P40XG-xxxxE/Z4:1LF PMM40A-SERIES Rev.02-2011 40 Watt 4:1 Wide Input 2” x 2” Case 1.6 kV DC I/O Isolation Regulated Output Single and Dual Output Continuous SC / OV / OC Prot. Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PMM40A series is a family of cost effective 40W single & dual output DC-DC converters. These converters combine nickle-coated copper package in a 2"x2" case with high performance features such as Active Clamp Technology, continuous short circuit protection with automatic restart and tight line / load regulation. Devices are encapsulated using flame retardant resin. Input voltages of 24 and 48 with output voltage of 3.3, 5, 12, 15, ±12, ±15Vdc. High performance features include high efficiency operation up to 92% and output voltage accuracy of ±1% maximum. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current ¹ Start up Time (Nom. Vin and constant resistive load) 4:1 Wide Input (See Table) Pi Type 20 mA pk-pk 25mS Output Specifications Voltage Accuracy / Adjustability (TRIM) ² Short Circuit Protection Over Load Protection Line Regulation Load Regulation (1% - 100%) Cross Regulation3 (Dual Out) Ripple and Noise4 (20Mhz bandwidth) Temperature Coefficient Transient Recovery Time / Response Dev.5 ± 1% / ± 10%, max. Indefinite (hiccup / Automatic Recovery) 130% of FL ± 0.5%, max. ± 0.5%, max.(Single out) ± 1%, max.(Dual out) ± 5% 75mV(Single) 150 mV(Dual) pk-pk, max. ± 0.02% / °C 250µs. / ± 3%, max. General Specifications I/O Isolation Voltage (3 sec.) I/O Isolation Capacitance I/O Isolation Resistance Switching Frequency Humidity Reliability Calculated MTBF (MIL-HDBK-217F) Safety Standart (Design to meet) 1600 VDC 2500 pF, max. 1000 M Ohm, min. 270 kHz 95% rel H > 151 khrs IEC/EN 60950-1 Physical Specifications Case Material Potting Material Weight Nickel Coated Copper Epoxy (UL94V-0 rated) ~ 60g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +55°C (ambient, for 100% load) 105°C -40 to +125°C Free Air Convection (10mm distance required) Soldering 260°C, max. (1.5mm from case 10s.) PMM40A-Series – P40XG-xxxxE/Z4:1LF – Single and Dual Output – 2”x 2” - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide ) ) m A) m A) (mA ad (mA ad ( ad ( o ) d o 6 L a L C ) o . l C in Lo ul u F) ll L VD (V D nt M nt F ) ad ( t No rent Fu ge ( e e e o n a r r % g t r r L ( l e a r r r y lt or Cu Cu Vo t Cu p u t Cu t Vo ienc acit put put put Inpu Inpu In Out Ou t Out Effic Cap Order # SINGLE OUTPUT P40XG-243R3E4:1LF P40XG-2405E4:1LF P40XG-2412E4:1LF P40XG-2415E4:1LF P40XG-483R3E4:1LF P40XG-4805E4:1LF P40XG-4812E4:1LF P40XG-4815E4:1LF 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 80 100 50 50 60 60 30 30 1598 1893 1925 1904 799 936 963 941 3.3 5 12 15 3.3 5 12 15 0 0 0 0 0 0 0 0 10000 8000 3350 2650 10000 8000 3350 2650 89 91 90 90 89 92 90 91 25000 13000 2300 1500 25000 13000 2300 1500 DUAL OUTPUT P40XG-2412Z4:1LF P40XG-2415Z4:1LF P40XG-4812Z4:1LF P40XG-4815Z4:1LF 9-36 9-36 18-75 18-75 60 60 30 30 1919 1962 948 970 ± 12 ± 15 ± 12 ± 15 0 0 0 0 ± 1650 ± 1350 ± 1650 ± 1350 89 89 90 90 ± 1200 ± 750 ± 1200 ± 750 If you need other specifications, please enquire. Package / Pinning / Derating # 1 2 3 4 5 6 7 8 PIN CONNECTIONS SINGLE DUAL +Vin +Vin - Vin - Vin CTRL CTRL - Sense +Vout +Sense Common +Vout Common - Vout - Vout TRIM TRIM PMM40A-Series – P40XG-xxxxE/Z4:1LF – Single and Dual Output – 2”x 2” - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 App Notes 1. Measured Input reflected ripple current with a simulated source inductance of 12uH. 2. For the Single output: Maximum output deviation is 10% inclusive of remote sense and trim. If remote sense is not being used, the +sense should be connected to its corresponding +OUTPUT and likewise the -sense should be connected to its corresponding -OUTPUT. 3. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 4. Measured with 20MHz bandwidth and 1.0uF ceramic capacitor. 5. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 6. Tested by minimal Vin and constant resistive load. 7. The PMM40A series can meet EN55022 Class A With an external filter in parallel with the input pins . 8. An external filter capacitor is required if the module has to meet EN61000-4-4 and EN61000-4-5. The filter capacitor Peak suggest: Nippon chemi-con KY series, 220uF/100V 9. The remote on/off control pin is referenced to -Vin(pin2). EMC SPECIFICATIONS Radiated Emissions EN 55022 7 EN 55022 Conducted Emissions ESD IEC 61000-4-2 RS IEC 61000-4-3 8 IEC 61000-4-4 EFT 8 Surge CS PFMF CLASS A CLASS A Perf. Criteria A Perf. Criteria A Perf. Criteria A IEC 61000-4-5 IEC 61000-4-6 IEC 61000-4-8 Perf. Criteria A Perf. Criteria A Perf. Criteria A Under Input Voltage Lockout (typ.) 24 Vin Models Module ON/OFF 8.6V / 7.9V 48 Vin Models Module ON/OFF 17.8V / 16V Over Voltage Protection (Zender Diode Clamp) 3.3 Vout 3.9 V 5 Vout 6.2 V 12 Vout 15 V 15 Vout 18 V ± 12 Vout ± 15 V ± 15 Vout ± 18 V External Output Trimming Output can be externally trimmed by using the method as below. (..) = for Dual Output 9 Remote ON/OFF Control ON: 3 -12 VDC or open circuit 0 – 1.2 VDC or short circuit OFF: PIN2 and PIN3 OFF idle current: 5mA, typ. Notes: PMM40A-Series – P40XG-xxxxE/Z4:1LF – Single and Dual Output – 2”x 2” - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3