2009
Equipment for general lighting purposes — EMC immunity requirements
The conformity of the designated product(s) with the provisions of the European Directive
1999/5/EC is given by the compliance with the following European Standard(s). If not
elsewhere/otherwise indicated the edition/amendment as referenced below applies.
ETSI EN 300
220-1 V2.1.1:
Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range
Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency
range with power levels ranging up to 500 mW; Part 1: Technical characteristics and
test methods
ETSI EN 300
220-2 V2.1.2:
Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range
Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency
range with power levels ranging up to 500 mW; Part 2: Harmonized EN covering
essential requirements under article 3.2 of the R&TTE Directive
ETSI EN 301
489-1 V1.8.1
Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro Magnetic
Compatibility (EMC) standard for radio equipment and services; Part 1: Common
technical requirements
ETSI EN 301
489-3 V1.4.1
Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro Magnetic
Compatibility (EMC) standard for radio equipment and services; Part 3: Specific
conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz
and 40 GHz
3/5
Form_EC_120430
EC-Declaration of Conformity
Annex
Document number: 2012 / QTP8_03
The conformity of the designated product(s) with the provisions of the European Directive
2009/125/EC is given by the compliance with the following European Standard(s). If not
elsewhere/otherwise indicated the edition/amendment as referenced below applies.
EN 50294:
1998 + A1:2001
+ A2:2003
Measurement method of total input power of ballast-lamp circuits
EN 62442-1:
2011
Energy performance of lamp controlgear - Part 1: Controlgear for fluorescent lamps Method of measurement to determine the total input power of controlgear circuits and
the efficiency of the controlgear
4/5
Form_EC_120430
EC-Declaration of Conformity
Attached list
Document number: 2012 / QTP8_03
QTP8 1x18
QTP8 1x36
QTP8 1x58
QTP8 2x18
QTP8 2x36
QTP8 2x58
QTP8 3x18,4x18
5/5
Form_EC_120430