0.4MB

The following document contains information on Cypress products.
FUJITSU SEMICONDUCTOR
SUPPORT SYSTEM
SS704-00006-1v0-E
16-bit MICROCONTROLLER
2
F MC-16FX Family
MB96670 Evaluation Board
MB2198-767-01-E/02-E
OPERATION MANUAL
FUJITSU SEMICONDUCTOR CONFIDENTIAL
PREFACE
This document indicates directions for use about the "MB96670 evaluation board" which is the evaluation
environment of MB96670 series of a F2MC*1-16FX-16bit microcontroller*2.
*1: F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
*2: Refered to MCU below.
 Using the product safely
This manual contains important information for using this product safely.
Be sure to read this manual before using the product, and to follow the directions given in this manual in
order to use the product correctly.
In particular, thoroughly read "Caution of the product described in this manual" at the start of this document,
and perform a thorough safety check before using the product.
Store this manual in a safe location where it can easily be accessed at any time while you are using the
product.
 Related Manual
You should refer for following Manual as well:
· MCU Evaluation Board MB2198-760-E OPERATION MANUAL
Contents - MB96670 Evaluation Board
Quantity
Description
Part No.
1
MB96670 Evaluation Board with socket
MB2198-767-01-E
1
MB96670 Evaluation Board without socket (direct mounted)
MB2198-767-02-E
 European RoHS compliance
Products with an -E suffix on the part number are European RoHS compliant products.
 Notice on this document
All information included in this document is current as of the date it is issued. Such information is subject
to change without any prior notice.
Please confirm the latest relevant information with the sales representatives.
 Target products
The available products with this evaluation board are shown below.
Series
MB96670
Product Number (not included Package suffix)
MB96F673R, MB96F673A
MB96F675R, MB96F675A
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
i
 Caution of the product described in this manual
The following precautions apply to the product described in this manual.
WARNING
Indicates a potentially hazardous situation which could result in death or serious
injury and/or a fault in the user's system if the product is not used correctly.
Electric shock,
Damage
Before performing any operation described in this manual, turn off all the power
supplies to the system.
Performing such an operation with the power on may cause an electric shock or
device fault.
Electric shock,
Damage
Once the product has been turned on, do not touch any metal part of it.
Doing so may cause an electric shock or device fault.
CAUTION
Cuts, Damage
Indicates the presence of a hazard that may cause a minor or moderate injury,
damages to this product or devices connected to it, or may cause to loose software
resources and other properties such as data, if the device is not used appropriately.
Before moving the product, be sure to turn off all the power supplies and unplug
the cables. Watch your step when carrying the product. Do not use the product in
an unstable location such as a place exposed to strong vibration or a sloping
surface.
Doing so may cause the product to fall, resulting in an injury or fault.
Damage
Do not place anything on the product or expose the product to physical shocks. Do
not carry the product after the power has been turned on.
Doing so may cause a malfunction due to overloading or shock.
Damage
Since the product contains many electronic components, keep it away from direct
sunlight, high temperature, and high humidity to prevent condensation. Do not use
or store the product where it is exposed to much dust or a strong magnetic or
electric field for an extended period of time.
Inappropriate operating or storage environments may cause a fault.
Damage
Use the product within the ranges given in the specifications.
Operation over the specified ranges may cause a fault.
Damage
To prevent electrostatic breakdown, do not let your finger or other object come
into contact with the metal parts of any of the connectors. Before handling the
product, touch a metal object (such as a door knob) to discharge any static
electricity from your body.
Damage
When installing the sub board, align the key positions of main board connector and
sub board connector, and fix with the screw set before use. When removing,
remove all screws of screw set, then remove the sub board vertically from the
main board. Otherwise, the product may be damaged, such as corruption of the
connector section.
Damage
Because the product has no casing, it is recommended that it be stored in the
original packaging. Transporting the product may cause a damage or fault.
Therefore, keep the packaging materials and use them when re-shipping the
product.
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
ii
 The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
 The information, such as descriptions of function and application circuit examples, in this document are presented
solely for the purpose of reference to show examples of operations and uses of FUJITSU SEMICONDUCTOR
semiconductor device; FUJITSU SEMICONDUCTOR does not warrant proper operation of the device with respect to
use based on such information. When you develop equipment incorporating the device based on such information, you
must assume any responsibility arising out of such use of the information. FUJITSU SEMICONDUCTOR assumes no
liability for any damages whatsoever arising out of the use of the information.
 Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as
license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of
FUJITSU SEMICONDUCTOR or any third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of
any third-party's intellectual property right or other right by using such information. FUJITSU SEMICONDUCTOR
assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would
result from the use of information contained herein.
 The products described in this document are designed, developed and manufactured as contemplated for general use,
including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not
designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless
extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal
injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air
traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for
use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or
damages arising in connection with above-mentioned uses of the products.
 Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from
such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire
protection, and prevention of over-current levels and other abnormal operating conditions.
 Exportation/release of any products described in this document may require necessary procedures in accordance with
the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
 The company names and brand names herein are the trademarks or registered trademarks of their respective owners.
Copyright ©2013 FUJITSU SEMICONDUCTOR LIMITED All rights reserved.
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
iii
1. Overview
The MB96670 Evaluation Board provides the evaluative environment of the MB96670 series MCU
Figure1 MB96670 Evaluation Board
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
1
1.1. Functional overview
This board can mount MCU (with or without socket).
The location of the main function is shown as follows.
Figure2 MB96670 Evaluation Board functional overview
RS/USB
sel
monitor
Main
xtal
Main/Sub
connector
(solder side)
OCD
I/F
Sub
xtal
Mode
SW
monitor
MCU
socket
monitor
Main/Sub
connector
(solder side)
monitor
External
Power
connection
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
2
Table1 MB96670 Evaluation Board function list
Function
Specification
Remarks
MCU
MB96F670
with socket or direct mounted
with socket
NQPACK064SD-ND
HQPACK064SD
Oscillator
Main clock 4MHz
Sub clock 32.768kHz
with socket
External power supply
connection
External power supply connection
(DC3.3V to 5.0V)
OCD connector
OCD debugger(MB2100-01-E)
Connection
MODE SW
MB96670 mode switch
NMIX SW
MB96670 pin monitor land
RS/USB select
UART ch.0 connect to RS/USB by 3pin Jumper
for transmission and reception.
Main/sub connector
26pins (2 rows × 13 pins) connector × 2
Connect to a connector on the Main board
(mounted solder side)
2.54mm pitch
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
3
1.2. Block diagram
The block diagram of this board is shown below.
Figure3 MB96670 Evaluation Board Block Diagram
OCD connector
Main board
DC12V→
· DC5V
· DC3.3V
4MHz
12V
5.0V
3.3V
32kHz
MCU
(MB96670)
With
MODE SW
Socket 64
Monitor
land
USART ch.0
RS ch.0
USB
USART ch.1
CAN ch.0
LIN ch.0
CAN ch.0
Monitor LED
INT SW
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
4
2. Functional details
The functional details of this board are shown as following.
2.1. Power supply settings
Please confirm the following jumpers are closed.
(J2, J3, J4, J5, J14)
Figure4 Power supply jumpers location
AVCC
AVSS
VCC_MCU
AVRH
DVCC
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
5
Table2
Power supply jumpers function
Jumper
Function
Setting
J2
[VCC_MCU]
Power supply for VCC pin
Close (default): ON
Open: OFF
J14
[AVRH]
Power supply for AVRH pin
Close (default): ON
Open: OFF
J3
[DVCC]
Power supply for DVCC pin
Close (default): ON
Open: OFF
J4
[AVCC]
Power supply for AVCC pin
Close (default): ON
Open: OFF
J5
[AVSS]
Power supply for AVSS pin
Close (default): ON
Open: OFF
2.2. Sub clock settings
The sub clock connection can be set as follows by J7 and J24.
The settings of these jumpers is shown below.
Note: A sub clock oscillator is not mounted in default. (Xtal 32.768kHz)
Figure5 Sub clock jumpers location
J7
J24
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
6
Table3 J7 setting
Setting
X1A connection select
1-2
X1A connect to sub clock (default)
2-3
X1A connect to Q41
3
2
1
Table4 J24 setting
Setting
X0A connection select
1-3
X0A connect to GND
5
3
1
3-5
X0A connect to sub clock (default)
6
4
2
3-4
X0A connect to Q40
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
7
2.3. UART ch.0 select jumper
The connection destination of the UART ch.0 signal can be selected by J20/J21.
These jumpers location and settings are shown below.
Figure6 UART ch.0 select jumper location
J21
J20
3
2
1
From right to left 1, 2, 3
J20:TX , J21:RX
Table5 J20, J21 setting
Setting
Function select
1-2
RS232C (default)
2-3
USB
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
8
2.4. Mode SW settings
The selection of the operational mode of MCU can be set by SW1 as follows.
The mode switch location and settings are shown below.
Figure7 Mode SW location
Mode SW
1
2
N
O
bit1:MD , bit2:DEBUG
Table6 Mode SW setting (SW1)
ON
OFF
Mode SW setting
1,2
-
MB96670 : serial writer mode
1
2
MB96670 : user mode (default)
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
9
2.5. OCD (On chip debugger) interface
The MB96670 evaluation board can operate software "Softune" for debugging by connecting Fujitsu
OCD-E (on chip debugger). The OCD connector location and settings are shown below.
Figure8 OCD cable connect location
OCD
connector
Figure9
How to connect OCD-E
Please turn the coaxial cable appended to Fujitsu
OCD-E(MB2100-01-E) as shown in a left chart.
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
10
2.6. Other jumper settings
These jumpers in the table can control the connection between the MCU pin and the peripheral I/O.
Table7 Isolate jumpers location
Jumper
Signal
J8
RS I/F ch.0 (USB): RX
J9
RS I/F ch.0 (USB): TX
J12
LIN I/F ch.0 : RX
J13
LIN I/F ch.0 : TX
J19
LIN_NSLP0
J10
CAN I/F ch.0 : RX
J11
CAN I/F ch.0 : TX
J2
VCC_MCU : MCU power supply
J3
DVCC : digital power supply
J4
AVCC : analog power supply
J5
AVSS : analog ground
J14
AVRH : analog reference power supply
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
11
2.7. Signal monitor
The correspondence of the monitor land and the MCU pin number is shown as follows. (Q numbers are
equal to MCU pin numbers.)
Table8 Monitor land list
Q
Pin No.
Q
Pin No.
Q
Pin No.
3
3
26
26
52
52
4
4
27
27
53
53
5
5
28
28
54
54
6
6
29
29
55
55
7
7
30
30
56
56
8
8
31
31
57
57
9
9
32
32
58
58
10
10
33
33
59
59
11
11
35
35
60
60
12
12
42
42
61
61
13
13
43
43
62
62
15
15
44
44
63
63
17
17
45
45
18
18
46
46
19
19
47
47
20
20
48
48
21
21
49
49
22
22
50
50
25
25
51
51
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
12
2.8. Main board connection
The connection of MCU and I/O on the main board is shown below.
 General-purpose LED
The correspondence table for the general-purpose LED mounted on the main board and the MCU pin
number is shown below.
Table9 General-purpose LED
MONITOR LED
MB96670
Parts number
Pin number
Pin name
LED0
LED28
19
P8_0
LED1
LED29
20
P8_1
LED2
LED32
21
P8_2
LED3
LED33
22
P8_3
LED4
LED36
25
P8_4
LED5
LED37
26
P8_5
LED6
LED40
27
P8_6
LED7
LED41
28
P8_7
 Interrupt SW
The correspondence of interruption SW mounted on the main board and the MCU pin number is shown
below.
Table10 Interrupt switch
INT SW
MB96670
Parts number
Pin number
Pin name
INT0
SW4
5
P13_1 (INT3)
INT1
SW7
17
P05_4 (INT2_R)
INT2
SW9
54
P12_7 (INT1_R)
INT3
SW11
44
P11_0
 NMI SW
The correspondence of NMI SW mounted on the main board and the MCU pin number is shown below.
Table11 NMI switch
NMI SW
NMI
MB96670
Parts number
SW3
Pin number
Pin name
63
NMI
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
13
 Reset SW
The correspondence of RESET SW mounted on the main board and the MCU pin number is shown below.
Table12
RESET switch
Reset SW
RESET
MB96670
Parts number
SW2
Pin number
Pin name
42
RSTX
 Volume SW
The correspondence of Volume SW mounted on the main board and the MCU pin number is shown below.
Table13 Volume switch
Volume SW
Volume
MB96670
Parts number
VR1
Pin number
Pin name
12
P05_0 (AN8)
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
14
3. Power-ON
Basically, this board cannot turn on the power supply alone.
Please mount on the main board(MB2198-760-E) and use it.
3.1. FOR TEST USE ONLY, External power supply
connection pin
The external power supply connection position is shown as follows.
(VCC = 3.3V to 5.0V)
When you connect an external power supply to this pin, and you use alone this board, please short-circuit
J22 (DVCC) and J23 (AVCC).
Figure10 External power supply connection pin location
VCC
GND
3.2. Power-ON
Please follow the user's manual for the Main board(MB2198-760-E).
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
15
A
B
C
D
(Socket Head : HQPACK064SD)
64pin socket type : NQPACK064SD-ND
FPT-64P-M23/M24
Package code (mold)
LQFP-64
5
VCC
P03_6/INT0/NMI
P03_5/TX0
P03_4/RX0/INT4
P03_3/SEG39
P03_2/SEG38
P03_1/SEG37
P03_0/SEG36
P01_3/SEG23
P01_1/SEG21/CKOT1
P12_7/SEG11/INT1_R
P12_6/SEG10/TOT2_R/PPG3_B
P12_5/SEG9/TIN2_R/PPG2_B
P12_4/SEG8
P12_2/SEG6/TOT1_R/PPG1_B
P12_1/SEG5/TIN1_R/PPG0_B
P12_0/SEG4/IN1_R
P11_3/COM3/PPG2_R
P11_2/COM2/PPG1_R
P11_1/COM1/PPG0_R
P11_0/COM0
P11_7/SEG3/IN0_R
RSTX
P04_1/X1A
P04_0/X0A
VSS
X1
X0
MD
P17_0
DEBUG I/F
P04_5/SCL0
P04_4/PPG3/SDA0
P13_6/SCK0/CKOTX0/SEG47
P13_5/SOT0/ADTG/INT7/SEG46
P13_4/SIN0/INT6/SEG45
P08_7/PWM2M1/AN23
P08_6/PWM2P1/AN22
P08_5/PWM1M1/AN21
P08_4/PWM1P1/AN20
DVSS
DVCC
P08_3/PWM2M0/AN19
P08_2/PWM2P0/AN18
P08_1/PWM1M0/AN17
P08_0/PWM1P0/AN16
P05_5/AN13
P05_4/AN12/INT2_R
AVSS
AVRH
AVCC
P05_1/AN9
P05_0/AN8
P06_7/TOT1/SEG56/IN5_R
P06_6/TIN1/SEG55/IN4_R
P06_5/IN1/SEG54/TTG1
P02_2/SEG30/CKOT0_R
P01_0/SEG20/SGA0
P00_7/SEG19/SGO0
P13_1/INT3/SCK1/SEG42
DGND
DVSS
AVSS
VCC
P00_7
P01_0
P02_2
P08_0
P08_1
P08_2
P08_3
19
21
22
2
P05_5
18
20
MD
X0
X1
37
38
P11_7
P11_0
P11_1
P11_2
P11_3
P12_0
43
44
45
46
47
48
P01_3
P03_0
P03_1
P03_2
P03_3
57
58
59
60
WL-1-2P
62
64
63
WL-1-2P
61
J11
P03_6
P03_5
4
(Qxx-Qyy = 2.54mm pitch)
MB96F670 Monitor pin
1
2
P12_7
P01_1
54
56
P03_4
P12_6
1
P12_5
53
J10
P12_4
52
55
P12_2
50
51
P12_1
RSTX
42
1005 10kohm 5%
X1A
41
49
X0A
40
2
P17_0
35
36
R13
DEBUG_IF
34
2
P04_5
33
1
P04_4
39
P13_6
P13_5
32
2
31
1
WL-1-2P
30
J9
P13_4
WL-1-2P
P08_6
29
P08_5
27
P08_7
P08_4
25
28
26
24
23
P05_4
17
16
15
1
P05_1
13
14
J8
P05_0
12
AVRH
P06_6
P06_7
10
11
P06_5
2
P13_1
1
9
J19
8
WL-1-2P
5
6
7
Q63
Q61
Q62
Q60
Q59
Q57
Q58
Q56
Q55
Q54
Q53
Q52
Q51
Q50
Q49
Q48
Q47
Q46
Q45
Q44
Q43
Q42
Q35
Q33
Q32
Q31
Q29
Q30
Q28
Q27
Q26
Q25
Q22
Q21
Q20
Q19
Q18
Q17
Q15
AVRH
Q
Q13
Q
Q12
Q
Q11
Q
Q10
Q
Q9
Q
Q8
Q
Q7
Q
Q6
Q
Q5
J25
WL-1-2P
1
R3
X0A
(P04_0/X0A)
C
MB96F670 C-pin
X1A
(P04_1/X1A)
2
MB96F670 SubCLK IF
X1
X0
2
1
2
5
3
1
2
2
3
4
1
DGND
2
P04_1
6
4
2
2
P04_0
C11
2012 4.7uF 16V
C
WL-1-3P
J7
1
1005 0ohm
R12
WLW-1-3PW
J24
1
1005 0ohm
R10
1
2
1005 43ohm 5%
R2
VCC
2
2
2
2
Q
Q41
3
1005 10pF 50V
C15
1
PM-1-3P
J18
1
1
5 6
3 4
1 2
Oscillator
X0A
GND
DGND
4MHz
MD1
Q40
DGND
Q41
X1A
3
2
1
Oscillator
DGND
32kHz
DT-38_32.768kHz_SK
Q
Q40
1005 10pF 50V
C14
DGND
1005 10pF 50V
C13
1
PM-1-3P
J17
1
OCD
HRM-300-134B(40)
CN3
DEBUG
MD
1005 10pF 50V
C12
1005 10kohm 5%
2
R4
CHS-02B
SW1
MODE
AT-49_4MHz_SK
DGND
MB96F670 MainCLK IF
P17_0
MD
DEBUG_IF
1
2
Q
Q4
1
2
P13_0
D1
2
RN262GT2R
1
2
J13
3
WL-1-2P
K 2
A
1
4
4
P13_0/INT2/SOT1
5
Q
Q3
VCC_MCU
VCC
1
C22
P03_6
Q
Q87
Q
Q86
P03_5
AVCC
WL-1-2P
J5
AVSS
2
2
2
2
2
1
LED1
CL-190G
1
6
8
10
12
14
16
18
20
22
24
26
5
7
9
11
13
15
17
19
21
23
25
WL-1-3P
4
3
WL-1-3P
(USB:2pin-3pin short)
(RS:1pin-2pin short)
J21
(USB:2pin-3pin short)
(RS:1pin-2pin short)
J20
2
1
2
DGND
2
DGND
HIF3FB-26DA-2.54DSA(71)
CN7
DGND
2
2
WL-1-2P
J2
VCC_MCU
2011/10/17 C12-C14:22pF->10pF (Rev0.1->Rev1.0)
P13_4
RS/USB_RX
P13_5
RS/USB_TX
(NMI_SW)
(RS_TX1)
(RS_TX0)
(CAN_TX1)
(CAN_TX0)
Q
Q85
P02_2
(LIN_TX1)
(LIN_NSLP0)
1
2
1
R20
2
1
2
R21
1
P13_0
!
1
1
WL-1-2P
J4
(CN7-25,26pin)
1005 10kohm 5%
[R18-R21]
1
R6
1005 470ohm 5%
Non-Mount
1
BLM21PG600SN1
L1
(CN6-23,25,26pin)
R19
R18
(LIN_TX0)
VCC
Main/Sub CN
DGND
AVCC
DGND
2
P03_7
3225 10uF 25V
2
1
2
1
C23
J12
3225 10uF 25V
WL-1-2P
1
2
3
2
1
2
P03_7/INT1/SIN1
1
Q91
Q90
Q89
Q88
AVCC
AVCC
RSTX
P03_4
P03_7
2
1608 10ohm 1%
R16
2
WL-1-2P
AVRH
J14
1
1608 4.7ohm 1%
R17
DGND
VCC_MCU
VCC_MCU
C9
Power Div IF
C6
VCC
GND
Q1
Q64
C31
DVSS
1
VCC
VCC
WL-1-4P
J15
VCC
P08_5
P08_7
(LED5)
(LED7)
Q92
Date:
(USB_RX0)
DGND
Monday, April 16, 2012
MB2198-767-0x-E
Document Number
DVSS
1
DGND
AVRH
AVCC1
3225 10uF 25V
26
2
6
4
8
10
12
14
16
18
20
1
AVCC1
GND
WL-1-4P
J16
DGND
2
GND
Q24
Q23
DVCC
DVCC
1
1
P08_6
P08_4
P08_2
P08_0
P12_7
AVCC
of
+12V0
Q68
1
Rev
1.0
(USB_TX0)
(LED6)
(LED4)
(LED2)
(LED0)
(INT_SW2)
(INT_SW0)
Q65
+12V0
DVCC_M
DVCC_M
2
WL-1-2P
2
WL-1-2P
P13_1
J23
1
J22
DVCC_M
AVSS
Q16
Q14
AVCC1
Stand-alone J22-J23 short
AVSS
VCC
Sheet
1
3
5
7
9
11
13
15
17
19
21
23
25
DVCC
WL-1-2P
J3
DVCC
DVSS
1
CN6
HIF3FB-26DA-2.54DSA(71)
MB96F670 SUB BOARD
1
1005 10kohm 5%
R22
Size
A3
Title
P08_3
Q84
P08_1
(LED3)
(RESET)
P11_0
(LED1)
P05_4
(INT_SW3)
(INT_SW1)
(RS_RX1)
(CAN_RX1)
(RS_RX0)
P05_0
(Volume_SW)
(CAN_RX0)
2
2
AVSS
22
2
+3V3
+3V3
Q
Q67
2
Non-Mount
L5
BLM21PG600SN1
1
24
+5V0
DVCC
DGND
1
1005 0ohm
R8
(CN6-21pin)
BLM21PG600SN1
L2
(LIN_RX1)
Q
Q66
C25
(LIN_NSLP1)
(LIN_RX0)
2012 1uF 16V
+5V0
VCC_MCU
DVCC_M
C26
MB96F670 MODE SET/OCD IF
1
2
C
1005 0.01uF 25V
2
C30
C
DVCC
1005 22pF 25V
1
1
2
1
2
3
C28
VSS
Non-Mount
3225 10uF 25V
C32
1005 10kohm 5%
1
2
C1
2012 1uF 16V
1
2
1005 0.1uF 25V
1
2
NQPACK064SD-ND(MB96F670)
Non-Mount
C34
1005 0.1uF 25V
1
2
3225 10uF 25V
C33
1
2
1005 220pF 25V
1
2
1
2
1
2
C2
Non-Mount
R14
Non-Mount
R15
1005 0.01uF 25V
1
2
1005 0.1uF 25V
1005 1Mohm 5%
1005 1Mohm 5%
1
2
4
1
2
U2
AVCC1
C29
1
2
R1
R9
1005 1Mohm 5%
R11
1005 1Mohm 5%
1
2
C21
VCC_MCU
1005 0.1uF 25V
1
3
1
3
1
2
1
2
4
1005 10kohm 5%
1
3
1
2
1
3
1
3
C27
3
C4
3
3225 10uF 25V
2
1005 0.1uF 25V
2
2
1
1
2
1
FUJITSU SEMICONDUCTOR CONFIDENTIAL
4
1005 0.01uF 25V
5
A
B
C
D
4. Circuit diagram
FUJITSU SEMICONDUCTOR LIMITED
16
5. Recycling
Valid for European Union Countries:
According to the European WEEE-Directive and its implementation into national laws we
take this device back.
For disposal please send the device to the following address:
Fujitsu Semiconductor Europe GmbH
Warehouse / Disposal
Monzastraße 4a
63225 Langen
Gültig für EU-Länder:
Gemäß der Europäischen WEEE-Richtlinie und deren Umsetzung in landesspezifische
Gesetze nehmen wir dieses Gerät wieder zurück.
Zur Entsorgung schicken Sie das Gerät bitte an die folgende Adresse:
Fujitsu Semiconductor Europe GmbH
Warehouse / Disposal
Monzastraße 4a
63225 Langen
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
17
6. China-RoHS regulation
Compliance with Administration on the Control of Pollution Caused by Electronic Information Products of
the People’s Republic of China
这 标 记 是 按 照 2006 年 2 月 28 日 公 布 的 [ 电 子 信 息 产 品 污 染 控 制 管 理 办 法 ] 以 及
SJ/T11364-2006[电子信息产品污染控制标识要求]在中国销售的电子信息产品的环保
使用期限。如遵守关于这产品的安全或使用上的注意，在这期限内(从生产日期起算)
不会因产品中的有害物质漏到外部、或发生突然变异，而引起环境污染和对人体或财
产的重大影响。
产品中有毒有害物质或元素的名称及含量
有毒有害物质或元素
部件名称
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印刷线路板
×
○
○
○
○
○
电源
○
○
○
○
○
○
○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T 11363-2006规定的限量要求以下。
×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T 11363-2006 规定的限量要求。
FUJITSU SEMICONDUCTOR LIMITED
FUJITSU SEMICONDUCTOR CONFIDENTIAL
18
SS704-00006-1v0-E
FUJITSU SEMICONDUCTOR · SUPPORT SYSTEM
F2MC-16FX Family
16-BIT MICROCONTROLLER
MB96670 Evaluation Board
MB2198-767-01-E/02-E
OPERATION MANUAL
February 2013 the first edition
Published
FUJITSU SEMICONDUCTOR LIMITED
Edited
Sales Promotion Department
FUJITSU SEMICONDUCTOR CONFIDENTIAL