PEA2-xxxxE/Z (H30) LF PMM1-SERIES Rev.05-2011 2 Watt Semi Regulated Single and Dual Output SIP7 Case 1 - 3 kV DC I/O Isolation Low Ripple and Noise High Efiiciency Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PMM1 series PEA2-xxxxE/Z(H30)LF is a family of cost effective 2 W single & dual output DC-DC converters. These converters are in an ultra miniature SIP7 case. Devices are encapsulated. High performance features: 1000 – 3000 VDC input/output isolation, high efficiency operation, output voltage accuracy of ±3% maximum, input range of ±10% tolerance and low output ripple and noise. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ ± 10% Capacitor 25 mA (5, 12V) 30mA (15V) 40mA (24V) p-p Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Load Regulation (10% - 100%) Ripple and Noise (20Mhz bandwidth) Temperature Coefficient +2% ~ -4% Short Term ± 1.2% / 1% Vin Change See table 50 mV pk-pk ± 0.02% / °C General Specifications Efficiency I/O Isolation Voltage (3 sec.) I/O Isolation Capacity I/O Isolation Resistance Switching Frequency Humidity Reliability Calculated MTBF (MIL-HDBK-217F) See Table 1000 VDC (3000VDC optional)* 60 pF, typ. 1G Ohm 70 kHz (Variable) 95% rel H > 1.9 Mhrs Physical Specifications Case Material Potting Material Weight Non Conductive Black Plastic (UL94V-0 rated) Epoxy (UL94V-0 rated) ~ 2.8g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +85°C (ambient) 100°C -40 to +125°C Free Air Convection (10 mm distance required) Soldering 260°C, max. (1.5 mm from case 10s.) PMM1-Series – PEA2-xxxxE/Z (H30) LF – Single and Dual Output – SIP7 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide Single / Dual Output A) ) A) d (m (mA ad (m a ) d o a L ) C ) ll Lo F)² C Lo (VD n (% t Fu d (u (VD o No e Full i n ) t a g t t e e a o a n n l r % g t rre rre y( lta or L Vol Cur egu t Vo t Cu put Cu ienc acit dR put put Inpu Inpu In Out Out Loa Effic Cap Order # SINGLE OUTPUT PEA2-0505ELF PEA2-0509ELF PEA2-0512ELF PEA2-0515ELF PEA2-1205ELF PEA2-1209ELF PEA2-1212ELF PEA2-1215ELF PEA2-1505ELF PEA2-1509ELF PEA2-1512ELF PEA2-1515ELF PEA2-2405ELF PEA2-2409ELF PEA2-2412ELF PEA2-2415ELF 5 5 5 5 12 12 12 12 15 15 15 15 24 24 24 24 50 50 50 50 40 40 40 40 30 30 30 30 20 20 20 20 494 471 471 465 198 194 189 189 157 153 153 152 102 99 97 96 5 9 12 15 5 9 12 15 5 9 12 15 5 9 12 15 400 222 166 133 400 222 166 133 400 222 166 133 400 222 166 133 6 4.2 3.8 4.5 4.2 2.8 2.4 2.2 4 2.6 2.4 2 4.5 3.5 3 2.8 81 85 85 86 84 86 88 88 85 87 87 88 82 84 86 87 220 220 100 100 220 220 100 100 220 220 100 100 220 220 100 100 DUAL OUTPUT PEA2-0505ZLF PEA2-0509ZLF PEA2-0512ZLF PEA2-0515ZLF PEA2-1205ZLF PEA2-1209ZLF PEA2-1212ZLF PEA2-1215ZLF PEA2-1505ZLF PEA2-1509ZLF PEA2-1512ZLF PEA2-1515ZLF PEA2-2405ZLF PEA2-2409ZLF PEA2-2412ZLF PEA2-2415ZLF 5 5 5 5 12 12 12 12 15 15 15 15 24 24 24 24 50 50 50 50 40 40 40 40 30 30 30 30 20 20 20 20 488 471 465 460 200 189 187 187 157 152 152 152 102 98 97 96 ±5 ±9 ± 12 ± 15 ±5 ±9 ± 12 ± 15 ±5 ±9 ± 12 ± 15 ±5 ±9 ± 12 ± 15 ± 200 ± 111 ± 41.67 ± 66 ± 200 ± 111 ± 41.67 ± 66 ± 200 ± 111 ± 41.67 ± 66 ± 200 ± 111 ± 41.67 ± 66 5 3.9 3.7 4 3.4 2.4 2.2 1.9 3.4 2.4 2.2 1.9 3.5 2.4 2.2 1.9 82 85 86 87 84 88 89 89 85 88 88 88 82 85 86 87 ± 100 ± 100 ± 47 ± 47 ± 100 ± 100 ± 47 ± 47 ± 100 ± 100 ± 47 ± 47 ± 100 ± 100 ± 47 ± 47 * For optional 3kV Isolation please add “H30” between E/Z and LF! Example: PEA2-2415EH30LF for 3kV isolation. PMM1-Series – PEA2-xxxxE/Z (H30) LF – Single and Dual Output – SIP7 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 Package / Pinning / Derating # 1 2 4 5 6 7 SINGLE +Vin - Vin - Vout Omitted +Vout Omitted PIN CONNECTIONS DUAL SINGLE 3kV +Vin +Vin - Vin - Vin - Vout Omitted Common - Vout +Vout Omitted Omitted +Vout DUAL 3kV +Vin - Vin Omitted - Vout Common +Vout App Notes: ¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH. ² = Tested by minimal Vin and constant resistive load. - Operation under no-load conditions will not damage these devices, but they will not observe the listed specifications. * For optional 3kV Isolation please add “H30” between E/Z and LF! Example: PEA2-2415EH30LF for 3kV isolation. Radiated Emissions Conducted Emissions ** ESD RS EFT*** CS PFMF EMC SPECIFICATIONS EN 55022 CLASS B EN55022 CLASS B EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-6 EN 61000-4-8 Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A PEA2-05xxXLF PEA2-12xxXLF PEA2-15xxXLF PEA2-24xxXLF ** Input filter components (C1, C2, C3, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; all leads should be minimized to decrease radiated noise. *** An external filter capacitor is required if the module has to meet EN61000-4-4. (e.g. Nippon chemi-con KY series, 220uF/100V C1 L 1210, 2.2uF/100V 1210, 2.2uF/100V 1210, 2.2uF/100V 1210, 2.2uF/100V 18 uH 18 uH 18 uH 18 uH C2 C3 1210, 2.2uF/100V 1206, 470pF/2kV PMM1-Series – PEA2-xxxxE/Z (H30) LF – Single and Dual Output – SIP7 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3