Datasheet

Photomicrosensor (Transmissive)
EE-SX1131
Be sure to read Precautions on page 25.
■ Dimensions
■ Features
Note: All units are in millimeters unless otherwise indicated.
•
•
•
•
Ultra-compact with a 5-mm-wide sensor and a 2-mm-wide slot.
PCB surface mounting type.
High resolution with a 0.3-mm-wide aperture.
Dual-channel output.
■ Absolute Maximum Ratings (Ta = 25°C)
Item
Emitter
Optical
axis
Detector
Cross section AA
Recommended Soldering Pattern
Internal Circuit
Ambient temperature
Terminal No.
Name
A
Anode
NC
K
C
E1
E2
Not connected.
Cathode
Collector
Emitter 1
Emitter 2
Unless otherwise specified, the
tolerances are ±0.15 mm.
Symbol
Rated value
Forward current
IF
25 mA
(see note 1)
Pulse forward current
IFP
100 mA
(see note 2)
Reverse voltage
VR
5V
Collector–Emitter
voltage
VCEO
20 V
Emitter–Collector
voltage
VECO
5V
Collector current
IC
20 mA
Collector dissipation
PC
75 mW
(see note 1)
Operating
Topr
–30°C to 85°C
Storage
Tstg
–40°C to 90°C
Reflow soldering
Tsol
255°C
(see note 3)
Manual soldering
Tsol
350°C
(see note 3)
Note: 1. Refer to the temperature rating chart if the ambient temperature exceeds 25°C.
2. Duty: 1/100; Pulse width: 0.1 ms
3. Complete soldering within 10 seconds for reflow soldering
and within 3 seconds for manual soldering.
■ Electrical and Optical Characteristics (Ta = 25°C)
Item
Emitter
Detector
Symbol
Value
Condition
Forward voltage
VF
1.1 V typ., 1.3 V max.
IF = 5 mA
Reverse current
IR
10 μA max.
VR = 5 V
Peak emission wavelength
λP
940 nm typ.
IF = 20 mA
Light current
IL1/IL2
50 μA min., 150 μA typ.,
500 μA max.
IF = 5 mA, VCE = 5 V
Dark current
ID
100 nA max.
VCE = 10 V, 0 lx
Leakage current
ILEAK
---
---
Collector–Emitter saturated voltage
VCE (sat)
0.1 V typ., 0.4 V max.
IF = 20 mA, IL = 50 μA
Peak spectral sensitivity wavelength
λP
900 nm typ.
---
Rising time
tr
10 μs typ.
VCC = 5 V, RL = 1 kΩ,
IL = 100 μA
Falling time
tf
10 μs typ.
VCC = 5 V, RL = 1 kΩ,
IL = 100 μA
78
EE-SX1131 Photomicrosensor (Transmissive)
■ Engineering Data
Ambient temperature Ta (°C)
IF = 10 mA
IF = 5 mA
Light current IL (μA)
Dark Current vs. Ambient TemRelative Light Current vs. Ambient
Temperature Characteristics (Typical) perature Characteristics (Typical)
Collector−Emitter voltage VCE (V)
IF = 5 mA
VCE = 5 V
Relative light current IL (%)
Response time tr, tf (μs)
Load resistance RL (kΩ)
VCE = 10 V
VCE = 2 V
Ambient temperature Ta (°C)
Ambient temperature Ta (°C)
Response Time vs. Load Resistance Sensing Position Characteristics
(Typical)
Characteristics (Typical)
VCC = 5 V
Ta = 25°C
Ta = 25°C
VCE = 5 V
Forward current IF (mA)
Dark current ID (nA)
Light current IL (μA)
Ta = 25°C
Ta = 25°C
Forward voltage VF (V)
Relative light current IL (%)
Light Current vs. Collector−Emitter
Voltage Characteristics (Typical)
Light Current vs. Forward Current
Characteristics (Typical)
IF = 5 mA
VCE = 5 V
Distance d (mm)
Sensing Position Characteristics
(Typical)
Relative light current IL (%)
Forward current IF (mA)
Forward current IF (mA)
Forward Current vs. Forward
Voltage Characteristics (Typical)
Collector dissipation PC (mW)
Forward Current vs. Collector
Dissipation Temperature Rating
IF = 5 mA
VCE = 5 V
Distance d (mm)
Response Time Measurement
Circuit
Input
Output
90 %
10 %
Input
Output
EE-SX1131 Photomicrosensor (Transmissive)
79
Unit: mm (inch)
■ Tape and Reel
Reel
21±0.8 dia.
2±0.5
13±
0.5 dia.
330±2 dia.
80±1 dia.
Product name
Quantity
Lot number
12.4+2
0
18.4 max.
Tape
1.5 dia.
Tape configuration
Terminating part
(40 mm min.)
Parts mounted
Pull-out direction
Tape quantity
2,000 pcs./reel
80
EE-SX1131 Photomicrosensor (Transmissive)
Leading part
(400 mm min.)
Empty
(40 mm min.)
Precautions
■ Soldering Information
Reflow soldering
• The following soldering paste is recommended:
Melting temperature: 216 to 220°C
Composition: Sn 3.5 Ag 0.75 Cu
• The recommended thickness of the metal mask for screen printing is between 0.2 and 0.25 mm.
• Set the reflow oven so that the temperature profile shown in the following chart is obtained for the upper surface of the product being soldered.
Temperature
1 to 5°C/s
260°C max.
255°C max.
230°C max.
1 to 5°C/s
150 to 180°C
120 sec
10 sec max.
40 sec max.
Time
Manual soldering
•
•
•
•
Use ”Sn 60” (60% tin and 40% lead) or solder with silver content.
Use a soldering iron of less than 25 W, and keep the temperature of the iron tip at 300°C or below.
Solder each point for a maximum of three seconds.
After soldering, allow the product to return to room temperature before handling it.
Storage
To protect the product from the effects of humidity until the package is opened, dry-box storage is recommended. If this is not possible, store the
product under the following conditions:
Temperature: 10 to 30°C
Humidity: 60% max.
The product is packed in a humidity-proof envelope. Reflow soldering must be done within 48 hours after opening the envelope, during which time
the product must be stored under 30°C at 80% maximum humidity.
If it is necessary to store the product after opening the envelope, use dry-box storage or reseal the envelope.
Baking
If a product has remained packed in a humidity-proof envelope for six months or more, or if more than 48 hours have lapsed since the envelope
was opened, bake the product under the following conditions before use:
Reel: 60°C for 24 hours or more
Bulk: 80°C for 4 hours or more
EE-SX1131 Photomicrosensor (Transmissive)
81