POWR1014A Breakout Board Evaluation Kit User’s Guide February 2012 Revision: EB64_01.1 POWR1014A Breakout Board Evaluation Kit User’s Guide Introduction Thank you for choosing the Lattice Semiconductor POWR1014A Breakout Board Evaluation Kit! Lattice Semiconductor’s Power Manager II ispPAC®-POWR1014A device simplifies power supply design by integrating the analog and digital functions of power supply management (sequencing, monitoring, measuring, and reset generation) into a single device. This device provides designers with a rich set of features: precision comparators with a built-in voltage reference, 10-bit ADC for I2C monitoring, MOSFET drivers and a programmable logic device (PLD) for sequencing and supervisory logic functions or reset control. Configuration for all subsystems in the POWR1014A device is stored in non-volatile E2CMOS® memory. Programming is performed via a USB cable. Along with the board and accessories, this kit includes a pre-loaded demonstration design. The on-board POWR1014A device can easily be reprogrammed for customized designs. Note: Static electricity can severely shorten the lifespan of electronic components. See the Storage and Handling section of this document for handling and storage tips. Features The ispPAC-POWR1014A Breakout Board Evaluation Kit includes: • ispPAC-POWR1014A Breakout Board – The board is a 3” x 3” form factor that features the following on-board components and circuits: – ispPAC-POWR1014A-02TN48I Power Manager II device – USB mini-B connector for power and programming – Nine LEDs – 4x15 prototype area – Two 2x20 expansion header landings for general I/O, JTAG, and external power – 1x8 expansion header landing for JTAG – 3.3V supply rail • Pre-loaded Demo – The kit includes a pre-loaded counter design that highlights the use of the embedded POWR1014A oscillator and programmable I/Os configured for LED drive. • USB Connector Cable – The board is powered from the USB mini-B socket when connected to a host PC. The USB channel also provides a programming interface to the POWR1014A JTAG port. • Lattice Breakout Board Evaluation Kits Web Page – Visit www.latticesemi.com/breakoutboards for the latest documentation (including this guide), demo designs, and drivers for the kit. The content of this user’s guide includes demo operation, programming instructions, top-level functional descriptions of the POWR1014A Breakout Board, and a complete set of schematics. Input/Output Connectors are provided for key functions and test points on this evaluation board, as shown in Figure 1. The USB programming cable is connected to the USB port (J2) shown on the bottom of the figure. Access to the ispPOWR1014A device’s I/O pins are available as shown along the right and left edges of the assembly, where two 2x20 blocks of pads (J3 and J6) support the attachment of test probes or a ribbon-cable connector. An array of 60 prototype holes for interfacing is shown at the top of the figure. Several LEDs on the evaluation board are provided to indicate proper function and as aids to debugging. The green LED (D9) indicates that the on-board 3.3V supply (derived from the input USB voltage) is powered up. Eight red LEDs (D1 through D8) are provided to demonstrate control of digital outputs OUT7 through OUT14 so that a user may easily view the progress of Sequence, Monitor, Reset programs run on the evaluation board. 2 POWR1014A Breakout Board Evaluation Kit User’s Guide Figure 1. POWR1014A Breakout Board, Top Side LED Array 4x15 Prototype Area 20-Pin Header (J3) 20-Pin Header (J6) USB Interface (J2) JTAG Header Landing (J1) Storage and Handling Static electricity can shorten the lifespan of electronic components. Please observe these tips to prevent damage that could occur from electro-static discharge: • Use anti-static precautions such as operating on an anti-static mat and wearing an anti-static wrist-band. • Store the evaluation board in the packaging provided. • Touch a metal USB housing to equalize voltage potential between you and the board. Software Requirements The POWR1014A Breakout Board uses an FTDI USB interface device that requires USB drivers contained in the following software to communicate properly. Initial manual testing (Quick Start) using the computer USB power maybe accomplished before loading the software drivers. For manual testing only, plug the board into the computer USB port and “cancel” when requested to install new hardware. If the incorrect drivers are installed by Windows they may require removal before the FTDI USB drivers can be loaded and the POWR1014A Breakout Board can be recognized by the computer. • PAC-Designer design software • ispVM™ System device programming software • FTDI USB drivers 3 POWR1014A Breakout Board Evaluation Kit User’s Guide POWR1014A Device This board features the Power Manager II ispPAC-POWR1014A general-purpose power-supply monitor and sequence controller, incorporating both in-system programmable logic and in-system programmable analog functions implemented in non-volatile E2CMOS technology. A complete description of this device can be found in the ispPAC-POWR1014/A Data Sheet. Demonstration Design Lattice provides a pre-programmed demo to illustrate basic operation of the POWR1014A device. The program demonstrates sequencing of the output pins Out4 through Out14. Using an internal timer the program alternates the POWR1014A outputs, illuminating LEDs D1, D3, D5 and D7 then LEDs D2, D4, D6 and D8. Note: To restore the factory default demo or program it with other Lattice-supplied examples see the Download Demo or Create New Designs section of this document. Run the Demonstration Design USB Cable Power Connection Download USB Hardware Drivers: Communication with the POWR1014A Breakout Board with a PC via the USB cable will require the USB hardware drivers contained in the Software Requirements section. Loading these drivers enables the computer to recognize and program the POWR1014A Breakout Board. To load these USB drivers, use one of the following methods: Preferred Installation: 1. Run ispVM System and choose Install/Uninstall LSC USB/Parallel Port Driver from the ispTools tab. Optional Installation: 1. Connect the USB cable from a USB port on your PC to the board’s USB mini-B socket (J2). After connection is made, a green Power LED (D9) will light up indicating the board is powered on. 2. If you are prompted, “Windows may connect to Windows Update” select No, not this time from available options and click Next to proceed with the installation. Choose the Install from specific location (Advanced) option and click Next. 3. Browse to the FTDI USB Drivers listed in the Software Requirements section. Search for the best driver in these locations and click the Browse button to browse to the Windows driver folder created in the Download Windows USB Hardware Drivers section. Select the CDM 2.04.06 WHQL Certified folder and click OK. 4. Click Next. A screen will display as Windows copies the required driver files. Windows will display a message indicating that the installation was successful. 5. Click Finish to install the USB driver. Reprogramming Designs The support demo is preprogrammed into the POWR1014A. It may be desirable to reload the original demo program after any design modification. Lattice distributes the source (JED) and schematic (PAC) files for demonstration designs compatible with the POWR1014A Breakout Board. Refreshing the programming for U4 POWR1014A will require the demo JEDEC file. This is available directly as a .jed file or can be compiled from the .pac files using PAC-Designer. The .jed files are then loaded into U4 via the USB cable using ispVM software. Programming Devices with ispVM To restore a POWR1014A Breakout Board to factory settings or load an alternative demo design, use the procedures in this section. 4 POWR1014A Breakout Board Evaluation Kit User’s Guide For more information see AN6062, Using ispVM System to Program ispPAC Devices. 1. Connect the board to a host PC using the USB port or JTAG header connection. 2. Follow the USB Cable Interface procedure below to program the evaluation board. USB Cable Interface Connection: The POWR1014A Breakout Board is equipped with a built-in USB-based programming circuit. This consists of a USB PHY and a USB connector. When the board is connected to a PC with a USB cable, it is recognized by the ispVM System software as a “USB Download Cable”. The POWR1014A can then be scanned and programmed using the ispVM System software. Download Demo or Create New Designs 1. Browse to the POWR1014A Breakout Board design files. 2. Extract the contents of PAC_POWR1014A_BREAKOUTBOARD.zip to an accessible location on your hard drive. The demo design directory (PAC_POWR1014A_BREAKOUTBOARD<demo>) is unpacked. Demo Directory PAC_POWR1014A_BLINKER PAC_POWER1014A_BLINKER.JED PAC_POWR1014A_BREAKOUTBOARD Create or Modify the <demo>.jed Design by compiling a PAC-Designer using <demo>.PAC file: Use the procedure below to recompile the demo project for the POWR1014A Breakout Board or modify for a custom design. 1. Run PAC-Designer. 2. From the File tab open either the <demo>.PAC project file from the Download Demo Designs section or other >.PAC file if implementing a custom design. 3. Modification of the I/Os or change of sequencing for custom designs can be done at this step. 4. From the schematic block diagram, double-click the Sequence Controller block. The LogiBuilder interface appears. Table 1. Demo Design Sequencing Program (for Reference Only) Step Instruction Outputs Int. Comment 0 Begin Startup Sequence 0 POWR1014A reset OUT4 = 1, OUT5 = 0, OUT6 = 1, OUT7 = 0, OUT8 = 0, OUT9 = 0, OUT14 = 0, 0 Initializes outputs 1 0 Set outputs 4 through 14, 0 = Hi Z, 1 = Ground, then waits for power good 0 3 OUT4 = 1, OUT5 = 0, OUT6 = 1, OUT7 = 0, OUT8 = 1, OUT9 = 0, OUT10 = 1, OUT11 = 0, OUT12 = 1, OUT13 = 0, OUT14 = 1, Alternate output settings for OUT4 throughOUT14 4 Wait for 524.29ms using timer 1 0 Wait 0.5 sec OUT3 = 1, OUT4 = 0, OUT5 = 1, OUT6 = 0, OUT7 = 1, OUT8 = 0, OUT9 = 1, OUT10 = 0, OUT11 = 1, OUT12 = 0, OUT13 = 1, OUT14 = 0, 0 5 Alternate outputs OUT4 through OUT14 6 Wait for 524.29ms using Timer 1 0 Wait 0.5 sec Wait for AGOOD 2 OUT4 = 0, OUT5 = 1, OUT6 = 0, OUT7 = 1, OUT8 = 0, OUT9 = 1, OUT10 = 0, OUT11 = 1, OUT12 = 0, OUT13 = 1, OUT14 = 0, 5 POWR1014A Breakout Board Evaluation Kit User’s Guide Table 1. Demo Design Sequencing Program (for Reference Only) Step Instruction Outputs Int. Comment Go to Step 3 0 Enter loop to alter sequence of OUT4 through OUT14. Flashes odd then even LEDs. 8 Begin shut-down sequence 0 9 Halt (end-of-program) 0 7 5. Choose Tools > Compile LogiBuilder Design. After a few moments the JEDEC programming file is output. Click OK. 6. From the toolbar launch JED to download and save the file. Note: PAC-Designer may not recognize files that have certain characters such as spaces or periods in the directory path. To program the device using a <demo>.jed file: 1. From the Start menu run ispVM System. ispVM appears. 2. Choose Options > Cable and I/O Port Setup... The Cable and I/O Port Setup dialog appears. 3. Make the following selections: Cable Type: USB2 Port Setting: FTUSB-0 Click OK. 4. Choose ispTools > Scan Chain. The New Scan Configuration Setup window appears. The POWR1014A appears in the device list. 5. Highlight the POWR1014A, right-click and choose Edit Device... The Device Information dialog appears. 6. From the Set Device Operations section, click the Browse button. The Open Data File dialog appears. 7. Download the .jed file either downloaded from the Lattice web site or file compiled using PAC-Designer by browsing to the <Demo Dir>\project folder, selecting <Demo>.jed, and clicking OK. 8. Select the device to be programmed by highlighting and then right-clicking and choose Set Device Operations. From the Operation list choose Flash Erase, Program, Verify. 9. From the toolbar select Go to program device Programming requires about 20-40 seconds. A small timer window will appear to show elapsed programming time. At the end of programming, the configuration setup window should show a “PASS” in the Status column. 6 POWR1014A Breakout Board Evaluation Kit User’s Guide POWR1014A Breakout Board This section describes the features of the ispPOWR1014A Breakout board detail. POWR1014A The ispPAC-POWR1014A-02TN48I in the 7x7mm 48-pin TQFP package has the ability to monitor 10 analog inputs and provides 14 digital outputs. Two of the outputs can be configured to provide 6V to 12V MOSFET gate drive. Table 2. POWR1014A Interface Reference Item Description Reference designator U4 Part number POWR1014A Manufacturer Lattice Semiconductor Web site www.latticesemi.com JTAG Interface Circuits For power and programming, a FTDI USB UART/FIFO IC converter provides a communication interface between a PC host and the JTAG programming chain of the POWR1014A Breakout Board. The USB 5V supply is also used as a source for the 3.3V supply rail. A USB mini-B socket is provided for the USB connector cable. Table 3. JTAG Interface Reference Item Description Reference designator U2 Part number FT2232H Manufacturer Future Technology Devices International (FTDI) Web site www.ftdichip.com Table 4. JTAG Programming Pin Information Description POWR1014A Pin Test Data Output Pin 21 TDO Test Data Output — Test Data Input Pin 18 TDI Test Mode Select Pin 16 TMS Test Clock Pin 22 TCK LEDs A green LED (D9) is used to indicate USB 5V power and red LEDs (D1 to D8) are used to show the status of the outputs. Table 5. User LEDs Reference Item Description Reference designators D1 through D9 Part number LTST-C190KGKT and LTST-C190KRKT Manufacturer Lite-On It Corporation Web site www.liteonit.com 7 POWR1014A Breakout Board Evaluation Kit User’s Guide Power Supply 3.3V supply rail is converted from the USB 5V interface by a linear regulator U1 when the board is connected to a host PC. Test Points The ability to program the POWR1014A without enabling the device I/Os can be accomplished by powering the VCCPROG only. After programming, VCCPROG should be left open and VCCA and VCCD should be powered for normal operation. TP1 provides access to VCCPROG. See Appendix A. Schematics for more details: • TP1, VCCPROG USB Programming and Debug Interface The USB mini-B socket of the POWR1014A Breakout Board serves as the programming and debug interface. JTAG Programming For JTAG programming a preprogrammed USB PHY peripheral controller is provided on the board to serve as the programming interface to the POWR1014A. Programming requires ispVM System software. Mechanical Specifications Dimensions: 3 in. [L] x 3 in. [W] x 1/2 in. [H] Environmental Requirements The POWR1014A Breakout Board must be stored between -40° C and 100° C. The recommended operating temperature is between 0° C and 90° C. The board can be damaged without proper anti-static handling. Glossary LED: Light Emitting Diode. RoHS: Restriction of Hazardous Substances Directive. USB: Universal Serial Bus. FTDI: Future Technology Devices International Ltd. Troubleshooting Use the tips in this section to diagnose problems with the POWR1014A Breakout Board. LEDs Do Not Flash If power is applied (LED D9 illuminated) but LEDs D1 through D8 do not flash according to the preprogrammed counter demonstration then it is likely the board has been reprogrammed with a new design. Follow the directions in the Demonstration Design section to restore the factory default. USB Cable Not Detected If ispVM System cannot detect the USB2 cable type programming interface to the board, the incorrect USB driver may have been installed. This usually occurs if you attach the board to your PC prior to installing the USB driver or ispVM System software. 8 POWR1014A Breakout Board Evaluation Kit User’s Guide To correct a USB driver installation: 1. Start ispVM and choose Options > Cable and I/O Port Setup. The Cable and I/O Port Setup Dialog appears. 2. Click the Troubleshooting the USB Driver Installation Guide link. The Troubleshooting the USB Driver Installation Guide document appears in your system’s PDF file reader. 3. Follow the instructions in the guide to install the Lattice USB driver. Determine the Source of a Pre-Programmed Device You may receive your POWR1014A Breakout board after it has been reprogrammed by someone else. To restore the board to the factory default, see the Download Demo or Create New Designs section for details on downloading and reprogramming the device. You can also determine which demo design is currently programmed onto the board by comparing the JEDEC checksums against of the programming file with what is read from the programmed device. To compare JEDEC file checksum: 1. Connect the POWR1014A Breakout Board to a host PC using the USB port. 2. Start ispVM and choose ispTools > Scan. The device appears in the Device List. 3. Double-click the device row. The Device Information dialog appears. 4. Click the Browse button. The Save as Data File dialog appears. 5. Specify a new JEDEC Data File name and click the Save button. 6. From the Operation list choose Read and Save JEDEC and click OK. 7. Choose Project > Download. ispVM reads the contents from the device and writes the results to the JEDEC file specified. Open the JEDEC file into a text editor and page to the bottom of the file. Note the hexadecimal checksum at the line above the User Electronic Data note line. Compare this value against the checksum of the original JEDEC demo programming files. Ordering Information Description POWR1014A Breakout Board Evaluation Kit Ordering Part Number POWR1014A-B-EVN Technical Support Assistance Hotline: 1-800-LATTICE (North America) +1-503-268-8001 (Outside North America) e-mail: [email protected] Internet: www.latticesemi.com 9 China RoHS Environment-Friendly Use Period (EFUP) POWR1014A Breakout Board Evaluation Kit User’s Guide Revision History Date Version March 2011 01.0 Initial release. Change Summary February 2012 01.1 Updated document with new corporate logo. © 2012 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 10 11 A B C D 5 5 4 4 PROTOTYPE AREA LED ARRAY 2 3 2 Resistant Tolerance: R12 1% All the rest up to 5% CONNECTED HEADER isp POWR CONNECTED HEADER 3 Date: Size B Title AXELSYS Sunday, December 19, 2010 POWR1014A-B-EVN Document Number 1 Sheet 1 POWR1014A Breakout Board, Cover 1 of 4 Rev A A B C D POWR1014A Breakout Board Evaluation Kit User’s Guide Appendix A. Schematics Figure 2. POWR1014A Breakout Board USB to JTAG USB CON A B C 5 1 2 J2 2 VCC DD+ ID GND 1k SKT_MINIUSB_B_RA D9 Green R1 1 1 C10 10u 1 2 3 4 5 VBUS_5V 2 IN 2 FT_EEDATA 1 0 1 0.1uF R19 2 C20 600ohm 500mA L4 3 OUT TAB R22 1 R21 10k 1 10 0 C15 0.1uF 2k2 2 2 R17 2 R18 1 NCP1117ST33 GND 2 4 FT_EECS FT_EECLK R2 2 Default 1 0 1 C11 22u 4 Dm Dp 2 1 2 3 4 VCC NU ORG VSS 93LC56-SO8 CS CLK DI DO U3 C13 0.1uF 8 7 6 5 1 C21 0.1uF C12 4u7 VCC3FT VCC3FT L3 2 1 600ohm 500mA L2 2 1 600ohm 500mA C1 4u7 C14 0.1uF C2 0.1uF VCC3D 1 C3 4u7 C18 18pF C16 10u VCC1_8FT 2 1 2 1 12MHZ 3 3 4 3 VCC3FT G1 G2 1 X1 C4 0.1uF C17 0.1uF 2 VCC3A C19 18pF 63 62 61 FT_EECS FT_EECLK FT_EEDATA 13 3 2 6 12k 1% 2 R12 1 14 2 R11 5k1 1 7 8 49 50 VCC1_8FT FT2232H VCC3FT PWREN# BCBUS0 BCBUS1 BCBUS2 BCBUS3 BCBUS4 BCBUS5 BCBUS6 BCBUS7 BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3 ACBUS4 ACBUS5 ACBUS6 ACBUS7 ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 SUSPEND# FTDI High-Speed USB TEST OSCO OSCI EECS EECLK EEDATA REF RESET# DM DP VREGOUT VREGIN U2 FT2232HL VCC3FT 2 36 60 48 52 53 54 55 57 58 59 38 39 40 41 43 44 45 46 26 27 28 29 30 32 33 34 16 17 18 19 21 22 23 24 VCC3FT 1 2 L1 2 1 600ohm 500mA 2 1 10 10 10 0 C5 0.1uF cc0402 1 2 R3 2 R4 2 R7 2 R9 2 3 C6 0.1uF cc0402 1 2 U1 1 2 1 2 1 2 3 4 5 6 7 8 TCK TDO TDI TMS DNI Date: Size C Title header_1x8 1 2 3 4 5 6 7 8 J1 C7 0.1uF cc0402 1 2 2 1 2 1 2 1 2 VCC_3.3V 1 2 1 2 1 2 R15 5k1 R20 5k1 R16 5k1 VCC3FT C9 0.1uF cc0402 1 TCK ( 4 ) TDI ( 4 ) TDO ( 4 ) TMS ( 4 ) TDISEL ( 4 ) ATDI ( 4 ) 1 Tuesday, December 21, 2010 POWR1014A-B-EVN Document Number Sheet 2 of POWR1014A Breakout Board, USBIF to JTAG AXELSYS R14 5k1 TCK TDI TDO TMS VCC3FT C8 0.1uF cc0402 1 2 VBUS_5V 1 2 2 1 4 9 VPHY VPLL 4 1 2 2 1 12 37 64 VCORE VCORE VCORE AGND 1 2 20 31 42 56 10 1 2 VCCIO VCCIO VCCIO VCCIO GND GND GND GND GND GND GND GND 1 5 11 15 25 35 47 51 1 2 1 12 2 D 5 4 Rev A A B C D POWR1014A Breakout Board Evaluation Kit User’s Guide Figure 3. USB Interface to JTAG A B C 5 J4 Proto Type Area Proto Type Area ( 4 ) OUT[14:4] 4X15 PROTOTYPE AREA 1 VCC3D 1 2 1 OUT14 2 D8 Red R39 2k 1 2 R51 2k 1 2 1 OUT13 2 4 R52 2k D6 Red R41 2k R53 2k VCC3D D5 Red R42 2k OUT6 OUT5 OUT4 R54 2k D4 Red R43 2k R59 2k 1 2 1 2 SMBA_OUT LED DISPLAY ARRAY D7 Red R40 2k 4 1 2 1 2 1 OUT12 2 1 2 1 2 1 OUT11 2 1 2 1 2 R55 2k R60 2k 1 R61 2k D3 Red R44 2k 2 R56 2k R62 2k 3 D2 Red R45 2k R57 2k ( 4 ) SCL_ ( 4 ) SDA_ 3 2 1 2 1 2 1 2 OUT9 1 OUT10 2 1 2 1 2 2 OUT8 1 1 2 OUT7 1 1 2 1 2 2 1 D1 Red R58 2k ( 4 ) HVOUT2 ( 4 ) HVOUT1 (4) (4) (4) (4) ispIN1 ispIN2 ispIN3 ispIN4 C27 0.1uF ( 4 ) SMBA_OUT ( 4 ) VMON[10:1] R46 2k 2k2 R26 ( 4 ) PLDCLK ( 4 ) MCLK ( 4 ) RESETB 2k2 R25 VCC3D 2 1 ( 4 ) OUT[14:4] 1 2 1 2 1 2 13 C28 0.1uF 1 2 D 5 VMON10 VMON9 VMON8 VMON7 VMON6 VMON5 VMON4 VMON3 VMON2 VMON1 C29 0.1uF VCC_3.3V OUT14 OUT13 OUT12 OUT11 OUT10 OUT9 OUT8 OUT7 OUT6 OUT5 OUT4 J3 1 2 3 4 5 6 7 8 9 10 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132 3334 3536 3738 3940 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 2 J6 1 2 3 4 5 6 7 8 9 10 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132 3334 3536 3738 3940 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 header_2x20 DNI 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 EXTERNAL POWER PINS header_2x20 DNI 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 Title Date: Size C AXELSYS 1 Tuesday, December 21, 2010 POWR1014A-B-EVN Document Number Sheet 3 of POWR1014A Breakout Board, CON and LED 1 4 Re v A A B C D POWR1014A Breakout Board Evaluation Kit User’s Guide Figure 4. Connectors and LEDs A B 5 ( 3 ) ispIN1 ( 3 ) ispIN2 ( 3 ) ispIN3 ( 3 ) ispIN4 4 R47 5k1 R48 5k1 R49 5k1 R50 5k1 ( 3 ) VMON[10:1] 1 C 4 1 2 1 2 1 2 14 2 TDISEL ATDI TDI TMS TCK TDO ( 3 ) SCL_ ( 3 ) SDA_ (2) (2) (2) (2) (2) (2) VMON1 VMON2 VMON3 VMON4 VMON5 VMON6 VMON7 VMON8 VMON9 VMON10 3 3 39 38 19 17 18 16 22 21 44 46 47 48 25 26 27 28 32 33 34 35 36 37 ispPAC-POWR1014A-02TN48I SCL SDA TDISEL ATDI TDI TMS TCK TDO IN1 IN2 IN3 IN4 VMON1 VMON2 VMON3 VMON4 VMON5 VMON6 VMON7 VMON8 VMON9 VMON10 U4 VCC3A VCC3D HVOUT1 HVOUT2 C22 0.1uF cc0402 GNDA GNDD2 GNDD1 PLDCLK MCLK RESETB SMBA_OUT3 OUT4 OUT5 OUT6 OUT7 OUT8 OUT9 OUT10 OUT11 OUT12 OUT13 OUT14 TP1 2 1 VCC3A 1 23 41 29 45 24 20 VCCD1 VCCD2 VCCA VCCINP VCCPROG VCCJ 15 14 30 31 7 42 43 40 13 12 11 10 9 8 6 5 4 3 2 1 VCC3D 1 C23 0.1uF cc0402 OUT4 OUT5 OUT6 OUT7 OUT8 OUT9 OUT10 OUT11 OUT12 OUT13 OUT14 2 1 2 C24 0.1uF cc0402 HVOUT1 ( 3 ) HVOUT2 ( 3 ) C25 0.1uF cc0402 2 C26 0.1uF cc0402 PLDCLK ( 3 ) MCLK ( 3 ) RESETB ( 3 ) OUT[14:4] ( 3 ) SMBA_OUT ( 3 ) 2 1 2 1 2 D 5 Title Date: Size C AXELSYS 1 Sunday, December 19, 2010 POWR1014A-B-EVN Document Number Sheet 4 of 4 POWR1014A Breakout Board, Lattice ispPOWR 1 Re v A A B C D POWR1014A Breakout Board Evaluation Kit User’s Guide Figure 5. POWR1014A POWR1014A Breakout Board Evaluation Kit User’s Guide Appendix B. Bill of Materials Table 6. POWR1014A Breakout Board Evaluation Kit Bill of Materials Item Quantity Reference 1 3 C1, C3, C12 2 21 C2, C4, C5, C6, C7, C8, C9, C13 Part Class Description Manufacturer Manufacturer Part Number Digikey P/N PCB Footprint 4u7 Cap Cer 4.7uF Discrete 6.3V 10% X5R 0603 Panasonic ECJ-1VB0J475K 0.1uF Cer 0.1uF Discrete Cap 16V X7R 0402 Kemet C0402C104K4RA 399-3521-2-ND CTU cc0402 PCC2396CT-ND Assembly cc0603 C14, C15, C17, C20, C21, C22 C23, C24, C25, C26, C27, C28 C29 3 2 C10, C16 10u Cap Cer 10uF Discrete 6.3V 20% X5R 0603 Panasonic ECJ-1VB0J106M cc0603 4 1 C11 22u CER 22UF Discrete CAP 10V X5R 0805 Taiyo Yuden LMK212BJ226M G-T cc0805 5 2 C18, C19 18pF CER 18PF Discrete CAP 25V C0G 0402 Kemet C0402C180K3GA C0402C180K3GA CTU CTU-ND cc0402 6 8 D1, D2, D3, D4, D5, D6, D7, D8 Red LED SUPER RED Discrete CLEAR 0603 Lite-On Inc SMD LTST-C190KRKT 7 1 D9 Green LED SUPER Discrete GREEN CLEAR 0603 SMD LTST-C190KGKT 8 1 J1 header_1x8 9 1 J2 SKT_MINIUSB_B_RA 10 2 J3, J6 11 1 J4 Lite-On Inc 160-1436-2-ND led_0603 led_0603 hdr_amp_87220_ 8_1x8_100 IO Neltron 5075BMR-05-SMCR skt_miniusb_b_ra header_2x20 Proto Type Area hdr_samtec_mtsw _2x20_100 DNI hdr_th_4x15_100 DNI 600ohm 500mA Ferrite Bead Discrete 600ohm@100MH Murata z 500mA 0603 BLM18AG601SN 1D 490-1014-1-ND FB0603 12 4 L1, L2, L3, L4 13 1 R1 1k 1/16W 1K 1% Yageo Discrete Res 0402 RC0402FR071KL 311-1.00KLRTRND cr0402 14 8 R2, R3, R4, R7, R9, R17, R18 0 1/10W 0.0 Discrete Res Ohm 5% 0603 Yageo RC0603JR070RL 311-0.0GRTR-ND cr0603 5k1 1/16W 5.1K Discrete Res 1% 0402 Yageo RC0402FR075K1L 311-5.10KLRTRND cr0402 12k 1/16W 12.0K Yageo Discrete Res 1% 0402 RC0402FR0712KL 311-12.0KLRTRND cr0402 10k 1/16W 10.0K Yageo Discrete Res 1% 0402 RC0402FR0710KL 311-10.0KLRTRND cr0402 Yageo RC0402FR072K2L 311-2.20KLRTRND cr0402 Yageo RC0402JR072KL 311-2.0KJRTRND cr0402 R19 15 9 R11, R14, R15, R16, R20, R47 R48, R49, R50 16 17 1 1 R12 R21 18 3 R22, R25, R26 2k2 1/16W 2.2K Discrete Res 1% 0402 19 20 R39, R40, R41, R42, R43, R44 2k RES 2.0K OHM Discrete 1/16W 5% 0402 SMD R45, R46, R51, R52, R53, R54, R55, R56, R57, R58, R59, R60 R61, R62 20 1 TP1 TP_S_40_63 21 1 U1 NCP1117ST33 22 1 U2 FT2232HL 23 1 U3 93LC56-SO8 24 1 U4 ispPAC-POWR1014A -02TN48I 25 1 X1 12MHZ IO Square test point, 40mil inner diameter, 63mil outer diameter tp_s_40_63 On Semi IC IC 93LC56 EEPROM sot223_4p FTDI FT2232HL Microchip 93LC56T-I/SN tqfp64_0p5_12p2 x12p2_h1p6 so8_50_244 tqfp48_0p5_9p2x 9p2_h1p7 TXC 15 7M-12.000MAAJT DNI crystal_4p_3p2x2 p5