P3MU-xxxxE/Z(Hxx)LF PM1-SERIES Rev.11-2008 0.5 Watt Unregulated Single and Dual Output DIP14 Case 3 - 6 kV DC I/O Isolation* Low Ripple and Noise Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PM1 series P3MU-xxxxE/Z(H30)LF is a family of cost effective 0.5 W single & dual output DC-DC converters. These converters are in an ultra miniature DIP14 case. Devices are encapsulated. High performance features: 3000VDC up to 6000VDC input/output isolation, high efficiency operation, output voltage accuracy of ±3% maximum, input range of ±10% tolerance and low output ripple and noise. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ ± 10% Capacitor 20 mA pk-pk Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Load Regulation (20% - 100%) Ripple and Noise (20Mhz bandwidth) Temperature Coefficient ± 3% Short Term ± 1.2% / 1% Vin Change ± 10% (3.3Vout Models: ± 20%) 75 mV pk-pk ± 0.02% / °C General Specifications Efficiency I/O Isolation Voltage (3 sec.) I/O Isolation Capacity I/O Isolation Resistance Switching Frequency Humidity Reliability Calculated MTBF (MIL-HDBK-217F) See Table 3000 VDC (up to 6000 VDC optional)* 60 pF, typ. 1000 MOhm 80 kHz (Variable) 95% rel H > 1.121 Mhrs Physical Specifications Case Material Potting Material Weight Non Conductive Black Plastic (UL94V-0 rated) Epoxy (UL94V-0 rated) ~ 2.6g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +85°C (ambient) 100°C -40 to +125°C Free Air Convection Soldering 260°C, max. (1.5mm from case 10s.) PM1-Series – P3MU-xxxxE/Z(Hxx)LF – Single and Dual Output – DIP14 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/4 Selection Guide Single Output ) ) mA) (mA ad (mA ad ( ) d o a L C ) o L F)² D C Lo ull d (u (VD No F u ll e (V ) nt F a t t g e e o n n a % r g t ( L r l e e rr rr y lta or Vo Cu ienc t Vo t Cu put Cu acit put put In p u In p u In O ut O ut Effic Cap Order # SINGLE OUTPUT P3MU-053R3ELF P3MU-0505ELF P3MU-057R2ELF P3MU-0509ELF P3MU-0512ELF P3MU-0515ELF P3MU-0518ELF P3MU-0524ELF P3MU-123R3ELF P3MU-1205ELF P3MU-127R2ELF P3MU-1209ELF P3MU-1212ELF P3MU-1215ELF P3MU-1218ELF P3MU-1224ELF P3MU-243R3ELF P3MU-2405ELF P3MU-247R2ELF P3MU-2409ELF P3MU-2412ELF P3MU-2415ELF P3MU-2418ELF P3MU-2424ELF 5 5 5 5 5 5 5 5 12 12 12 12 12 12 12 12 24 24 24 24 24 24 24 24 30 30 30 30 30 30 30 30 20 20 20 20 20 20 20 20 10 10 10 10 10 10 10 10 142 135 135 133 131 131 131 128 59 57 111 55 54 54 54 53 29 28 28 28 27 26 26 26 3.3 5 7.2 9 12 15 18 24 3.3 5 7.2 9 12 15 18 24 3.3 5 7.2 9 12 15 18 24 151.5 100 69.4 55.5 41.6 33.3 27.8 20.8 151.5 100 69.4 55.5 41.6 33.3 27.8 20.8 151.5 100 69.4 55.5 41.6 33.3 27.8 20.8 70 74 74 75 76 76 76 78 70 73 74 75 76 76 76 78 70 73 74 75 76 78 78 78 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 If you need other specifications, please enquire. *OPTIONS: H40 = 4000 VDC ISOLATION H52 = 5200 VDC ISOLATION H60 = 6000 VDC ISOLATION For other I/O Isolation please see table on the left hand side and add “Hxx” before LF (P3MU-2412EH60LF for 6KV) PM1-Series – P3MU-xxxxE/Z(Hxx)LF – Single and Dual Output – DIP14 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/4 Selection Guide Dual Output ) ) m A) (mA ad (mA ad ( ) d o a L C ) o L F)² D C Lo ull d (u (VD Full No e (V ) nt F a t g t e e o n a n % r g t ( L r l e e rr rr y l ta or Vo Cu t Vo ienc t Cu put Cu acit put put In p u In p u In O ut O ut E ffic Cap Order # DUAL OUTPUT P3MU-053R3ZLF P3MU-0505ZLF P3MU-057R2ZLF P3MU-0509ZLF P3MU-0512ZLF P3MU-0515ZLF P3MU-0518ZLF P3MU-0524ZLF P3MU-123R3ZLF P3MU-1205ZLF P3MU-127R2ZLF P3MU-1209ZLF P3MU-1212ZLF P3MU-1215ZLF P3MU-1218ZLF P3MU-1224ZLF P3MU-243R3ZLF P3MU-2405ZLF P3MU-247R2ZLF P3MU-2409ZLF P3MU-2412ZLF P3MU-2415ZLF P3MU-2418ZLF P3MU-2424ZLF 5 5 5 5 5 5 5 5 12 12 12 12 12 12 12 12 24 24 24 24 24 24 24 24 30 30 30 30 30 30 30 30 20 20 20 20 20 20 20 20 10 10 10 10 10 10 10 10 166 135 129 128 128 128 126 126 69 56 54 53 53 53 52 52 35 28 27 27 26 26 26 26 ± 3.3 ±5 ± 7.2 ±9 ± 12 ± 15 ± 18 ± 24 ± 3.3 ±5 ± 7.2 ±9 ± 12 ± 15 ± 18 ± 24 ± 3.3 ±5 ± 7.2 ±9 ± 12 ± 15 ± 18 ± 24 ± 75.7 ± 50 ± 34.7 ± 27.7 ± 20.8 ± 16.7 ± 13.9 ± 10.4 ± 75.7 ± 50 ± 34.7 ± 27.7 ± 20.8 ± 16.7 ± 13.9 ± 10.4 ± 75.7 ± 50 ± 34.7 ± 27.7 ± 20.8 ± 16.7 ± 13.9 ± 10.4 60 74 77 78 78 78 79 79 60 74 77 78 78 78 80 80 60 74 76 76 78 78 78 80 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 ± 100 If you need other specifications, please enquire. *OPTIONS: H40 = 4000 VDC ISOLATION H52 = 5200 VDC ISOLATION H60 = 6000 VDC ISOLATION For other I/O Isolation please see table on the left hand side and add “Hxx” before LF (P3MU-2412ZH40LF for 4KV) PM1-Series – P3MU-xxxxE/Z(Hxx)LF – Single and Dual Output – DIP14 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/4 10.16 (0.40) 7.62 (0.30) 0.25 (0.01) Package / Pinning / Derating # 1 7 8 9 10 11 14 PIN CONNECTIONS SINGLE ≥3KV DUAL ≥3KV - Vin - Vin N.C. N.C. +Vout +Vout Omitted Common - Vout - Vout Omitted Omitted +Vin +Vin App Notes: ¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH. ² = Tested by minimal Vin and constant resistive load. - Operation under no-load conditions will not damage these devices, but they will not observe the listed specifications. PM1-Series – P3MU-xxxxE/Z(Hxx)LF – Single and Dual Output – DIP14 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 4/4