Product data sheet

Product datasheet
OT 150/220…240/700 3DIMLT+ E
OPTOTRONIC | Constant current LED power supplies with 3DIM/DALI
Areas of application
_ Suitable for luminaires of protection classes I and II
_ Suitable for outdoor applications in luminaires with IP >
54
__
Product benefits
_ Large output power range: up to 150 W
_ High surge protection: up to 4/6 kV (L-N), 4/6 kV (L/N-PE)
_ Different dimming modes and levels can be set
_ Stand-alone dimming function enables operation in existing installations
Product features
_ 3DIM functionality (StepDIM/AstroDIM/DALI)
_ Current output range: 75…700 mA
_ Flexible current setting
_ Constant lumen function
_ Overtemperature protection via external NTC (3DIMLT+ version only)
June 17, 2016, 11:44:15
OT 150/220…240/700 3DIMLT+ E
© 2016, OSRAM GmbH. All rights reserved.
Page 1 of 6
Product datasheet
Technical data
Electrical data
__
Nominal voltage
220…240 V
Input voltage AC
195…264 V 1)
Nominal current
0.72 A 2)
Mains frequency
50…60 Hz
Nominal input voltage (SD port)
220…240 V 3)
Power factor λ
0.95/0.90
Total harmonic distortion
10 %
Device power loss
15.0 W 5)
Inrush current
58 A 6)
Max. ECG no. on circuit breaker 10 A (B)
4
7)
Max. ECG no. on circuit breaker 16 A (B)
8
7)
Max. ECG no. on circuit breaker 25 A (B)
14
Max. no. of ECGs on 16A MCB with EBN-OS
20
Surge capability (L/N-Ground)
6 kV 8)
Surge capability (L-N)
6 kV 9)
Surge capability (L/N – SD)
4 kV 9)
Surge capability (SD – Ground)
4 kV 8)
Nominal output power
150 W 10)
ECG efficiency
90.5 % 11)
Nominal output voltage
95…335 V
U-OUT (working voltage)
350 V
Nominal output current
350…700 mA
Output current tolerance
±5 %
Output ripple current (100 Hz)
15 %
Minimum output current
75 mA
Galvanic isolation
double/reinforced
4)
7)
1) Permitted voltage range
2) At 230 V
3) In relation to L/N / Active: input current > 650 µA
4) Minimum/Full load at 230 V/Half load at 230 V
pk
/ Inactive: input currrent < 12 µA
pk
5) Maximum
6) t
width
7) Type B
= 360 µs (measured at 50 % I
)
peak
8) EQUI @ 12 Ohm acc. to EN 61547
9) @ 2 Ohm, acc. to EN61547
10) Partial load 34…150 W / Not dimmed
11) At full load and 230 V
June 17, 2016, 11:44:15
OT 150/220…240/700 3DIMLT+ E
© 2016, OSRAM GmbH. All rights reserved.
Page 2 of 6
Product datasheet
Dimensions & weight
__
Mounting hole spacing, length
160.0 mm
Mounting hole spacing, width
90.0 mm
Length
170.0 mm
Width
100.0 mm
Height
40.0 mm
Product weight
1100.00 g
Cable cross-section, input side
0.25…2.5 mm² 1)
Cable cross-section, output side
0.25…1.5 mm² 2)
Wire preparation length, input side
10…11 mm 3)
1) Flexible / Solid leads / Equipotential pole only 0.25…1.5 mm²
2) LEDset only 0.2…0.5 mm² / Solid leads / Flexible
3) Equipotential pole 8.5…9.5
Temperatures & operating conditions
Ambient temperature range
-30…+55 °C
Maximum temperature at tc test point
85 °C 1)
Max.housing temperature in case of fault
120 °C
Permitted rel. humidity during operation
5…85 %
1) Maximum at the Tc-point
Lifespan
ECG lifetime
1) At T
case
85000 h 1)
= 75°C at T point / 10% failure rate
c
June 17, 2016, 11:44:15
OT 150/220…240/700 3DIMLT+ E
© 2016, OSRAM GmbH. All rights reserved.
Page 3 of 6
Product datasheet
Expected Lifetime
Product name
OT
150/220…240/700
3DIMLT+ E
ECG ambient temperature [ta]
55
45
40
Temperature at tc-point [°C]
85
75
70
1)
1)
100000 1)
Lifetime [h]
50000
85000
1) Max. 10% failure rate at tc max and input voltage 230 V
AC
Capabilities
__
Dimmable
No
Dimming interface
3DIM / DALI / StepDIM / AstroDIM
Dimming range
10…100 % 1)
Suitable for fixtures with prot. class
I / II
Constant lumen function
Programmable
NTC input
Yes
Overheating protection
Automatic reversible
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Max. cable length to lamp/LED module
2.0 m
2)
1) For 700mA nominal output current
2) Supports 10K, 5 %, NCP18XH103J03RB / Supports 15K, 5 %, NCP18XW153J03RB / Supports 15K, 3 %, NCP15XW153E03RC + 390 Ohm / EPCOS
B57423V2473H
Certificates & standards
1)
Type of protection
IP20
Standards
Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to
IEC 62384/Acc. to EN 55015:2006 + A1:2007 +
A2:2009/Acc. to IEC 61000-3-2/Acc. to IEC 61000-33/Acc. to EN 61547/Acc. to IEC 62386-101/Acc. to IEC
62386-102/Acc. to IEC 62386-207
Approval marks – approval
CE / ENEC 10 / VDE
1) IP Fixture rating > IP54
Logistical data
Temperature range at storage
June 17, 2016, 11:44:15
OT 150/220…240/700 3DIMLT+ E
-20…80 °C
© 2016, OSRAM GmbH. All rights reserved.
Page 4 of 6
Product datasheet
Wiring Diagram
Wiring diagram
__
Wiring diagram
Equipment / Accessories
_ DALI magic hardware for configuring 3DIM ECGs necessary
Additional product information
_ Shut down of output load happens if the input voltage of the load is below the allowed minimum output voltage of the driver.
The driver automatically tries to switch on the load cyclically.
_ In case the input voltage of the load exceeds the output voltage range of the driver, it automatically reduces the output
current to keep the output voltage controlled to the maximum allowed output voltage.
_ The driver automatically reduces the output current in case the maximum allowed output power is exceeded.
_ The EQUI pin shall be connected to the heat sink of the LED module to improve the surge withstand capability of the system
and EMI in critical luminaires.
_ Several external NTCs are supported for temperature protection of the LED module or luminaire. The type of NTC can be
selected in the programming software in the temperature based mode. By default the resistor based mode is actived with
following values: start derating: 6.3 kOhm, end derating 5.0 kOhm, shut off: 4.3 kOhm, derating level 50 %.
_ The default dimming mode is StepDIM / AstroDIM / DALI (wiring selection) with following values for:- StepDIM: 100 % on, 50
% dimming level if SD port is active, fade time 180 s- AstroDIM: 100 % on, 50 % dimming level, 6 h dimming duration, start of
dimming duration 2 h before the middle of the average switched-on time, fade time 180 s
_ The constant lumen feature is disabled by default.
_ If any output level is below the physical min level, the physical min level will be used.
_ An external relay connected in front of the SD port is necessary in installations with leakage currents from N and L exceeding
the defined limits per device (SD input current: active > 650 µAp and inactive < 12 µAp). The relay needs to be selected in a
way that it is not switched or hold by the occurring leakage currents in the installation. This relay is also needed to ensure the
compatibility with the new 4DIMLT2 OPTOTRONIC drivers.
June 17, 2016, 11:44:15
OT 150/220…240/700 3DIMLT+ E
© 2016, OSRAM GmbH. All rights reserved.
Page 5 of 6
Product datasheet
Download Data
File
Brochures
APPLICATION GUIDE. The LEDset interface. (GB)
Brochures
LMS 3 DIM Flyer (GB)
Brochures
3DIM - controll gears - Reliable, durable and efficient (G)
Brochures
3DIM Application Guide (GB)
Brochures
Overvoltage protection for LED street lighting (EN)
Declarations of conformity
CE Conformity OT 150220-240700 3DIMLT+ E
CAD data 3-dim
CAD OT 150-3DIM LT
Product movie
3DIM Astro, StepDIM, DALI Video
Logistical Data
__
Product code
Product description
Packaging unit (Pieces/Unit)
Dimensions (length x width x
height)
Volume
Gross weight
4008321978202
OT 150/220…240/700
3DIMLT+ E
Shipping carton box
10
303 mm x 285 mm x 205 mm
17.70 dm³
11587.00 g
The mentioned product code describes the smallest quantity unit which can be ordered. One shipping unit can contain one or
more single products. When placing an order, for the quantity please enter single or multiples of a shipping unit.
Disclaimer
Subject to change without notice. Errors and omission excepted. Always make sure to use the most recent release.
June 17, 2016, 11:44:15
OT 150/220…240/700 3DIMLT+ E
© 2016, OSRAM GmbH. All rights reserved.
Page 6 of 6