P6MU-xxxxE/Z(Hxx)LF - PEAK electronics GmbH

P6MU-xxxxE/Z(Hxx)LF
PM1-SERIES
Rev.11-2008
1 Watt
Unregulated
Single and Dual Output
DIP14 Case
3 - 6 kV DC I/O Isolation
Low Ripple and Noise
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
The PM1 series P6MU-xxxxE/Z(Hxx)LF is a family of cost effective 1 W
single & dual output DC-DC converters. These converters are in an ultra
miniature DIP14 case. Devices are encapsulated. High performance
features: 3000VDC up to 6000VDC input/output isolation, high efficiency
operation, output voltage accuracy of ±3% maximum, input range of ±10%
tolerance and low output ripple and noise.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Reflected Ripple Current¹
± 10%
Capacitor
20 mA pk-pk
Output Specifications
Voltage Accuracy
Short Circuit Protection
Line Regulation
Load Regulation (20% - 100%)
Ripple and Noise (20Mhz bandwidth)
Temperature Coefficient
± 3%
Short Term
± 1.2% / 1% Vin Change
± 10% (3.3 Vout Models: ± 20%)
75 mV pk-pk
± 0.02% / °C
General Specifications
Efficiency
I/O Isolation Voltage (3 sec.)
I/O Isolation Capacity
I/O Isolation Resistance
Switching Frequency
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
See table
3000 VDC (up to 6000 VDC optional)*
60 pF, typ.
1000 M Ohm
80 kHz (Variable)
95% rel H
>1.121 Mhrs
Physical Specifications
Case Material
Potting Material
Weight
Non Conductive Black Plastic (UL94V-0 rated)
Epoxy (UL94V-0 rated)
~ 2.6g, typ.
Environment Specifications
Operating Temperature
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +85 °C (ambient)
100°C
-40 to +125°C
Free Air Convection
Soldering 260°C, max. (1.5mm from case 10s.)
PM1-Series – P6MU-xxxxE/Z(Hxx)LF – Single and Dual Output – DIP14 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/4
Selection Guide
Single Output
)
)
m A)
(mA ad (mA
ad (
)
d
o
a
L
C
)
o
L
F)²
D
C
Lo
ull
d (u
(VD
No
e (V
Full
)
nt F
a
t
t
g
e
e
o
n
n
a
%
r
g
t
(
r
L
l
e
e
y
rr
rr
lta
or
Cu
Vo
t Cu put Cu
t Vo
ienc
acit
put
put
In p u
In p u
In
O ut
O ut
E ffic
Cap
Order #
SINGLE OUTPUT
P6MU-053R3ELF
P6MU-0505ELF
P6MU-057R2ELF
P6MU-0509ELF
P6MU-0512ELF
P6MU-0515ELF
P6MU-0518ELF
P6MU-0524ELF
P6MU-123R3ELF
P6MU-1205ELF
P6MU-127R2ELF
P6MU-1209ELF
P6MU-1212ELF
P6MU-1215ELF
P6MU-1218ELF
P6MU-1224ELF
P6MU-243R3ELF
P6MU-2405ELF
P6MU-247R2ELF
P6MU-2409ELF
P6MU-2412ELF
P6MU-2415ELF
P6MU-2418ELF
P6MU-2424ELF
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
30
30
30
30
30
30
30
30
20
20
20
20
20
20
20
20
10
10
10
10
10
10
10
10
267
256
267
267
263
263
267
278
113
113
113
111
108
106
106
111
56
54
56
56
53
53
53
53
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
303
200
138.9
111.1
83.3
66.7
55.6
41.7
303
200
138.9
111.1
83.3
66.7
55.6
41.7
303
200
138.9
111.1
83.3
66.7
55.6
41.7
75
78
75
75
76
76
75
72
74
74
74
75
77
78
78
75
75
77
75
75
78
78
78
78
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
If you need other specifications, please enquire.
*OPTIONS:
H40 = 4000 VDC ISOLATION
H52 = 5200 VDC ISOLATION
H60 = 6000 VDC ISOLATION
For other I/O Isolation please see
table on the left hand side and add
“Hxx” before LF
(P6MU-2412EH60LF for 6KV)
PM1-Series – P6MU-xxxxE/Z(Hxx)LF – Single and Dual Output – DIP14 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/4
Selection Guide
Dual Output
A)
m A)
A)
ad (
)
o
d (m Load (m
L
a
C
l
o
L
ul
uF)²
ll
VD
(V
)
nt F
ad (
ge (
t N o re n t F u
e
e
o
a
n
%
r
g
t
(
L
r
l
e
a
r
y
r
r
lt
or
Cu
Vo
ienc
t Cu put Cu
t Vo
acit
put
put
In p u
In p u
In
O ut
O ut
E ffic
Cap
dc)
Order #
DUAL OUTPUT
P6MU-053R3ZLF
P6MU-0505ZLF
P6MU-057R2ZLF
P6MU-0509ZLF
P6MU-0512ZLF
P6MU-0515ZLF
P6MU-0518ZLF
P6MU-0524ZLF
P6MU-123R3ZLF
P6MU-1205ZLF
P6MU-127R2ZLF
P6MU-1209ZLF
P6MU-1212ZLF
P6MU-1215ZLF
P6MU-1218ZLF
P6MU-1224ZLF
P6MU-243R3ZLF
P6MU-2405ZLF
P6MU-247R2ZLF
P6MU-2409ZLF
P6MU-2412ZLF
P6MU-2415ZLF
P6MU-2418ZLF
P6MU-2424ZLF
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
30
30
30
30
30
30
30
30
20
20
20
20
20
20
20
20
10
10
10
10
10
10
10
10
307
270
259
256
256
250
256
266
126
111
115
111
106
106
111
111
62
57
59
55
53
55
57
59
± 3.3
±5
± 7.2
±9
± 12
± 15
± 18
± 24
± 3.3
±5
± 7.2
±9
± 12
± 15
± 18
± 24
± 3.3
±5
± 7.2
±9
± 12
± 15
± 18
± 24
± 151.5
± 100
± 69.44
± 55.55
± 41.67
± 33.33
± 27.77
± 20.83
± 151.5
± 100
± 69.44
± 55.55
± 41.67
± 33.33
± 27.77
± 20.83
± 151.5
± 100
± 69.44
± 55.55
± 41.67
± 33.33
± 27.77
± 20.83
65
74
77
78
78
80
78
75
66
75
72
75
78
78
75
75
67
72
70
75
78
75
72
70
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
If you need other specifications, please enquire.
*OPTIONS:
H40 = 4000 VDC ISOLATION
H52 = 5200 VDC ISOLATION
H60 = 6000 VDC ISOLATION
For other I/O Isolation please see
table on the left hand side and add
“Hxx” before LF
(P6MU-2412ZH60LF for 6KV)
PM1-Series – P6MU-xxxxE/Z(Hxx)LF – Single and Dual Output – DIP14 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/4
10.16
(0.40)
7.62
(0.30)
0.25
(0.01)
Package / Pinning / Derating
#
1
7
8
9
10
11
14
PIN CONNECTIONS
SINGLE ≥3KV DUAL ≥3KV
- Vin
- Vin
N.C.
N.C.
+Vout
+Vout
Omitted
Common
- Vout
- Vout
Omitted
Omitted
+Vin
+Vin
App Notes:
¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH.
² = Tested by minimal Vin and constant resistive load.
- Operation under no-load conditions will not damage these devices, but they will not observe the listed specifications.
- For reduce converter’s ripple & noise, it is recommended to add a 4.7µF~100µF(±4.7µF~±68µF for dual output) capacitor in
output end. For EMI performance improvement, it is recommended to add a 12µH inductor and a 10µF~100µF capacitor in input
end.
PM1-Series – P6MU-xxxxE/Z(Hxx)LF – Single and Dual Output – DIP14 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 4/4