P42WG_4:1

P42WG-xxxxE/Z4:1LF
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
PM7W-SERIES
Rev.10-2014
 10 Watt
 4:1 Ultra Wide Input
 2” x 1” Case
 1.5 kV DC I/O Isolation
 Regulated Output
 Single and Dual Output
 Continuous Short Circuit Prot.
The PM7W series P42WG-xxxxE/Z4:1LF is a family of cost effective 10 W,
single & dual output DC-DC converters with an ultra wide input range of
4:1. These converters are encapsulated in nickel coated brass 2”x1” case
with high performance features: 1500VDC input/output isolation voltage,
continuous short circuit protection with automatic restart and tight line / load
regulation, high efficiency operation and output voltage accuracy of ±1%
maximum.
 All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Reflected Ripple Current¹
Start up Time (Nom. Vin and constant resistive load)
4:1 Ultra Wide Input (See Table)
PI Type
35 mA pk-pk
20mS, typ.
Output Specifications
Voltage Accuracy
Short Circuit Protection
Over Current Protection
Line Regulation
Load Regulation (10% - 100%)
Cross Regulation (Dual Output)³
Ripple and Noise (20Mhz bandwidth)
Temperature Coefficient
± 1%
Indefinite (Automatic Recovery)
140% of max. Iout
± 0.5%
± 0.5% (10% - 100% load) ± 1.0% (< 10% load)
± 5%
75 mV pk-pk
± 0.02% / °C
General Specifications
Efficiency
I/O Isolation Voltage (3 sec.)
I/O Isolation Capacitance
I/O Isolation Resistance
Switching Frequency
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
See Table
1500 VDC
1200 pF, typ.
1000 M Ohm
300 kHz, typ.
95% rel H
> 1.121 Mhrs
Physical Specifications
Case Material
Potting Material
Weight
Nickel Coated Brass
Epoxy (UL94V-0 rated)
~ 30g, typ.
Environment Specifications
Operating Temperature
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +85°C (ambient)
100°C
-40 to +125°C
Free Air Convection
Soldering 260°C, max. (1.5mm from case 10s.)
PM7W-Series – P42WG-xxxxE/Z4:1LF – Single and Dual Output – 2”x1” - Metal Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/4
Selection Guide
Single and Dual Output
)
)
)
mA
(mA
A)
mA
d
(
m
a
(
ad (
d
o
)
d
o
a
L
a
L
C
)
o
.
ll
L
F)²
D
n
C
Lo
t Mi
t Fu
d (u
(VD
No
Full
e (V
n
n
)
a
g
t
t
e
e
e
o
n
n
a
r
r
%
g
t
rre
rre
lta
or L
Vol
Cur
Cur
cy (
t Vo
t Cu put Cu
acit
put
put
put
cien
Inpu
Inpu
In
Out
Out
Out
Effi
Cap
Order #
SINGLE OUTPUT
P42WG-243R3E4:1LF
P42WG-2405E4:1LF
P42WG-247R2E4:1LF
P42WG-2409E4:1LF
P42WG-2412E4:1LF
P42WG-2415E4:1LF
P42WG-2424E4:1LF
P42WG-483R3E4:1LF
P42WG-4805E4:1LF
P42WG-487R2E4:1LF
P42WG-4809E4:1LF
P42WG-4812E4:1LF
P42WG-4815E4:1LF
9-36
9-36
9-36
9-36
9-36
9-36
9-36
18-72
18-72
18-72
18-72
18-72
18-72
25
25
25
25
25
25
25
20
20
20
20
20
20
348
508
502
502
490
490
496
174
254
251
251
245
245
3.3
5
7.2
9
12
15
24
3.3
5
7.2
9
12
15
0
0
0
0
0
0
0
0
0
0
0
0
0
2000
2000
1388
1111
833
666
416
2000
2000
1388
1111
833
666
80
82
83
83
85
85
84
79
82
83
83
85
85
3300
3300
1000
680
680
470
330
3300
3300
1000
680
680
470
DUAL OUTPUT
P42WG-2405Z4:1LF
P42WG-247R2Z4:1LF
P42WG-2409Z4:1LF
P42WG-2412Z4:1LF
P42WG-2415Z4:1LF
P42WG-4805Z4:1LF
P42WG-487R2Z4:1LF
P42WG-4809Z4:1LF
P42WG-4812Z4:1LF
P42WG-4815Z4:1LF
9-36
9-36
9-36
9-36
9-36
18-72
18-72
18-72
18-72
18-72
25
25
25
25
25
20
20
20
20
20
508
502
502
490
490
254
251
251
245
245
±5
± 7.2
±9
± 12
± 15
±5
± 7.2
±9
± 12
± 15
0
0
0
0
0
0
0
0
0
0
± 1000
± 694
± 555
± 416
± 333
± 1000
± 694
± 555
± 416
± 333
82
83
83
85
85
82
83
83
85
85
± 2200
± 470
± 470
± 470
± 330
± 2200
± 470
± 470
± 470
± 330
If you need other specifications, please enquire.
Notes:
PM7W-Series – P42WG-xxxxE/Z4:1LF – Single and Dual Output – 2”x1” - Metal Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/4
Package / Pinning / Derating
10.16
(0.40)
DIA.
1.00
(0.04)
COM +Vout
(if Dual)
3
20.32
(0.80)
Modelcode
Datecode
Vin:
Vout:
Iout:
4
5
Bottom View
1
2
15.24
(0.60)
50.80
(2.00)
PEAK
Vin
-
10.16 10.16 2.54
(0.40) (0.40) (0.10)
15.24
(0.60)
-Vout
2.54
(0.10)
+
25.40
(1.00)
All dimensions are typical in millimeters (inches).
- Pin diameter: 1.0 +/-0.05 (0.04 +/-0.002)
- Pin pitch tolerance: +/-0.35 (+/-0.014)
- Case tolerance +/-0.5 (+/-0.02)
Specification may change without notice.
5.08
(0.20)
min.
10.16 5.08 10.16
(0.40) (0.20) (0.40)
2" x 1" – METAL CASE
OUTPUT POWER
TEMPERATURE DERATING GRAPH
100%
#
1
2
3
4
5
75%
50%
25%
PIN CONNECTIONS
SINGLE
DUAL
+Vin
+Vin
- Vin
- Vin
+Vout
+Vout
Omitted
Common
- Vout
- Vout
85
-40 -20
0
20
40
60
80 100
AMBIENT TEMPERATURE (°C)
PM7W-Series – P42WG-xxxxE/Z4:1LF – Single and Dual Output – 2”x1” - Metal Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/4
App Notes
Test Configurations
EMI Filter
Input Filter Components (C1, C2, L) are used to help meet conducted emissons requirement for the module.
These components should be mounted as close as possible ti the module; and all leads should be minimized to
decrease radiated noise.
EMC SPECIFICATIONS
Radiated Emissions
EN 55022
Conducted Emissions
EN 55022
ESD
IEC 61000-4-2
RS
IEC 61000-4-3
EFT
IEC 61000-4-4
IEC 61000-4-5
Surge4
CS
IEC 61000-4-6
PFMF
IEC 61000-4-8
CLASS A
CLASS A
Perf. Criteria B
Perf. Criteria A
Perf. Criteria A
Perf. Criteria A
Perf. Criteria A
Perf. Criteria A
App Notes:
¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH.
² = Tested by minimal Vin and constant resistive load.
³ = One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%.
4
= An external filter capacitor is required if the module has to meet IEC 61000-4-4 and IEC 61000-4-5.
PM7W-Series – P42WG-xxxxE/Z4:1LF – Single and Dual Output – 2”x1” - Metal Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 4/4