PEA3

PEA3-xxxxE/Z (H30) LF
PMM1-SERIES
Rev.09-2010
3 Watt
Semi Regulated
Single and Dual Output
SIP7 Case
1 - 3 kV DC I/O Isolation
Low Ripple and Noise
High Efiiciency
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
The PMM1 series PEA3-xxxxE/Z(H30)LF is a family of cost effective 3 W
single & dual output DC-DC converters. These converters are in an ultra
miniature SIP7 case. Devices are encapsulated. High performance
features: 1000 – 3000 VDC input/output isolation, high efficiency operation,
output voltage accuracy of ±3% maximum, input range of ±10% tolerance
and low output ripple and noise.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Reflected Ripple Current
± 10%
Capacitor
20 mA pk-pk
Output Specifications
Voltage Accuracy
Short Circuit Protection
Line Regulation
Load Regulation (10% - 100%)
Ripple and Noise (20Mhz bandwidth)
Temperature Coefficient
± 3%
Short Term
± 1.2% / 1% Vin Change
See table
50 mV pk-pk
± 0.02% / °C
General Specifications
Efficiency
I/O Isolation Voltage (3 sec.)
I/O Isolation Capacity
I/O Isolation Resistance
Switching Frequency
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
See Table
1000 VDC (3000VDC optional)*
60 pF, typ.
1G Ohm
70 kHz (Variable)
95% rel H
> 1.8 Mhrs
Physical Specifications
Case Material
Potting Material
Weight
Non Conductive Black Plastic (UL94V-0 rated)
Epoxy (UL94V-0 rated)
~ 2.8g, typ.
Environment Specifications
Operating Temperature (ambient)
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +85°C (12 Vin) -40 to +71°C (5 Vin)
100°C
-40 to +125°C
Free Air Convection (10 mm distance required)
Soldering 260°C, max. (1.5 mm from case 10s.)
PMM1-Series – PEA3-xxxxE/Z (H30) LF – Single and Dual Output – SIP7 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/3
Selection Guide
Single / Dual Output
)
)
A)
mA
(mA ad (m
ad (
)
d
o
a
L
C
)
o
ll
L
D
F)¹
C
%)
Lo
t Fu
d (u
(VD
on (
e (V
No
Full
i
n
)
t
a
g
t
t
e
e
a
o
a
n
n
l
r
%
g
t
rre
rre
y(
lta
or L
Vol
Cur
egu
t Vo
t Cu put Cu
ienc
acit
dR
put
put
Inpu
Inpu
In
Out
Out
Loa
Effic
Cap
Order #
SINGLE OUTPUT
PEA3-0505ELF
PEA3-0509ELF
PEA3-0512ELF
PEA3-0515ELF
PEA3-1205ELF
PEA3-1209ELF
PEA3-1212ELF
PEA3-1215ELF
5
5
5
5
12
12
12
12
80
80
80
80
20
20
20
20
730
730
725
725
294
294
274
274
5
9
12
15
5
9
12
15
600
333
250
200
600
333
250
200
8
7
7
6
5
4
4
3
80
81
82
84
84
86
89
90
220
220
100
100
220
220
100
100
DUAL OUTPUT
PEA3-0505ZLF
PEA3-0509ZLF
PEA3-0512ZLF
PEA3-0515ZLF
PEA3-1205ZLF
PEA3-1209ZLF
PEA3-1212ZLF
PEA3-1215ZLF
5
5
5
5
12
12
12
12
70
70
70
70
20
20
20
20
730
730
700
700
298
298
274
274
±5
±9
± 12
± 15
±5
±9
± 12
± 15
± 300
± 166,67
± 125
± 100
± 300
± 166,67
± 125
± 100
7
6
6
5
4
3.5
3.5
3
82
83
84
86
85
86
89
90
± 100
± 100
± 47
± 47
± 100
± 100
± 47
± 47
* For optional 3kV Isolation please add “H30” between E/Z and LF!
Example: PEA3-1215EH30LF for 3kV isolation.
PMM1-Series – PEA3-xxxxE/Z (H30) LF – Single and Dual Output – SIP7 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/3
Package / Pinning / Derating
2.1
(0.9)
All dimensions are typical in millimeters (inches).
- Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002)
- Pin pitch tolerance: +/-0.35 (+/-0.014)
- Case tolerance +/-0.5 (+/-0.02)
Specification may change without notice.
0.50
(0.02)
0.50
(0.02)
7.20
(0.28)
19.50
(0.76)
PEAK
Modelcode
Datecode
1
2.54
(0.10)
2
4
5
6
7
SIP 7 – PLASTIC CASE
15.24
(0.60)
#
1
2
4
5
6
7
SINGLE
+Vin
- Vin
- Vout
Omitted
+Vout
Omitted
PIN CONNECTIONS
DUAL SINGLE 3kV
+Vin
+Vin
- Vin
- Vin
- Vout
Omitted
Common - Vout
+Vout
Omitted
Omitted +Vout
DUAL 3kV
+Vin
- Vin
Omitted
- Vout
Common
+Vout
App Notes:
¹ = Tested by minimal Vin and constant resistive load.
- Operation under no-load conditions will not damage these devices, but they will not observe the listed specifications.
* For optional 3kV Isolation please add “H30” between E/Z and LF! Example: PEA3-1215EH30LF for 3kV isolation.
Radiated Emissions
ESD
RS
EMC SPECIFICATIONS
EN 55022
IEC 61000-4-2
IEC 61000-4-3
CLASS B
Perf. Criteria A
Perf. Criteria A
Input filter components (C1, L) are used to help meet conducted emissions requirement for the module.
These components should be mounted as close as possible to the module; all leads should be minimized to decrease radiated
noise.
PEA3-05xxXLF
PEA3-12xxXLF
C1
L
1210, 2.2uF/100V
1210, 2.2uF/100V
18 uH
18 uH
PMM1-Series – PEA3-xxxxE/Z (H30) LF – Single and Dual Output – SIP7 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/3