P10AU

P10AU-xxxxELF
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
PME-SERIES
Rev.03-2013
2 Watt
Unregulated
Single Output
SIP4 Case
1 kV DC I/O Isolation
Low Ripple and Noise
The PME series P10AU-xxxxELF is a family of cost effective 2 W single
output DC/DC converters. These converters are in an ultra miniature SIP4
case. Devices are encapsulated. High performance features: 1000VDC
input/output isolation, high efficiency operation, output voltage accuracy of
±3% maximum, input range of ±10% tolerance and low output ripple and
noise.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Reflected Ripple Current¹
± 10%
Capacitors
20 mA pk-pk
Output Specifications
Voltage Accuracy
Short Circuit Protection
Line Regulation
Load Regulation (20% - 100%)
Ripple and Noise (20Mhz bandwidth)
Temperature Coefficient
± 3%
Short Term
± 1.2% / 1% Vin Change
± 10% (3.3Vout: ± 20% / 13Vout: ± 8% )
150 mV pk-pk
± 0.02% / °C
General Specifications
Efficiency
I/O Isolation Voltage (3 sec.)
I/O Isolation Capacity
I/O Isolation Resistance
Switching Frequency
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
See Table
1000 VDC
60 pF, typ.
1000 MOhm
70 kHz (Variable)
95% rel H
> 1.121 Mhrs
Physical Specifications
Case Material
Potting Material
Weight
Non Conductive Black Plastic (UL94V-0 rated)
Epoxy (UL94V-0 rated)
~ 1.8g, typ.
Environment Specifications
Operating Temperature
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +85°C (ambient)
100°C
-40 to +125°C
Free Air Convection
Soldering 260°C, max. (1.5mm from case 10s.)
PME-Series – P10AU-xxxxELF – Single Output – SIP4 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/3
Selection Guide
Single Output
A)
)
A)
d (m
(mA ad (m
a
)
o
d
L
a
C
)
o
ll
F)²
(VD
o Lo t Full L
VDC
t Fu
d (u
(
N
e
n
)
a
t
g
e
e
o
n
n
a
r
%
t
rre
rre
ltag
or L
Cur
cy (
Vol
t Vo
t Cu put Cu
acit
put
put
cien
Inpu
Inpu
In
Out
Out
Effi
Cap
Order #
SINGLE OUTPUT
P10AU-053R3ELF
P10AU-0505ELF
P10AU-057R2ELF
P10AU-0509ELF
P10AU-0512ELF
P10AU-0515ELF
P10AU-0518ELF
P10AU-0524ELF
P10AU-123R3ELF
P10AU-1205ELF
P10AU-127R2ELF
P10AU-1209ELF
P10AU-1212ELF
P10AU-1215ELF
P10AU-1218ELF
P10AU-1224ELF
P10AU-153R3ELF
P10AU-1505ELF
P10AU-157R2ELF
P10AU-1509ELF
P10AU-1512ELF
P10AU-1515ELF
P10AU-1518ELF
P10AU-1524ELF
P10AU-243R3ELF
P10AU-2405ELF
P10AU-247R2ELF
P10AU-2409ELF
P10AU-2412ELF
P10AU-2413ELF
P10AU-2415ELF
P10AU-2418ELF
P10AU-2424ELF
P10AU-483R3ELF
P10AU-4805ELF
P10AU-487R2ELF
P10AU-4809ELF
P10AU-4812ELF
P10AU-4815ELF
P10AU-4818ELF
P10AU-4824ELF
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
15
15
15
15
15
15
15
15
24
24
24
24
24
24
24
24
24
48
48
48
48
48
48
48
48
35
35
35
35
35
35
35
35
20
20
20
20
20
20
20
25
18
18
18
18
18
18
18
18
10
10
10
10
10
12
10
10
10
7
7
7
7
7
7
7
7
371
519
519
500
487
487
487
487
152
213
208
203
198
198
198
203
120
170
166
162
158
158
158
162
74
104
104
99
99
104.16
99
99
99
38
53
52
51
52
51
51
51
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
13
15
18
24
3.3
5
7.2
9
12
15
18
24
400
400
278
222
167
133
111
83
400
400
278
222
167
133
111
83
400
400
278
222
167
133
111
83
400
400
278
222
167
153.84
133
111
83
400
400
278
222
167
133
111
83
71
77
77
80
82
82
82
82
72
78
80
82
84
84
84
82
73
78
80
82
84
84
84
82
74
80
80
84
84
80
84
84
84
72
78
80
82
80
82
82
82
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
470
If you need other specifications, please enquire.
PME-Series – P10AU-xxxxELF – Single Output – SIP4 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/3
2.00
(0.08)
Package / Pinning / Derating
0.25
(0.01)
0.50
(0.02)
1
2
3
4
All dimensions are typical in millimeters (inches).
- Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002)
- Pin pitch tolerance: +/-0.35 (+/-0.014)
- Case tolerance +/-0.5 (+/-0.02)
Specification may change without notice.
Bottom View
0.50
(0.02)
7.50
(0.29)
PEAK
Modelcode
3.05
(0.12)
9.65
(0.38)
11.68
(0.46)
Datecode
2
3
4
0.50
(0.02)
1
2.54
(0.10)
0.50
(0.02)
SIP4 – PLASTIC CASE
PIN CONNECTIONS
#
SINGLE
1 - Vin
2 +Vin
3 - Vout
4 +Vout
App Notes:
¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH.
² = Tested by minimal Vin and constant resistive load.
- Operation under no-load conditions will not damage these devices, but they will not observe the listed specifications.
- For reduce converter’s ripple & noise, it is recommended to add a 4.7µF~220µF capacitor in output end. For EMI performance
improvement, it is recommended to add a 12µH inductor and a 10µF~100µF capacitor in input end.
Radiated
Emissions
EMC SPECIFICATIONS
EN 55022
FCC 47CFR Part 15/B
ESD
IEC 61000-4-2
RS
IEC 61000-4-3
CLASS B
CLASS B
Perf. Criteria B
Perf.Criteria A (at P10AU-2413ELF)
Perf. Criteria A
PME-Series – P10AU-xxxxELF – Single Output – SIP4 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/3