Product datasheet OT 90/170…240/1A0 4DIMLT2 E OPTOTRONIC | Constant current LED power supplies with 4DIM/DALI Areas of application _ Street and urban lighting _ Industry _ Suitable for outdoor applications in luminaires with IP > 54 _ Suitable for use in outdoor luminaires of protection class I and II __ Product benefits _ 4DIM functionality in one device (StepDIM, AstroDIM, MainsDIM, DALI) _ Very high efficiency and reliability _ High surge protection: up to 10 kV (1 pulse) / 8 kV, in protection class I or II _ Low luminous efficacy tolerance through low output current tolerance of ± 3 % _ Great flexibility due to wide operating temperature range of -40…55 °C or 60 °C _ Protection through double isolation between mains input and LED output Product features _ Available with different wattage: 40 W, 60 W, 90 W, 165 W _ Input voltage: 120…277 V (40 W), 220…240 V (60 W, 90 W, 165 W) _ Current output range: 70…1,050 mA _ Flexible current setting with one additional wire (LEDset2) _ AstroDIM for autonomous dimming with five independent levels (astro, time mode) _ Allows for energy saving in twilight phases _ MainsDIM function for dimming via reduction of line voltage amplitude _ Isolated DALI interface for bidirectional telemanagement systems _ Standby power consumption: < 0.5 W _ Constant lumen function _ Overtemperature protection via external NTC June 17, 2016, 11:43:50 OT 90/170…240/1A0 4DIMLT2 E © 2016, OSRAM GmbH. All rights reserved. Page 1 of 6 Product datasheet Technical data Electrical data __ Nominal voltage 220…240 V Input voltage AC 170…264 V 1) Nominal current 0.46 A 2) Mains frequency 50…60 Hz Nominal input voltage (SD port) 220…240 V 3) Power factor λ 0.95/0.90 Total harmonic distortion 10 % Device power loss 9.6 W 5) Inrush current 57 A 6) Max. ECG no. on circuit breaker 10 A (B) 7 Max. ECG no. on circuit breaker 16 A (B) 12 7) Max. ECG no. on circuit breaker 25 A (B) 20 7) Max. no. of ECGs on 16A MCB with EBN-OS 30 Surge capability (L/N-Ground) 8 kV 8) Surge capability (L-N) 6 kV 9) Surge capability (L/N – SD) 6 kV 9) Surge capability (SD – Ground) 8 kV 8) Nominal output power 90 W 10) ECG efficiency 91.5 % 11) Nominal output voltage 57…186 V U-OUT (working voltage) 200 V Nominal output current 350…1050 mA Output current tolerance ±3 % Output ripple current (100 Hz) 15 % Minimum output current 70 mA 12) Galvanic isolation double/reinforced 4) 7) 1) Permitted voltage range 2) At 230 V 3) In relation to N / Active: input current > 2.0 mA pk 4) Minimum/Full load at 230 V/Half load at 230 V / Inactive: input currrent < 0.5 mA pk / Suitable for three phase System only for 220…240 V AC 5) Maximum 6) t width 7) Type B = 210 µs (measured at 50 % I ) peak 8) EQUI @ 12 Ohm acc. to EN 61547 9) @ 2 Ohm, acc. to EN61547 10) Partial load 20…90 W / Not dimmed 11) At full load and 230 V 12) Physical Minimum Dimming Current 70 mA June 17, 2016, 11:43:50 OT 90/170…240/1A0 4DIMLT2 E © 2016, OSRAM GmbH. All rights reserved. Page 2 of 6 Product datasheet Dimensions & weight __ Length 133.0 mm Width 77.0 mm Height 40.0 mm Mounting hole spacing, length 122.5 mm Mounting hole spacing, width - Product weight 340.00 g Cable cross-section, input side 0.25…2.5 mm² 1) Cable cross-section, output side 0.25…1.5 mm² 2) Wire preparation length, input side 10…11 mm 3) 1) Flexible / Solid leads / Equipotential pole only 0.2…1.5 mm² 2) Flexible / Solid leads 3) Equipotential pole 8.5…9.5 Temperatures & operating conditions Ambient temperature range -40…+55 °C Maximum temperature at tc test point 90 °C 1) Max.housing temperature in case of fault 120 °C Permitted rel. humidity during operation 5…85 % 1) Maximum at the Tc-point Lifespan ECG lifetime 1) At T case 85000 h 1) = 80°C at T point / 10% failure rate c June 17, 2016, 11:43:50 OT 90/170…240/1A0 4DIMLT2 E © 2016, OSRAM GmbH. All rights reserved. Page 3 of 6 Product datasheet Expected Lifetime Product name OT 90/170…240/1A0 4DIMLT2 E ECG ambient temperature [ta] 55 45 42 Temperature at tc-point [°C] 90 80 77 1) 1) 100000 1) Lifetime [h] 50000 85000 1) Max. 10% failure rate at tc max and input voltage 230 V AC Capabilities __ Dimmable Yes Dimming interface 4DIM / DALI / StepDIM / AstroDIM / MainsDIM Dimming range 10…100 % 1) Suitable for fixtures with prot. class I / II Constant lumen function Programmable NTC input Yes Overheating protection Automatic reversible Overload protection Automatic reversible Short-circuit protection Automatic reversible No-load proof Yes Max. cable length to lamp/LED module 2.0 m 2) 1) For ≥700mA nominal output current 2) Supports 15K, 5 %, NCP18XW153J03RB / Supports 15K, 3 %, NCP15XW153E03RC + 390 Ohm / Supports 10K, 5 %, NCP18XH103J03RB / EPCOS B57423V2473H Certificates & standards 1) Type of protection IP20 Standards Acc. to EN 61347-1/Acc. to EN 61347-2-13/Acc. to EN 62384/Acc. to EN 55015:2006 + A1:2007 + A2:2009/Acc. to EN 61547/Acc. to IEC 61000-3-2/Acc. to IEC 61000-3-3/Acc. to IEC 62386-101/Acc. to IEC 62386-102/Acc. to IEC 62386-207 Approval marks – approval CE / ENEC 10 / VDE / VDE-EMC / CQC (in preparation) 1) IP Fixture rating > IP54 Logistical data Temperature range at storage June 17, 2016, 11:43:50 OT 90/170…240/1A0 4DIMLT2 E -25…80 °C © 2016, OSRAM GmbH. All rights reserved. Page 4 of 6 Product datasheet Wiring Diagram Wiring diagram __ Wiring diagram Equipment / Accessories _ DALI magic hardware for configuring 4DIM ECGs necessary _ Programmable via Tuner4TRONIC software Additional product information _ Default output current is 700 mA without any resistor connected to the LEDset port. As soon as the driver detects one time a resistor value within the resistor range of 2.37 kOhm (1050 mA) and 24.9 kOhm (200 mA) for more than 3 s, the driver activates the LEDset2 mode. _ The driver withstands an input voltage of up to 350 Vac for a maximum of two hours. Shut down of output load might occur in case the supply voltage exceeds the declared input voltage range. _ Shut down of output load happens if the input voltage of the load is below the allowed minimum output voltage of the driver. The driver automatically tries to switch on the load cyclically. _ In case the input voltage of the load exceeds the output voltage range of the driver, it automatically reduces the output current to keep the output voltage controlled to the maximum allowed output voltage. _ The driver automatically reduces the output current in case the maximum allowed output power is exceeded. _ The driver automatically adjusts the output voltage to the maximum output voltage if no load is connected and switches off the load after some seconds. Hot-plug of the load or external switching on the secondary side is not allowed. _ The driver is protected against temporary overheating by automatic reduction of the output current down to 30 % and then switches off. _ The EQUI pin shall be connected to the heat sink of the LED module to improve the surge withstand capability of the system and EMI in critical luminaires. _ Several external NTCs are supported for temperature protection of the LED module or luminaire. The type of NTC can be selected in the programming software in the temperature based mode. By default the resistor based mode is actived with following values: start derating: 6.3 kOhm, end derating 5.0 kOhm, shut off: 4.3 kOhm, derating level 50 %. June 17, 2016, 11:43:50 OT 90/170…240/1A0 4DIMLT2 E © 2016, OSRAM GmbH. All rights reserved. Page 5 of 6 Product datasheet _ The default dimming mode is StepDIM / AstroDIM / DALI (wiring selection) with following values for:- StepDIM: 100 % on, 50 % dimming level if SD port is active, fade time 180 s- AstroDIM: 100 % on, 50 % dimming level, 6 h dimming duration, start of dimming duration 2 h before the middle of the average switched-on time, fade time 180 s _ The constant lumen feature is disabled by default. _ For MainsDIM dimming mode and for 170 Vac input voltage condition the output power should not exceed 85 % of the maximum declared output power. _ For input voltage of 170…190 Vac, the maximum allowed output power is linear limited starting from 100 % at 190 Vac down to 85 % at 170 Vac, except for the 40 W type. _ If any output level is below the physical min level, the physical min level will be used. _ In case the 3DIM and 4DIMLT2 devices are operated on one common control phase connected to SD input the 3DIM devices needs to have a relay as described in the 3DIM application guide. _ The SD port is suitable for three phase systems with 220…240 Vac, for other input voltages only single phase systems are supported. _ For further details please consult the 4DIMLT2 application guide. Download Data File Brochures Technical Application Guide 4DIMLT2 LED drivers (GB) Brochures Overvoltage protection for LED street lighting (EN) Certificates CB certificate 40W 60W 90W 4DIM __ Declarations of conformity Synergrid Conformity 4DIMLT2 Declarations of conformity EMC Certificate Declarations of conformity ENEC certificate Declarations of conformity Declaration of Conformity OT 4 DIM LT2 E Logistical Data Product code Product description Packaging unit (Pieces/Unit) Dimensions (length x width x height) Volume Gross weight 4052899925205 OT 90/170…240/1A0 4DIMLT2 E Shipping carton box 20 495 mm x 330 mm x 140 mm 22.87 dm³ 7523.00 g The mentioned product code describes the smallest quantity unit which can be ordered. One shipping unit can contain one or more single products. When placing an order, for the quantity please enter single or multiples of a shipping unit. Disclaimer Subject to change without notice. Errors and omission excepted. Always make sure to use the most recent release. June 17, 2016, 11:43:50 OT 90/170…240/1A0 4DIMLT2 E © 2016, OSRAM GmbH. All rights reserved. Page 6 of 6