The following document contains information on Cypress products. FUJITSU SEMICONDUCTOR SUPPORT SYSTEM SS704-00001-1v0-E F2MC-16FX Family 16-BIT MICROCONTROLLER MB96610 series MB96610 Evaluation Board MB2198-761-01-E/02-E OPERATION MANUAL PREFACE This document indicates directions for use about the "MB96610 evaluation board" which is the evaluation environment of MB96610 series of a F2MC*1-16FX-16bit microcontroller*2. *1: F2MC is the abbreviation of FUJITSU Flexible Microcontroller. *2: Refered to MCU below. ■ Using the product safely This manual contains important information for using this product safely. Be sure to read this manual before using the product, and to follow the directions given in this manual in order to use the product correctly. In particular, thoroughly read "Caution of the product described in this manual" at the start of this document, and perform a thorough safety check before using the product. Store this manual in a safe location where it can easily be accessed at any time while you are using the product. ■ Related Manual You should refer for following Manual as well: MCU Evaluation Board MB2198-760-E OPERATION MANUAL Contents - MB96610 Evaluation Board Quantity Description Part No. 1 MB96610 Evaluation Board with socket MB2198-761-01-E 1 MB96610 Evaluation Board without socket (direct mounted) MB2198-761-02-E ■ European RoHS compliance Products with an -E suffix on the part number are European RoHS compliant products. ■ Notice on this document All information included in this document is current as of the date it is issued. Such information is subject to change without any prior notice. Please confirm the latest relevant information with the sales representatives. ■ Target products The available products with this evaluation board are shown below. Series MB96610 Product Number (not included Package suffix) MB96F612R, MB96F612A MB96F613R, MB96F613A MB96F615R, MB96F615A i ■ Caution of the product described in this manual The following precautions apply to the product described in this manual. WARNING Indicates a potentially hazardous situation which could result in death or serious injury and/or a fault in the user's system if the product is not used correctly. Electric shock, Damage Before performing any operation described in this manual, turn off all the power supplies to the system. Performing such an operation with the power on may cause an electric shock or device fault. Electric shock, Damage Once the product has been turned on, do not touch any metal part of it. Doing so may cause an electric shock or device fault. CAUTION Cuts, Damage Damage Damage Damage Damage Damage Damage Indicates the presence of a hazard that may cause a minor or moderate injury, damages to this product or devices connected to it, or may cause to loose software resources and other properties such as data, if the device is not used appropriately. Before moving the product, be sure to turn off all the power supplies and unplug the cables. Watch your step when carrying the product. Do not use the product in an unstable location such as a place exposed to strong vibration or a sloping surface. Doing so may cause the product to fall, resulting in an injury or fault. Do not place anything on the product or expose the product to physical shocks. Do not carry the product after the power has been turned on. Doing so may cause a malfunction due to overloading or shock. Since the product contains many electronic components, keep it away from direct sunlight, high temperature, and high humidity to prevent condensation. Do not use or store the product where it is exposed to much dust or a strong magnetic or electric field for an extended period of time. Inappropriate operating or storage environments may cause a fault. Use the product within the ranges given in the specifications. Operation over the specified ranges may cause a fault. To prevent electrostatic breakdown, do not let your finger or other object come into contact with the metal parts of any of the connectors. Before handling the product, touch a metal object (such as a door knob) to discharge any static electricity from your body. When installing the sub board, align the key positions of main board connector and sub board connector, and fix with the screw set before use. When removing, remove all screws of screw set, then remove the sub board vertically from the main board. Otherwise, the product may be damaged, such as corruption of the connector section. Because the product has no casing, it is recommended that it be stored in the original packaging. Transporting the product may cause a damage or fault. Therefore, keep the packaging materials and use them when re-shipping the product. ii The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU SEMICONDUCTOR semiconductor device; FUJITSU SEMICONDUCTOR does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU SEMICONDUCTOR or any third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU SEMICONDUCTOR assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Copyright ©2012 FUJITSU SEMICONDUCTOR LIMITED All rights reserved iii 1. Overview The MB96610 Evaluation Board provides the evaluative environment of the MB96610 series MCU. Figure 1 MB96610 Evaluation Board 1 1.1 Functional overview This board can mount MCU (with or without socket). The location of the main function is shown as follows. RS/USB selection monitor land Sub clock Main/Sub connector (solder side) OCD I/F Mode SW monitor land External Power Supply connection pin Main clock MCU socket monitor land monitor land Figure 2 MB96610 Evaluation Board functional overview 2 Main/Sub connector (solder side) Table 1 MB96610 Evaluation Board function list Function Specification Remarks MCU MB96F610 with socket or direct mounted with socket NQPACK048SD-ND HQPACK048SD Oscillator Main clock 4MHz Sub clock 32.768kHz with socket External power supply connection External power supply connection (DC3.3V to 5.0V) OCD connector OCD debugger(MB2100-01-E) Connection MODE SW MB96610 mode switch NMIX SW MB96610 pin monitor land RS/USB select UART ch.0 connect to RS/USB by 3pin Jumper for transmission and reception. Main/sub connector 26pins (2 rows 13 pins) connector 2 Connect to a connector on the Main board (mounted solder side) 2.54mm pitch 3 1.2 Block diagram The block diagram of this board is shown below. OCD connector Main board DC12V DC5V DC3.3V 4MHz 12V 5.0V 3.3V MCU 32kHz (MB96610) With Socket 48 Monitor land MODE SW USART ch.2 RS ch.0 USB USART ch.7 LIN ch.0 CAN ch.2 CAN ch.0 Monitor LED INT SW Figure 3 MB96610 Evaluation Board Block Diagram 4 2. Functional details The functional details of this board are shown as following. 2.1 Power supply settings Please confirm the following jumpers are closed. (J2, J4, J5, J14) AVCC AVSS VCC_MCU AVRH Figure 4 Power supply jumpers location Table 2 Power supply jumpers function Jumper Function Setting J2 [VCC_MCU] Power supply for VCC pin Close (default) : ON Open : OFF J14 [AVRH] Power supply for AVRH pin Close (default) : ON Open : OFF J4 [AVCC] Power supply for AVCC pin Close (default) : ON Open : OFF J5 [AVSS] Power supply for AVSS pin Close (default) : ON Open : OFF 5 2.2 Sub clock settings The sub clock connection can be set as follows by J7 and J24. The settings of these jumpers is shown below. Note: A sub clock oscillator is not mounted in default. (Xtal 32.768kHz) J24 J7 Figure 5 Sub clock jumpers location Table 3 J7 setting Setting X1A connection select 1-2 X1A connect to sub clock (default) 2-3 X1A connect to Q14 3 2 1 5 3 1 6 4 2 Table 4 J24 setting Setting 6 X0A connection select 1-3 X0A connect to GND 3-5 X0A connect to sub clock (default) 3-4 X0A connect to Q13 2.3 UART ch.0 select jumper The connection destination of the UART ch.0 signal can be selected by J20/J21. These jumpers location and settings are shown below. J20 J21 Figure 6 UART ch.0 select jumper location 3 2 1 From right to left 1, 2, 3 J20:TX , J21:RX Table 5 J20, J21 setting Setting Function select 1-2 RS232C (default) 2-3 USB 7 2.4 Mode SW settings The selection of the operational mode of MCU can be set by SW1 as follows. The mode switch location and settings are shown below. Mode SW Figure 7 Mode SW location 1 2 N O bit1:MD , bit2:DEBUG Table 6 Mode SW setting (SW1) 8 ON OFF Mode SW setting 1, 2 - MB96F610 : serial writer mode 1 2 MB96F610 : user mode (default) 2.5 OCD (On chip debugger) interface The MB96610 evaluation board can operate software "Softune" for debugging by connecting Fujitsu OCD-E (on chip debugger). The OCD connector location and settings are shown below. OCD connector Figure 8 OCD cable connect location Please turn the coaxial cable appended to Fujitsu OCD-E(MB21000-01-E) as shown in a left chart. Figure 9 How to connect OCD-E 9 2.6 Other jumper settings These jumpers are in order to free the MCU pin from on board peripherals. Table 7 Isolate jumpers location Jumper 10 Signal J12 LIN I/F ch.0 : RX J13 LIN I/F ch.0 : TX J8 RS I/F ch.0 (USB): RX J9 RS I/F ch.0 (USB): TX J10 CAN I/F ch.0 : RX J11 CAN I/F ch.0 : TX J19 LIN_NSLP0 J2 VCC_MCU : MCU power supply J4 AVCC : analog power supply J5 AVSS : analog ground J14 AVRH : analog reference power supply 2.7 Signal monitor The correspondence of the monitor land and the MCU pin number is shown as follows. (Q numbers are equal to MCU pin numbers.) Table 8 Monitor land list Q Pin No. Q Pin No. Q Pin No. 2 2 21 21 43 43 3 3 22 22 44 44 4 4 23 23 45 45 5 5 24 24 46 46 6 6 25 25 47 47 7 7 26 26 8 8 27 27 9 9 28 28 10 10 29 29 11 11 30 30 12 12 31 31 13 13 32 32 14 14 33 33 16 16 39 39 18 18 40 40 19 19 41 41 20 20 42 42 11 2.8 Main board connection The connection of MCU and I/O on the main board is shown below. ■ General-purpose LED The correspondence table for the general-purpose LED mounted on the main board and the MCU pin number is shown below. Table 9 General-purpose LED MB96610 MONITOR LED Parts number Pin number Pin name LED0 LED28 46 P6_0 LED1 LED29 47 P6_1 LED2 LED32 40 P3_0 LED3 LED33 41 P3_1 LED4 LED36 26 P1_4 LED5 LED37 27 P1_5 LED6 LED40 28 P1_6 LED7 LED41 29 P1_7 ■ Interrupt SW The correspondence of interruption SW mounted on the main board and the MCU pin number is shown below. Table 10 Interrupt switch MB96610 INT SW Parts number Pin number Pin name INT0 SW4 11 P05_6 (INT4_R) INT1 SW7 23 P00_3 (INT11) INT2 SW9 21 P00_4 (INT12) INT3 SW11 22 P00_5 (INT13) ■ NMI SW The correspondence of NMI SW mounted on the main board and the MCU pin number is shown below. Table 11 NMI switch MB96610 NMI SW Parts number Pin number NMI 12 SW3 12 Pin name NMI ■ Reset SW The correspondence of RESET SW mounted on the main board and the MCU pin number is shown below. Table 12 RESET switch MB96610 Reset SW Parts number Pin number RESET SW2 33 Pin name RSTX ■ Volume SW The correspondence of Volume SW mounted on the main board and the MCU pin number is shown below. Table 13 Volume switch MB96610 Volume SW Parts number Pin number Volume VR1 3 Pin name P06_3 (AN3) 13 3. Power-ON Basically, this board cannot turn on the power supply alone. Please mount on the main board(MB2198-760-E) and use it. 3.1 FOR TEST USE ONLY, External power supply connection pin The external power supply connection position is shown as follows. (VCC = 3.3V to 5.0V) When you connect an external power supply to this pin, and you use alone this board, please shortcircuit J22 (DVCC) and J23 (AVCC). VCC GND Figure 10 External power supply connection pin location 14 3.2 Power-ON Please follow the user's manual for the Main board(MB2198-760-E). 15 48pin socket type : NQPACK048SD (Socket Head : HQPACK048SD) FPT-48P-M26 Package code (mold) LQFP-48 VCC C P02_5/BIN0/IN1/TTG1/ADTG_R P03_0/AIN1/IN4/TTG4/AN24/TTG12 P03_1/BIN1/TTG5/TTG13/IN5/AN25 P03_2/INT10_R/RX2 P03_3/TX2 P03_6/ZIN1/OUT6/AN30 P03_7/OUT7/AN31 P06_0/AN0/PPG0 P06_1/AN1/PPG1 AVCC P01_1/TOT1/CKOTX1/OUT1_R P01_4/PPG4_B P01_5/SIN2_R/INT7_R P01_6/SOT2_R/PPG6_B P01_7/SCK2_R/PPG7_B P02_0/PPG12/CKOT1_R P02_2/ZIN0/PPG14/CKOT0_R P02_4/AIN0/IN0/TTG0 RSTX X1 X0 VSS P04_0/X0A P04_1/X1A MD P17_0 DEBUG I/F P00_0/INT8/SCK7_R/PPG0_B P00_1/INT9/SOT7_R/PPG1_B P00_2/INT10/SIN7_R P00_4/INT12/SOT8_R/PPG12_B P00_5/INT13/SIN8_R/PPG14_B P00_3/INT11/SCK8_R/PPG3_B P01_0/TIN1/CKOT1/OUT0_R 37 38 39 40 41 42 43 44 45 46 47 48 25 26 27 28 29 30 31 32 33 34 35 36 13 14 15 16 17 18 19 20 21 22 23 24 DGND AVSS WL-1-2P WL-1-2P R13 1 WL-1-2P WL-1-2P WL-1-2P VCC 2 2 2 2 2 C P02_5 P03_0 P03_1 P03_2 P03_3 P03_6 P03_7 P06_0 P06_1 P01_1 P01_4 P01_5 P01_6 P01_7 P02_0 P02_2 P02_4 RSTX X1 X0 X0A X1A MD P17_0 DEBUG_IF P00_0 P00_1 P00_2 P00_4 P00_5 P00_3 P01_0 (Qxx-Qyy = 2.54mm pitch) MB96F610 Monitor pin J10 1 J11 1 1005 10kΩ 5% 2 J19 1 J13 1 J12 1 2 2 Q44 Q Q Q45 Q Q46 Q Q47 Q39 Q Q Q40 Q Q41 Q42 Q Q Q43 Q21 Q Q Q22 Q Q23 Q Q24 Q Q19 Q Q20 Q Q25 Q Q26 Q Q27 Q Q28 Q Q29 Q Q30 Q Q31 Q Q32 Q Q33 Q Q16 Q Q18 Q9 Q Q Q10 Q Q11 Q Q12 1 WL-1-2P 1 J25 X0A (P04_0/X0A) C MB96F610 C-pin X1A (P04_1/X1A) 1 1 2 2 5 3 1 2 DGND 6 4 2 2 C11 2012 4.7μF 16V 1 VCC MD DEBUG 1 2 2 2 2 Q Q14 C15 1005 10pF 50V 1 J18 PM-1-3P 1 6 5 2 4 3 1 Oscillator X0A GND DGND Q13 4MHz MD1 DGND Q14 X1A 3 2 1 Oscillator DGND 32kHz DT-38_32.768kHz_SK Q Q13 C14 1005 10pF 50V DGND C13 1005 10pF 50V 1 J17 PM-1-3P P04_0 2 2 C12 1005 10pF 50V 1 DGND 4 3 P04_1 C J7 WL-1-3P 1 R12 1005 0Ω 2 WLW-1-3PW J24 1 R10 1005 0Ω 1 1005 10kΩ 5% 2 R4 CHS-02B SW1 MODE 2 2 HC49SFWB_4MHz_SK MB96F610 SubCLK IF X1 X0 MB96F610 MainCLK IF P17_0 MD DEBUG_IF OCD CN3 HRM-300-134B(40) 2 3 4 5 R2 1005 43Ω 5% 2 K A 1 1 D1 RN262GT2R J8 J9 VCC_MCU R18 R19 R21 R20 1 1 1 1 1 1 P07_0 Q Q87 Q Q86 P03_3 2 P05_0 2 RS/USB_RX P05_1 AVCC J4 WL-1-2P 2 2 1 LED1 CL-190G 1 DGND 2 J2 WL-1-2P VCC_MCU J21 WL-1-3P (RS:1pin-2pin short) (USB:2pin-3pin short) J20 WL-1-3P (RS:1pin-2pin short) (USB:2pin-3pin short) 1 3 5 7 9 11 13 15 17 19 21 23 25 2 4 6 8 10 12 14 16 18 20 22 24 26 DGND CN7 HIF3FB-26DA-2.54DSA(71) 2 DGND J5 WL-1-2P AVSS 2 2 2 2 2 (CN7-25,26pin) RS/USB_TX (NMI_SW) (RS_TX0) (RS_TX1) (CAN_TX0) (CAN_TX1) 1 R6 1005 470Ω Non-Mount 1 L1 BLM21PG600SN1 (CN6-23,25,26pin) [R18-R21] 1005 10kΩ 5% (LIN_TX0) P00_1 (LIN_NSLP0) P00_0 (LIN_TX1) Q Q85 VCC Main/Sub CN DGND AVCC DGND C22 3225 10μF 25V WL-1-2P WL-1-2P 1 2 1 VCC 1 2 Power Div IF C23 3225 10μF 25V VCC 1 2 MB96F610 MODE SET/OCD IF Non-Mount 1 2 Q Q2 Q Q7 Q Q8 AVRH Q Q3 Q Q4 Q Q5 Q Q6 Non-Mount DGND VCC_MCU VCC_MCU 2 1 2 R16 1608 10Ω 1% AVRH J14 WL-1-2P 1 R17 1608 4.7Ω 1% 2 1 2 AVRH P06_3 P06_4 P06_6 P06_7 P05_0 P05_1 P05_2 P05_4 P05_6 P07_0 1 2 1 2 1 2 3 4 5 6 7 8 9 10 11 12 1 2 C9 1005 0.01μF 25V AVSS AVRH P06_3/AN3/PPG3 P06_4/AN4/PPG4 P06_6/AN6/PPG6 P06_7/AN7/PPG7 P05_0/AN8/SIN2/INT3_R1 P05_1/AN9/SOT2 P05_2/AN10/SCK2 P05_4/AN12/TOT3/INT2_R P05_6/AN14/INT4_R P07_0/AN16/INT0/NMI GND Q Q36 Q Q37 VCC_MCU Q Q91 Q Q90 (RESET) (RS_RX0) (RS_RX1) AVCC Q Q53 VCC (CAN_RX0) (CAN_RX1) AVCC RSTX P03_2 (LIN_RX0) P00_2 (LIN_NSLP1) Q Q88 (LIN_RX1) Q Q89 C30 1005 22pF 25V AVCC1 R1 1005 10kΩ 5% R9 1005 1MΩ 5% R11 1005 1MΩ 5% C34 2012 1μF 16V C6 1005 0.01μF 25V 1 2 C1 1005 0.1μF 25V 1 2 Q Q51 Q Q84 1005 10kΩ 5% R22 1 2 (USB_RX0) VCC DGND DGND 25 23 21 19 17 15 13 11 9 7 5 3 1 2 1 AVCC DVCC_M Q Q49 (USB_TX0) (INT_SW0) (INT_SW2) (LED0) (LED2) (LED4) (LED6) +12V0 P05_6 P00_4 P06_0 P03_0 P01_4 P01_6 Q Q52 +12V0 DVCC_M DVCC_M 2 J23 WL-1-2P 1 J22 WL-1-2P GND VCC CN6 HIF3FB-26DA-2.54DSA(71) 26 24 22 20 18 16 14 12 10 8 6 4 2 AVSS Q Q1 Q Q48 AVCC1 Stand-alone J22-J23 short AVSS AVCC1 J16 WL-1-4P VCC AVSS AVRH AVCC1 J15 WL-1-4P DGND C33 1005 220pF 25V P06_3 P00_3 P00_5 P06_1 P03_1 P01_5 P01_7 +3V3 +3V3 C32 1005 0.1μF 25V (Volume_SW) (INT_SW1) (INT_SW3) (LED1) (LED3) (LED5) (LED7) +5V0 +5V0 Q Q50 1 2 C2 1005 0.1μF 25V Non-Mount R14 1005 1MΩ 5% Non-Mount R15 1005 1MΩ 5% 1 2 1 2 1 3 1 3 VCC_MCU C31 2012 1μF 16V NQPACK048SD(MB96F610) C29 1005 0.1μF 25V 1 2 2 R3 1005 10kΩ 5% 1 3 1 2 1 3 1 3 1 2 1 2 1 2 4 3 2 1 16 4 3 2 1 U1 4. Circuit diagram 5. Recycling Valid for European Union Countries: According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Semiconductor Europe GmbH Warehouse / Disposal Monzastraße 4a 63225 Langen Gültig für EU-Länder: Gemäß der Europäischen WEEE-Richtlinie und deren Umsetzung in landesspezifische Gesetze nehmen wir dieses Gerät wieder zurück. Zur Entsorgung schicken Sie das Gerät bitte an die folgende Adresse: Fujitsu Semiconductor Europe GmbH Warehouse / Disposal Monzastraße 4a 63225 Langen 17 6. China-RoHS regulation Compliance with Administration on the Control of Pollution Caused by Electronic Information Products of the People’s Republic of China 这标记是按照2006年2月28日公布的[电子信息产品污染控制管理办法]以及SJ/T11364-2006[电子信 息产品污染控制标识要求]在中国销售的电子信息产品的环保使用期限。如遵守关于这产品的安全或 使用上的注意，在这期限内(从生产日期起算)不会因产品中的有害物质漏到外部、或发生突然变异， 而引起环境污染和对人体或财产的重大影响。 产品中有毒有害物质或元素的名称及含量 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) 印刷线路板 × ○ ○ ○ ○ ○ 电源 ○ ○ ○ ○ ○ ○ ○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T 11363-2006规定的限量要求以下。 ×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T 11363-2006规定的限量要求。 18 SS704-00001-1v0-E FUJITSU SEMICONDUCTOR SUPPORT SYSTEM F2MC-16FX Family 16-BIT MICROCONTROLLER MB96610 series MB96610 Evaluation Board MB2198-761-01-E/02-E OPERATION MANUAL July 2012 the first edition Published FUJITSU SEMICONDUCTOR LIMITED Edited Sales Promotion Department