SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER CURRENT • • • 4.4-4.8 3.4-3.8 .1 φ3 -3 . 4 1.5-1.9 0.8-1.0 Case: molded plastic body Terminal: Plated leads solderable per MIL-STD-750 Method 2026 Mounting position: Any (Note 2) Mounting Torque: 6 in – 1bs max. Weight: 0.15 ounce,4.0 gram 2.8-3.2 17.2-17.8 MECHANICAL DATA • • 24.8-25.2 O 9.3-9.7 3.0×45 3.6 14.7-15.3 Plastic package has UL Flammability Glassification 94V-0 Glass passivated chip junctions High case dielectric strength of 1500 VRMS High surge current capability High temperature soldering guaranteed 260℃/10 seconds, 0.375”(9.5mm) lead length 3.3-3.7 • • • • 8.0 Amperes KBJ FEATURES • 50 to 1000 Volts VOLTAGE RANGE KBJ8A THRU KBJ8M 0.6-0.8 0.9-1.1 7.3-7.7 7.2-7.7 7.3-7.7 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% KBJ SYMBOLS KBJ Maximum Reverse Peak Repetitive Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, At TC=100℃ Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC Method) Rating for Fusing (t<8.3ms) Maximum Instantaneous Forward Voltage drop Per bridge element 4.0A TA=25℃ Maximum DC Reverse Current at rated DC blocking voltage per element TA=125℃ Typical Junction Capacitance, per let (Measured at 1.0MHz and applied reverse voltage of 4.0V) Typical Thermal Resistance (Note 1) Operating Junction Temperature Range Storage Temperature Range VRRM VRMS VDC KBJ KBJ KBJ KBJ KBJ 8A 8B 8D 8D 8J 8K 8M 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 100 UNIT Volts Volts Volts I(AV) 8.0 Amps IFSM 170 Amps I2 t 120 A2s VF 1.0 Volts IR 5.0 500 μA CJ 211.0 RJA TJ TSTG 94.0 2.2 (-55 to +150) (-55 to +150) Notes: 1. Unit mounted on 2.6”×1.4”×0.06” thick (6.5×3.5×0.15cm) AL. plate. 2. Recommended mounting position is to bolt down on heatsink using #6 screw and silicon thermal Compound for maximum heat transfer Web Site: www.hkmic.com pF ℃/W ℃/W ℃ SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER 50 to 1000Volts VOLTAGE RANGE KBJ8A THRU KBJ8M CURRENT 8.0 Amperes RATINGS AND CHARACTERISTIC CURVES KBJ8A THRU KBJ8M FIG. 2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 250 10 60 Hz Resistive or Inductive Load PEAK FORWARD SURGE, CURRENT,(A) AVERAGE FORWARD OUTPUT CURRENT (A) FIG. 1- DERATING CURVE OUTPUT RECTIFIED CURRENT 8.0 Heat-Sink Mounting,on 3.2×3.2×0.12"Thk (8.2×8.2×0.3cm)AL.Plate 6.0 4.0 2.0 TJ =150℃ 8.3ms Single Half Sine-Wave (JEDEC Method) 200 150 100 50 0 0 0 20 50 80 120 100 150 1 FIG. 4- TYPICAL REVERSE CHARACTERISTICS PER LEG FIG. 3- TYPICAL FORWORD CHARACTERISTICS PER LGE 500 INSTANTANEOUS REVERSE CURRENT, (A) INSTANTANEOUS FORWARD CURRENT, (A) 100 10 1 0.1 TJ=25℃ Pulse width=300μS 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1 0.1 TRANSIENT THERMAL IMPEDANCE (℃/W) JUNCTION CAPACITANCE, (pF) 0 20 60 40 80 100 100 100 50-400V 600-1000V 10 10 1 0.1 100 10 TJ =25℃ FIG. 6- TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG TJ=25℃ f=1.0MHz Vsig=50mVp-p 1 50-400V 600-1000V PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG. 5- TYPICAL JUNCTION CAPACITANCE PER LEG 0.1 TJ =125℃ 10 0.01 1.6 TJ =150℃ 100 INSTANTANEOUS FORWARD VOLTAGE,(V) 1000 100 10 NUMBER OF CYCLES AT 60 Hz CASE TEMPERATURE, ℃ REVRESE VOLTAGE,(V) Web Site: www.hkmic.com 0.01 0.1 1 10 T, HEATING TIME (SEC.) 100