MB9B360R Series 32-bit ARM® Cortex®-M4F based Microcontroller Data Sheet Errata Sheet Page Item Description Original document code: DS709-00003-1v0-E Rev. 1.0 January 9, 2014 74 ELECTRICAL It should be corrected as indicated by the shading below. CHARACTERIS TICS Parameter 2.Recommended Operating Conditions Power supply voltage Symbol Conditions VCC - Value Min Max 2.7 Unit 5.5 Remarks V Analog reference voltage AVRH *4 AVCC V *4 :The minimum value of Analog reference voltage depends on the value of compare clock cycle (Tcck). See "5. 12-bit A/D Converter" for the details. See the description of the same item on Rev. 2.0 (P.3). 146 ELECTRICAL “Electrical Characteristics for the A/D Converter” should be corrected as indicated by the shading below. CHARACTERIS TICS (Error) 5. 12-bit A/D Converter Parameter Symbol Pin name Reference voltage AVRH - Min Value Typ Max 2.7 - AVCC Min Value Typ Max 4.5 - AVCC Unit Remarks V (Correct) Rev. 2.0 2 Parameter Symbol Pin name Reference voltage AVRH - 2.7 - AVCC Unit Remarks Tcck < 50ns V Tcck ≥ 50ns April 25, 2014 FEATURES “●32-bit ARM Cortex-M4F Core “should be corrected as indicated by the shading below. (Error) ・ Processor version: r2p1 (Correct) ・ Processor version: r0p1 Publication Number MB9B360R_DS709-00003-1v0-E-DE CONFIDENTIAL Revision 3.0 Issue Date September 24, 2015 E R R A T A Page Item 49 I/O CIRCUIT TYPE Description It should be added as indicated by the shading below. Type Circuit I P-ch P-ch N-ch R 71 Pin Status S H E E T Remarks ・ CMOS level output ・ CMOS level hysteresis input Digital output ・ 5V tolerant ・ With standby mode control ・ Pull-up resistor Digital output : Approximately 50kΩ ・ IOH = -4mA, IOL = 4mA ・ Available to control of Pull-up resistor PZR registers. control Digital input Standby mode control “List of VBAT Domain Pin Status” should be corrected as indicated by the shading below. VBAT pin status type (Error) Function group Deep standby RTC mode or Deep standby STOP mode state Return from Deep standby mode state Power supply stable Power supply stable Power supply stable Power supply stable INITX=0 ‐ INITX=1 SPL=0 SPL=1 INITX=1 - INITX input state Device internal reset state INITX=1 ‐ TIMER mode, RTC mode, or STOP mode state INITX=1 SPL=0 SPL=1 Hi-Z / S GPIO selected Setting disabled Setting disabled Maintain previous state Internal input fixed at "0" Hi-Z / GPIO selected Setting disabled Setting disabled External sub clock input Maintain previous state Maintain Setting disabled selected Setting disabled previous state T Sub crystal oscillator output pin Internal input fixed at "0" Hi-Z / Internal input fixed at "0" GPIO selected Internal input fixed at "0" GPIO selected Internal input fixed at "0" Maintain previous state Maintain Maintain Maintain previous previous previous Hi-Z / state/When state/When Hi-Z / Internal oscillation oscillation input stops*, stops*, input fixed Hi-Z / Hi-Z / fixed at "0" at "0" Internal Internal state/When Internal oscillation input fixed input fixed input fixed at "0" at "0" stops*, Hi-Z/ Internal at "0" Hi-Z / Internal input fixed at "0" GPIO selected Hi-Z / Internal input fixed GPIO selected at "0" Hi-Z / Internal input fixed Maintain previous state at "0" Maintain previous state/When oscillation stops*, Hi-Z/ Internal input fixed at "0" Maintain previous state/When oscillation stops*, Hi-Z/ Internal input fixed at "0" *Oscillation is stopped at STOP mode and Deep standby STOP mode. 2 CONFIDENTIAL MB9B360R_DS709-00003-1v0-E-DE3, September 24, 2015 E R R A T A Item 71 Pin Status Description (Correct) VBAT pin status type Page S H E E T S TIMER mode, RTC mode, or STOP mode state Deep standby RTC mode or Deep standby STOP mode state Return from Deep standby mode state Power supply stable Power supply stable Power supply stable Power supply stable INITX=0 ‐ INITX=1 ‐ INITX=1 SPL=0 SPL=1 INITX=1 SPL=0 SPL=1 Maintain previous state Maintain Maintain previous state Maintain Maintain previous state Maintain Maintain previous state Maintain Maintain previous state Maintain Maintain previous state Maintain previous state External sub Maintain previous state Maintain previous state Maintain previous state Maintain previous state Maintain previous state Maintain clock input previous previous previous previous previous previous state state state state state state Function group GPIO selected GPIO INITX input state selected selected Device internal reset state T Maintain Sub crystal Maintain Maintain oscillator previous previous output pin state state Maintain previous state/When previous state/When Maintain previous state/When INITX=1 - Maintain previous state Maintain previous state Maintain previous state Maintain previous state/When Maintain previous oscillation oscillation oscillation stops, oscillation stops, stops, stops, Hi-Z* Hi-Z* Hi-Z* Hi-Z* state *When The SOSCNTL bit in the WTOSCCNT Register is “0”, Sub crystal oscillator output pin is maintain previous state. When The SOSCNTL bit in the WTOSCCNT Register is “1”, Oscillation is stopped at STOP mode and Deep standby STOP mode. 74 ELECTRICAL It should be corrected as indicated by the shading below. CHARACTERIS TICS 2.Recommended Operating Conditions Parameter Power supply voltage Symbol Conditions VCC - Value Min Max 2.7*5 5.5 Unit Remarks V Analog reference voltage AVRH *4 AVCC V *4 :The minimum value of Analog reference voltage depends on the value of compare clock cycle (Tcck). See "5. 12-bit A/D Converter" for the details. *5：In between less than the minimum power supply voltage and low voltage reset/interrupt detection voltage or more, instruction execution and low voltage detection function by built-in High-speed CR(including Main PLL is used) or built-in Low-speed CR is possible to operate only. September 24, 2015, MB9B360R_DS709-00003-1v0-E-DE3 CONFIDENTIAL 3 E R R A T A Page 87 Item S H E E T Description “(3) Built-in CR Oscillation Characteristics” should be corrected as indicated by the shading below. ELECTRICAL CHARACTERIS ・ Built-in High-speed CR TICS 4. AC Characteristics Parameter Symbol (VCC = 2.7V to 5.5V, VSS = 0V) Value Min Typ Max Conditions Unit Remarks Tj = -20°C to + 105°C 3.92 4 4.08 Clock When FCRH frequency trimming*1 Tj = - 40°C to + 125°C 3.88 4 4.12 MHz Clock When not FCRH Tj = - 40°C to + 125°C 3 4 5 frequency trimming Frequency stabilization tCRWT 30 μS *2 time *1: In the case of using the values in CR trimming area of Flash memory at shipment for frequency/temperature trimming. *2: This is the time to stabilize the frequency of high-speed CR clock after setting trimming value. This period is able to use high-speed CR clock as source clock. 149 ELECTRICAL “Electrical Characteristics for the A/D Converter” should be added as indicated by the shading below. CHARACTERIS TICS (VCC = AVCC = 2.7Vto5.5V, VSS = AVSS = 0V) 6. 12-bit D/A Converter Parameter Resolution Conversion time Integral Nonlinearity* Differential Nonlinearity* Symbol Pin name tc20 tc100 INL - 16 - + 16 LSB - 0.98 - + 1.5 LSB - - 10.0 mV - 20.0 - + 1.4 mV 3.10 2.0 3.80 - 4.50 - kΩ MΩ 260 330 410 μA 400 510 620 μA - - 14 μA DNL VOFF Analog output impedance RO IDDA IDSA DAx AVCC Max 12 0.81 4.06 Unit Min 0.56 2.79 Output voltage offset Power supply current* Value Typ 0.69 3.42 Remarks bit μs Load 20pF μs Load 100pF When setting 0x000 When setting 0xFFF D/A operation When D/A stop D/A operation AVCC=3.3V D/A operation AVCC=5.0V When D/A stop *: During no load 4 CONFIDENTIAL MB9B360R_DS709-00003-1v0-E-DE3, September 24, 2015 E R R A T A Page 156 S H E E T Item Description ELECTRICAL “Recovery count time” of “(1) Recovery cause: Interrupt/WKUP” should be corrected as indicated by the CHARACTERIS shading below. TICS (Error) 11. Standby Value Recovery Time Parameter Symbol Unit Remarks Sub timer mode RTC mode Stop mode (High-speed CR /Main/PLL run mode return) RTC mode Stop mode (Low-speed CR/sub run mode return) Ticnt Deep standby RTC mode with RAM retention Deep standby stop mode with RAM retention Min Max 881 1136 μs 270 581 μs 240 480 μs 308 667 μs without RAM retention 308 667 μs with RAM retention (Correct) Parameter Sub timer mode RTC mode Stop mode (High-speed CR /Main/PLL run mode return) RTC mode Stop mode (Low-speed CR/sub run mode return) Deep standby RTC mode with RAM retention Deep standby stop mode with RAM retention September 24, 2015, MB9B360R_DS709-00003-1v0-E-DE3 CONFIDENTIAL Symbol Ticnt Value Min Max Unit Remarks 896 1136 μs 316 581 μs 270 540 μs 365 667 μs without RAM retention 365 667 μs with RAM retention 5 E R R A T A Page 158 Item S H E E T Description ELECTRICAL “Recovery count time” of “(2) Recovery cause: Reset” should be corrected as indicated by the shading CHARACTERIS below. TICS (Error) 11. Standby Value Recovery Time Parameter Symbol Unit Remarks Sleep mode High-speed CR Timer mode Main Timer mode PLL Timer mode Low-speed CR timer mode Sub timer mode RTC mode Stop mode Trcnt Deep standby RTC mode with RAM retention Deep standby stop mode with RAM retention Min 111 Max 267 μs 111 267 μs 258 258 569 569 μs μs 258 569 μs μs 308 669 μs without RAM retention with RAM retention (Correct) Parameter Sleep mode High-speed CR Timer mode Main Timer mode PLL Timer mode Low-speed CR timer mode Sub timer mode RTC mode Stop mode Deep standby RTC mode with RAM retention Deep standby stop mode with RAM retention 6 CONFIDENTIAL Symbol Trcnt Value Min Max 266 155 Unit μs 155 266 μs 315 315 567 567 μs μs 315 567 μs 336 Remarks μs without RAM retention μs with RAM retention 667 MB9B360R_DS709-00003-1v0-E-DE3, September 24, 2015 E R R A T A Page Rev. 3.0 157 S H E E T Item Description September 24, 2015 14.5 12-bit A/D Converter Table (Sampling time, State transition time to operation permission) should be corrected as indicated by shading below. (Error) Parameter Sampling time Compare clock 3 cycle* Symbol tS Value Pin Name Min Typ *2 - - tCCK - tSTT - Max 10 *2 - 25 - Unit μs Remarks AVCC ≥ 4.5V AVCC < 4.5V 1000 ns 50 - 1000 1.0 - - AVCC ≥ 4.5V AVCC < 4.5V State transition time to operation μs permission (Correct) Parameter Sampling time Compare clock 3 cycle* Symbol Value Pin Name tS - tCCK - tSTT - Min Typ 0.15 - 0.3 - 25 - Max 10 Unit μs Remarks AVCC ≥ 4.5V AVCC < 4.5V 1000 ns 50 - 1000 - - 1.0 AVCC ≥ 4.5V AVCC < 4.5V State transition time to operation μs permission September 24, 2015, MB9B360R_DS709-00003-1v0-E-DE3 CONFIDENTIAL 7