227KB

The following document contains information on Cypress products.
FM4 Family
32-BIT Microcontroller
MB9B160L
DATA SHEET
Errata Sheet
Page
Item
Original document code: DS709-00008-1v0-E
Rev 1.0 April 25, 2014
32
I/O CIRCUIT
TYPE
Description
It should be added as indicated by the shading below.
Type
Circuit
Remarks
H
P-ch
N-ch
Digital output
・ CMOS level output
・ CMOS level hysteresis
input
・ With standby mode
control
・ IOH = -20.5 mA, IOL =
18.5 mA
Digital output
R
Digital input
Standby
mode
Control
Publication Number MB9B160L_DS709-00008-1v0-E-DE
CONFIDENTIAL
Revision 1.0
Issue Date April 25, 2014
E R R A T A
Page
33
Item
I/O CIRCUIT
TYPE
Description
It should be added as indicated by the shading below.
Type
Circuit
I
P-ch
P-ch
N-ch
R
2
CONFIDENTIAL
S H E E T
Remarks
・ CMOS level output
・ CMOS level hysteresis
input
・ 5V tolerant
Digital output ・ With standby mode
control
・ Pull-up resistor
: Approximately 50kΩ
Digital output
・ IOH = -4mA, IOL = 4mA
・ Available to control of
Pull-up resistor
PZR registers.
control
・
When this pin is used as
Digital input
an I2C pin, the digital
Standby mode
output P-ch transistor is
control
always off
MB9B160L_DS709-00008-1v0-E-DE1, April 25, 2014
E R R A T A
Page
54
S H E E T
Item
Pin Status
Description
“List of VBAT Domain Pin Status” should be corrected as indicated by the shading below.
VBAT pin status type
(Error)
INITX
input
state
Function
group
Device
internal
reset
state
TIMER mode,
RTC mode, or
STOP mode state
Power supply stable Power supply stable
INITX=0
INITX=1
‐
‐
S
selected
Setting
disabled
Setting
disabled
SPL=0
SPL=1
Maintain
previous
state
Internal
input fixed
at "0"
Hi-Z /
GPIO
selected
Setting
disabled
Setting
disabled
External sub
clock input
Maintain
previous
state
Maintain
Setting
disabled
selected
Setting
disabled
previous
state
T
Internal
input fixed
at "0"
Hi-Z /
Internal
input fixed
at "0"
Maintain
Maintain
oscillator
output pin
Power supply stable
Power supply
stable
INITX=1
INITX=1
previous
previous
SPL=0
GPIO
selected
Internal
input fixed
at "0"
GPIO
selected
Internal
input fixed
at "0"
Maintain
previous
state
Maintain
previous
state/When state/When
Hi-Z / Internal
oscillation oscillation
Internal
input
stops*,
stops*,
input
fixed
Hi-Z /
Hi-Z /
fixed
at "0"
at "0"
Internal
Internal
state/When
input fixed input fixed
input fixed
Hi-Z /
Sub crystal
Return from
Deep standby
mode state
INITX=1
Hi-Z /
GPIO
Deep standby
RTC mode
or
Deep standby
STOP mode state
at "0"
at "0"
oscillation
stops*,
Hi-Z/
Internal
at "0"
SPL=1
-
Hi-Z /
Internal
input fixed
at "0"
GPIO
selected
Hi-Z /
Internal
input fixed
GPIO
selected
at "0"
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state/When
oscillation
stops*,
Hi-Z/ Internal
input fixed
at "0"
Maintain
previous
state
Maintain
previous
state/When
oscillation
stops*,
Hi-Z/
Internal
input fixed
at "0"
*Oscillation is stopped at STOP mode and Deep standby STOP mode.
April 25, 2014, MB9B160L_DS709-00008-1v0-E-DE1
CONFIDENTIAL
3
E R R A T A
Page
Pinstatus
Description
(Correct)
VBAT pin status type
54
Item
S H E E T
S
INITX
input
state
Function
group
Device
internal
reset
state
TIMER mode,
RTC mode, or
STOP mode state
Power supply stable Power supply stable
INITX=0
INITX=1
Deep standby
RTC mode
or
Deep standby
STOP mode state
Return from
Deep standby
mode state
Power supply stable
Power supply
stable
INITX=1
INITX=1
INITX=1
‐
‐
SPL=0
SPL=1
SPL=0
Maintain
previous
state
Maintain
Maintain
previous
state
Maintain
Maintain
previous
state
Maintain
Maintain
previous
state
Maintain
Maintain
previous
state
Maintain
previous
state
External sub Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
clock input
previous
previous
previous
previous
previous
state
state
state
state
state
Maintain
Maintain
previous
previous
GPIO
selected
GPIO
selected
selected
T
Sub crystal
Maintain
Maintain
oscillator
previous
previous
output pin
state
state
state/When state/When
oscillation oscillation
stops,
stops,
Hi-Z*
Hi-Z*
Maintain
previous
SPL=1
Maintain previous
state
Maintain previous
state
Maintain previous
state
Maintain previous
state/When
state/When
oscillation stops,
oscillation stops,
Hi-Z*
Hi-Z*
-
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
*When The SOSCNTL bit in the WTOSCCNT Register is “0”, Sub crystal oscillator output pin is maintain
previous state.
When The SOSCNTL bit in the WTOSCCNT Register is “1”, Oscillation is stopped at STOP mode and Deep
standby STOP mode.
57
ELECTRICAL It should be corrected as indicated by the shading below.
CHARACTERIS
TICS
Parameter
Symbol
Conditions
Value
Min Max
Unit
Remarks
2.Recommended
Power supply voltage
VCC
2.7*3
5.5
V
Operating
*3: In between less than the minimum power supply voltage and low voltage reset/interrupt
Conditions
detection voltage or more, instruction execution and low voltage detection function by built-in
High-speed CR (including Main PLL is used) or built-in Low-speed CR is possible to operate
only.
4
CONFIDENTIAL
MB9B160L_DS709-00008-1v0-E-DE1, April 25, 2014
E R R A T A
Page
70
S H E E T
Item
Description
“(3) Built-in CR Oscillation Characteristics” should be corrected as indicated by the shading below.
ELECTRICAL
CHARACTERIS
・Built-in High-speed CR
TICS
4. AC
Characteristics
(VCC = 2.7V ~ 5.5V, VSS = 0V)
Parameter Symbol
Clock
frequency
FCRH
Value
Min Typ Max
Conditions
Tj = -20°C to + 105°C
Tj = - 40°C to + 125°C
3.92
3.88
4
4
4.08
4.12
Tj = - 40°C to + 125°C
3
4
5
Unit Remarks
When
trimming*1
MHz
When not
trimming
Frequency
stabilization tCRWT
30
μs *2
time
*1: In the case of using the values in CR trimming area of Flash memory at shipment for
frequency/temperature trimming.
*2: This is the time to stabilize the frequency of high-speed CR clock after setting trimming value
This period is able to use high-speed CR clock as source clock.
109
ELECTRICAL “Electrical Characteristics for the A/D Converter” should be added as indicated by the shading below.
CHARACTERIS
(VCC = AVCC = 2.7Vto5.5V, VSS = AVSS = 0V)
TICS
6. 12-bit D/A
Converter
tc20
tc100
Min
0.56
2.79
Value
Typ
0.69
3.42
INL
- 16
-
+ 16 LSB
- 0.98
-
+ 1.5 LSB
-
-
10.0 mV
- 20.0
-
+ 1.4 mV
3.10
2.0
3.80
-
4.50 kΩ
MΩ
260
330
410
μA
400
519
620
μA
-
-
14
μA
Parameter
Symbol
Resolution
Conversion time
Integral
Nonlinearity*
Differential
Nonlinearity*
DNL
Output voltage
offset
VOFF
Analog output
impedance
RO
Power supply
current*
IDDA
IDSA
Pin name
DAx
AVCC
Max
12
0.81
4.06
Unit
Remarks
bit
μs Load 20pF
μs Load 100pF
When setting
0x000
When setting
0xFFF
D/A operation
When D/A stop
D/A operation
AVCC=3.3V
D/A operation
AVCC=5.0V
When D/A stop
*: During no load
April 25, 2014, MB9B160L_DS709-00008-1v0-E-DE1
CONFIDENTIAL
5
E R R A T A
Page
112
Item
S H E E T
Description
ELECTRICAL “Recovery count time” of “(1) Recovery cause: Interrupt/WKUP” should be corrected as indicated by the
CHARACTERIS shading below.
TICS
(Error)
10. Standby
Recovery Time
Parameter
Sub timer mode
RTC mode
Stop mode
(High-speed CR
/Main/PLL run mode
return)
RTC mode
Stop mode
(Low-speed CR/sub run
mode return)
Symbol
Ticnt
Deep standby RTC mode
with RAM retention
Deep standby stop mode
with RAM retention
Value
Min
Max
Unit
Remarks
881
1136
μs
270
581
μs
240
480
μs
308
667
μs
without RAM
retention
308
667
μs
with RAM
retention
(Correct)
Parameter
Sub timer mode
RTC mode
Stop mode
(High-speed CR
/Main/PLL run mode
return)
RTC mode
Stop mode
(Low-speed CR/sub run
mode return)
Deep standby RTC mode
with RAM retention
Deep standby stop mode
with RAM retention
6
CONFIDENTIAL
Symbol
Ticnt
Value
Min
Max
Unit
Remarks
896
1136
μs
316
581
μs
270
540
μs
365
667
μs
without RAM
retention
365
667
μs
with RAM
retention
MB9B160L_DS709-00008-1v0-E-DE1, April 25, 2014
E R R A T A
Page
114
S H E E T
Item
Description
ELECTRICAL “Recovery count time” of “(2) Recovery cause: Reset” should be corrected as indicated by the shading
CHARACTERIS below.
TICS
(Error)
10. Standby
Recovery Time
Parameter
Sleep mode
High-speed CR Timer mode
Main Timer mode
PLL Timer mode
Low-speed CR timer mode
Sub timer mode
RTC mode
Stop mode
Symbol
Trcnt
Deep standby RTC mode
with RAM retention
Deep standby stop mode
with RAM retention
Value
Min
Max
266
116
Unit
Remarks
μs
116
266
μs
258
258
567
567
μs
μs
258
567
μs
308
697
μs
without RAM
retention
308
697
μs
with RAM
retention
(Correct)
Parameter
Sleep mode
High-speed CR Timer mode
Main Timer mode
PLL Timer mode
Low-speed CR timer mode
Sub timer mode
RTC mode
Stop mode
Deep standby RTC mode
with RAM retention
Deep standby stop mode
with RAM retention
April 25, 2014, MB9B160L_DS709-00008-1v0-E-DE1
CONFIDENTIAL
Symbol
Trcnt
Value
Min
Max
266
155
Unit
μs
155
266
μs
315
315
567
567
μs
μs
315
567
μs
336
Remarks
μs
without RAM
retention
μs
with RAM
retention
667
7