GBU8A THRU GBU8M

GLASS PSSIVATED SINGLE-PHASE BRIDGE RECTIFIER
CURRENT
FEATURES
21.8 - 22.3
3.2×45
3.5 - 4.1
2.16 - 2.54
1.02 - 1.27
MECHANICAL DATA
•
•
•
1.9 - 2.16
17.5 - 18.0
2.0 - 2.2
•
•
3.3 - 3.56
O
18.3 - 18.8
R0.5
1.52 - 2.03
•
•
•
•
•
8.0 Amperes
GBU
Plastic package has Underwriters Laboratory
Flammability Glassification 94V-0
High case dielectric strength of 1500 VRMS
Ideal for printed circuit boards
Glass passivated chip junctions
High surge current capability
High temperature soldering guaranteed
260℃/10 seconds, 0.375”(9.5mm) lead length
at 5 lbs. (2.3kg) tension
7.4 - 7.9
•
50 to 1000 Volts
VOLTAGE RANGE
GBU8A THRU GBU8M
0.46 - 0.68
4.83 - 5.35
Case: molded plastic body over passivated junctions
Terminal: Plated leads solderable per MIL-STD-750
Method 2026
Mounting position: Any (Note 2)
Mounting Torque: 5 in-1b.Max.
Weight: 0.15 ounce,4.0 gram
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
•
Ratings at 25℃ ambient temperature unless otherwise specified
Single Phase, half wave, 60Hz, resistive or inductive load
For capacitive load derate current by 20%
GBU GBU
SYMBOLS
8B
8A
Maximum Reverse Peak Repetitive Voltage
VRRM
50
100
Maximum RMS Voltage
VRMS
35
70
Maximum DC Blocking Voltage
VDC
50
100
Maximum Average Forward T C=100℃(Note 1,2)
I
•
•
Rectified Output Current, At
Peak Forward Surge Current
8.3ms single half sine wave superimposed on
rated load (JEDEC Method)
Rating for Fusing (t<8.3ms)
Maximum Instantaneous Forward Voltage drop
Per leg at 4.0A
TA=25℃
Maximum Reverse Current at rated
DC blocking voltage per element
TA=125℃
Typical Junction Capacitance (Note 4)
Typical Thermal Resistance (Note 2)
Typical Thermal Resistance (Note 1)
Operating and Storage Temperature Range
GBU
8D
200
140
200
GBU
8G
400
280
400
GBU
8J
600
420
600
GBU
8K
800
560
800
GBU
8M
1000
700
100
UNIT
Volts
Volts
Volts
(AV)
8.0
Amps
IFSM
175
Amps
I2 t
127
A2s
VF
1.0
Volts
IR
5.0
500
mAmps
CJ
RJA
RJL
TJ ,TSTG
211
Amps
94
21
2.2
(-55 to +150)
Notes: 1. Unit mounted on 2.6×1.6×0.06” thick (6.5×3.5×0.15cm) AL. plate heatsink
2. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum
Heat transfer with #6 screw
3. Units ,mounted in free air, no heatsink on P.C.B (12×12mm) copper pads, 0.375” lead length
3. Measured at 1.0 MHz and applied reverse voltage of 4.0 V
Web Site: www.hkmic.com
pF
℃/W
℃/W
℃
GLASS PSSIVATED SINGLE-PHASE BRIDGE RECTIFIER
50 to 1000Volts
VOLTAGE RANGE
GBU8A THRU GBU8M
CURRENT
8.0 Ampere
RATINGS AND CHARACTERISTIC CURVES GBU8A THRU GBU8M
FIG. 2- MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
250
10
60 Hz Resistive or Inductive Load
PEAK FORWARD SURGE,
CURRENT,(A)
AVERAGE FORWARD OUTPUT CURRENT
(A)
FIG. 1- DERATING CURVE
OUTPUT RECTIFIED CURRENT
8.0
Heat-Sink Mounting,on
3.2×3.2×0.12"Thk
(8.2×8.2×0.3cm)AL.Plate
6.0
4.0
2.0
TJ =150℃
8.3ms Single Half Sine-Wave
(JEDEC Method)
200
150
100
50
0
0
0
20
50
80
120
100
150
1
CASE TEMPERATURE, ℃
FIG. 4- TYPICAL REVERSE CHARACTERISTICS
PER LEG
FIG. 3- TYPICAL FORWORD
CHARACTERISTICS PER LGE
500
INSTANTANEOUS REVERSE
CURRENT, (A)
INSTANTANEOUS FORWARD
CURRENT, (A)
100
10
1
0.1
TJ=25℃
Pulse width=300μS
1% Duty Cycle
0.01
0.4
0.6
0.8
1.0
1.2
1.4
1
0.1
TRANSIENT THERMAL IMPEDANCE
(℃/W)
JUNCTION CAPACITANCE, (pF)
0
20
40
60
80
100
100
100
50-400V
600-1000V
10
10
T J =25℃
FIG. 6- TYPICAL TRANSIENT THERMAL
IMPEDANCE PER LEG
T j =25℃
f=1.0 MHz
Vsig=50mVp-p
1
50-400V
600-1000V
PERCENT OF RATED PEAK REVERSE VOLTAGE,(% )
FIG. 5- TYPICAL JUNCTION CAPACITANCE
PER LEG
0.1
T J =125℃
10
0.01
1.6
T J =150℃
100
INSTANTANEOUS FORWARD VOLTAGE,(V)
1000
100
10
NUMBER OF CYCLES AT 60 Hz
100
REVRESE VOLTAGE,(V)
Web Site: www.hkmic.com
10
1
0.1
0.01
0.1
1
10
T, HEATING TIME (SEC.)
100