The following document contains information on Cypress products. FM4 Family 32-BIT Microcontroller MB9B360L DATA SHEET Errata Sheet Page Item Original document code: DS709-00007-1v0-E Rev 1.0 April 25, 2014 33 I/O CIRCUIT TYPE Description It should be added as indicated by the shading below. Type Circuit I P-ch P-ch N-ch R Publication Number MB9B360L_DS709-00007-1v0-E-DE CONFIDENTIAL Remarks ・ CMOS level output ・ CMOS level hysteresis input ・ 5V tolerant Digital output ・ With standby mode control ・ Pull-up resistor Digital output : Approximately 50kΩ ・ IOH = -4mA, IOL = 4mA ・ Available to control of Pull-up resistor PZR registers. control ・ When this pin is used as Digital input an I2C pin, the digital Standby mode output P-ch transistor is control always off Revision 1.0 Issue Date April 25, 2014 E R R A T A Page 54 Item Pin Status S H E E T Description “List of VBAT Domain Pin Status” should be corrected as indicated by the shading below. VBAT pin status type (Error) Function group INITX input state Device internal reset state Power supply stable INITX=0 ‐ INITX=1 ‐ TIMER mode, RTC mode, or STOP mode state Deep standby RTC mode or Deep standby STOP mode state Return from Deep standby mode state Power supply stable Power supply stable Power supply stable INITX=1 SPL=0 SPL=1 INITX=1 SPL=0 SPL=1 INITX=1 - Hi-Z / S GPIO selected Setting disabled Setting disabled Maintain previous state Internal input fixed at "0" Hi-Z / GPIO selected Setting disabled Setting disabled External sub clock input selected Maintain previous state Maintain Setting disabled Setting disabled previous state T Internal input fixed at "0" Hi-Z / Internal input fixed at "0" GPIO selected Internal input fixed at "0" GPIO selected Internal input fixed at "0" Maintain previous state Hi-Z / Internal input fixed at "0" GPIO selected Hi-Z / Internal input fixed GPIO selected at "0" Hi-Z / Internal input fixed Maintain previous state at "0" Maintain Maintain Maintain previous previous previous state/When state/When state/When state/When oscillation oscillation oscillation oscillation stops*, stops*, stops*, stops*, Hi-Z/ Hi-Z / Hi-Z/ Hi-Z/ Internal Internal Internal Internal input fixed input fixed input fixed input fixed input fixed at "0" at "0" at "0" at "0" at "0" Hi-Z / Internal Hi-Z / Internal Sub crystal oscillation input input oscillator stops*, fixed fixed output pin Hi-Z / at "0" at "0" Internal Maintain previous Maintain previous state/When *Oscillation is stopped at STOP mode and Deep standby STOP mode. 2 CONFIDENTIAL MB9B360L_DS709-00007-1v0-E-DE1, April 25, 2014 E R R A T A Page Item Pinstatus Description (Correct) VBAT pin status type 54 S H E E T S Function group INITX input state Device internal reset state Return Deep standby from RTC mode or Deep standby Deep standby STOP mode state mode state TIMER mode, RTC mode, or STOP mode state Power supply stable Power supply stable Power supply stable Power supply stable INITX=1 SPL=0 SPL=1 INITX=1 SPL=0 SPL=1 INITX=1 - INITX=0 ‐ INITX=1 ‐ Maintain previous state Maintain Maintain previous state Maintain Maintain previous state Maintain Maintain previous state Maintain Maintain previous state Maintain previous state External sub Maintain previous state Maintain previous state Maintain previous state Maintain previous state Maintain clock input previous previous previous previous previous state state state state state GPIO selected GPIO selected selected T Maintain Sub crystal Maintain Maintain previous oscillator previous previous state/When output pin state state oscillation stops, Maintain Maintain previous state/When oscillation Hi-Z* stops, Hi-Z* previous state/When oscillation stops, Hi-Z* Maintain Maintain previous previous state state Maintain Maintain previous previous state state Maintain Maintain previous previous state state Maintain previous state/When Maintain previous oscillation state stops, Hi-Z* *When The SOSCNTL bit in the WTOSCCNT Register is “0”, Sub crystal oscillator output pin is maintain previous state. When The SOSCNTL bit in the WTOSCCNT Register is “1”, Oscillation is stopped at STOP mode and Deep standby STOP mode. 57 ELECTRICAL It should be corrected as indicated by the shading below. CHARACTERIS TICS Parameter Symbol Conditions Value Min Max Unit Remarks 2.Recommended Power supply voltage VCC 2.7*5 5.5 V Operating *5: In between less than the minimum power supply voltage and low voltage reset/interrupt Conditions detection voltage or more, instruction execution and low voltage detection function by built-in High-speed CR (including Main PLL is used) or built-in Low-speed CR is possible to operate only. April 25, 2014, MB9B360L_DS709-00007-1v0-E-DE1 CONFIDENTIAL 3 E R R A T A Page 70 Item S H E E T Description “(3) Built-in CR Oscillation Characteristics” should be corrected as indicated by the shading below. ELECTRICAL CHARACTERIS ・ Built-in High-speed CR TICS 4. AC Characteristics (VCC = 2.7V ~ 5.5V, VSS = 0V) Parameter Symbol Clock frequency FCRH Value Min Typ Max Conditions Tj = -20°C to + 105°C Tj = - 40°C to + 125°C 3.92 3.88 4 4 4.08 4.12 Tj = - 40°C to + 125°C 3 4 5 Unit Remarks When trimming*1 MHz When not trimming Frequency stabilization tCRWT 30 μS *2 time *1: In the case of using the values in CR trimming area of Flash memory at shipment for frequency/temperature trimming. *2: This is the time to stabilize the frequency of high-speed CR clock after setting trimming value. This period is able to use high-speed CR clock as source clock. 109 ELECTRICAL “Electrical Characteristics for the A/D Converter” should be added as indicated by the shading below. CHARACTERIS (VCC = AVCC = 2.7Vto5.5V, VSS = AVSS = 0V) TICS 6. 12-bit D/A Converter tc20 tc100 Value Min Typ 0.56 0.69 2.79 3.42 Max 12 0.81 4.06 INL - 16 - + 16 LSB - 0.98 - + 1.5 LSB - - 10.0 mV - 20.0 - + 1.4 mV Parameter Symbol Resolution Conversion time Integral Nonlinearity* Differential Nonlinearity* DNL Output voltage offset VOFF Analog output impedance RO Power supply current* IDDA IDSA Pin name DAx AVCC Unit Remarks bit μs Load 20pF μs Load 100pF 3.10 3.80 2.0 - 4.50 kΩ MΩ 260 330 410 μA 400 519 620 μA - - 14 μA When setting 0x000 When setting 0xFFF D/A operation When D/A stop D/A operation AVCC=3.3V D/A operation AVCC=5.0V When D/A stop *: During no load 4 CONFIDENTIAL MB9B360L_DS709-00007-1v0-E-DE1, April 25, 2014 E R R A T A Page 116 S H E E T Item Description ELECTRICAL “Recovery count time” of “(1) Recovery cause: Interrupt/WKUP” should be corrected as indicated by the CHARACTERIS shading below. TICS (Error) Parameter 11. Standby Recovery Time Sub timer mode RTC mode Stop mode (High-speed CR /Main/PLL run mode return) RTC mode Stop mode (Low-speed CR/sub run mode return) Symbol Ticnt Deep standby RTC mode with RAM retention Deep standby stop mode with RAM retention Value Unit Min Max Remarks 881 1136 μs 270 581 μs 240 480 μs 308 667 μs without RAM retention 308 667 μs with RAM retention (Correct) Parameter Sub timer mode RTC mode stop mode (High-speed CR /Main/PLL run mode return) RTC mode stop mode (Low-speed CR/sub run mode return) Deep standby RTC mode with RAM retention Deep standby stop mode with RAM retention April 25, 2014, MB9B360L_DS709-00007-1v0-E-DE1 CONFIDENTIAL Symbol Ticnt Value Unit Min Max Remarks 896 1136 μs 316 581 μs 270 540 μs 365 667 μs without RAM retention 365 667 μs with RAM retention 5 E R R A T A Page 118 Item S H E E T Description ELECTRICAL “Recovery count time” of “(2) Recovery cause: Reset” should be corrected as indicated by the shading CHARACTERIS below. TICS (Error) 11. Standby Recovery Time Parameter Sleep mode High-speed CR Timer mode Main Timer mode PLL Timer mode Low-speed CR timer mode Sub timer mode RTC mode Stop mode Symbol Trcnt Deep standby RTC mode with RAM retention Deep standby stop mode with RAM retention Value Unit Min Max 266 116 μs Remarks 116 266 μs 258 258 567 567 μs μs 258 567 μs 308 667 μs without RAM retention 308 667 μs with RAM retention (Correct) Parameter Sleep mode High-speed CR Timer mode Main Timer mode PLL Timer mode Low-speed CR timer mode Sub timer mode RTC mode Stop mode Deep standby RTC mode with RAM retention Deep standby stop mode with RAM retention 6 CONFIDENTIAL Symbol Trcnt Value Unit Min Max 266 155 μs 155 266 μs 315 315 567 567 μs μs 315 567 μs 336 Remarks μs without RAM retention μs with RAM retention 667 MB9B360L_DS709-00007-1v0-E-DE1, April 25, 2014