ispPAC-POWR607 Evaluation Board User’s Guide May 2007 Revision: EB28_01.0 ispPAC-POWR607 Evaluation Board User’s Guide Lattice Semiconductor Introduction Lattice Semiconductor’s Power Manager II ispPAC®-POWR607 device simplifies power supply design by integrating the analog and digital functions of power supply management (sequencing, monitoring, reset generation into a single device). This device provides designers with a rich set of features: precision comparators with a built-in voltage reference, MOSFET drivers and a programmable logic device (PLD) for sequencing and supervisory logic functions or reset control. Configuration for all subsystems in the ispPAC-POWR607 device is stored in non-volatile E2CMOS® memory. Programming is performed via the industry-standard JTAG IEEE 1149.1 interface. PAC-POWR607-EV Evaluation Board The PAC-POWR607-EV evaluation board (Figure 1) allows the designer to quickly configure and evaluate the ispPAC-POWR607 device on a fully assembled printed-circuit board. The board supports a 32-pin QFN package, pads for user I/O, a JTAG programming cable connector, LEDs and switches. JTAG programming signals can be generated by using an ispDOWNLOAD® programming cable connected between the evaluation board and a PC’s parallel (printer) port. Both analog and digital features of the ispPACPOWR607device can be easily configured using PAC-Designer® software. Figure 1. PAC-POWR607-EV Evaluation Board Programming Interface Lattice Semiconductor’s ispDOWNLOAD cable can be used to program the ispPAC-POWR607 device on the evaluation board. This cable plugs into a PC-compatible’s parallel port connector, and includes active buffer circuitry inside its DB-25 connector housing. The other end of the ispDOWNLOAD cable terminates in an 8-pin 0.100” pitch header connector, which plugs directly into a mating connector, (J3) provided on the PAC-POWR607-EV evaluation board. Important Note: The board must be un-powered when connecting, disconnecting, or reconnecting the ispDOWNLOAD Cable. Always connect the ispDOWNLOAD Cable's GND pin (black wire), before connecting any other JTAG pins. Failure to follow these procedures can in result in damage to the ispPAC-POWR607 device and render the board inoperable. 2 ispPAC-POWR607 Evaluation Board User’s Guide Lattice Semiconductor Power Supply Considerations The ispPAC-POWR607 device operates with analog and digital core power supplies of 3.3V, To simplify evaluation work, the evaluation board was designed to operate from a single 4.5V to 9V power supply, which may be brought in through a standard 5mm power plug (J2 - center tip positive). The evaluation board provides a linear regulator to provide the appropriate operating voltages for the ispPACPOWR607 device, as well as reverse polarity protection. The kit comes with a battery and cable that plugs into the connector at J2 and provides power with a 9V battery, see Figure 2. If it is desired to test the current in the power down mode of the ispPAC-POWR607, the link between pins 3 and 4 of J1 should be cut (please refer to Appendix A). Otherwise, approximately 2mA will be drawn when the device is in power down mode. Figure 2. 9V Battery Power Interface Input/Output Connections Connectors are provided for key functions and test points on this evaluation board, as shown In Figure 1. The JTAG programming cable is connected to a header (J3) in the lower right corner of the board. Access to the ispPAC-POWR607 device’s I/O pins is available along the left edge of the assembly, where a 2x17 block of pads (J1)supports the attachment of test probes or a ribbon-cable connector. In addition, there is an array of 70 proto-type holes for interfacing. Two momentary switches, S1 and S2, are provided on the evaluation board. They are connected to IN1_PWRDN and IN2 respectively. Several LEDs are also provided on the evaluation board to indicate proper function and as aids to debugging. LED D2 indicates that the on-board 3.3V supply is powered up. LED D3 is connected to the ispPACPOWR607 device’s TDO line, and will briefly flash when downloading, indicating that download data has made it to the device. Five LEDs are also provided on digital outputs OUT3 through OUT7 so that a user may easily view the progress of Sequence, Monitor, Reset programs run on the evaluation board. Demo Sequence and Reprogramming This evaluation board is shipped from the factory pre-programmed with the “ispPAC_POWR607_LED_Blinker.PAC” sequence from PAC-Designer’s library. The IN1_PWRDN button must be depressed in order t bring the ispPACPOWR607 device out of its power down mode. The programmed sequence will cause the LEDs to flash for about six seconds, and then the device will revert to the power down mode. In order to reprogram the ispPAC-POWR607, it must be brought out of power down mode. Thus, the IN1_PWRDN button must be depressed immediately before beginning a download to the device from PAC-Designer or ispVM. 3 ispPAC-POWR607 Evaluation Board User’s Guide Lattice Semiconductor Bill of Materials for the ispPAC-POWR607 Evaluation Board Ref Des Qty. 2 C1, C4 5 1 Description Dig-Key # or Equivalent 10µF 10V Tant. SMD capacitor 478-1751-1-ND C2, C3,C5,C6,C8 0.1µF SMD0603 ceramic capacitor PCC1762CT-ND D1 Diode Schottky 20V 1A SOD123Fl MBR120VLSFT10SCT-ND 1 R1 1k resistor SMD 0805 311-1.0KACT-ND 1 D2 GREEN LED SMD 1206 160-1404-1-ND 6 D3, 4, 5, 6, 7, 8 RED LED SMD 1206 160-1405-1-ND 1 J2 2.5mm power connector CP-102B-ND 1 RN1 Res Net 2k 14-pin SOIC 768-141-R2K-ND 2 R2, R3 10k resistor SMD 0805 311-10KACT-ND 2 R5, R6 4.7k resistor SMD 0805 311-4.7KACT-ND 1 J3 Header 36 pos .100 vert Gold Break into 8-pin used for JTAG WM6736-ND 2 SW1, SW2 Momentary push-button switches P10885SCT-ND 1 U1 ispPAC-POWR607 Lattice Semiconductor 1 U2 IC 3.3V LDO REG SOIC 296-2787-5-ND 1 N/A PCB 2” by 3.5” ispPAC-POWR607 Rev-2 Ordering Information • Part Number: PAC-POWR607-EV References • ispPAC-POWR607 Data Sheet Technical Support Assistance Hotline: 1-800-LATTICE (North America) +1-503-268-8001 (Outside North America) e-mail: [email protected] Internet: www.latticesemi.com Revision History Date Version May 2007 01.0 Change Summary Initial release. © 2007 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 4 5 A B C D 5 4 TDO 5 TCK TMS TDI R6 4.7k R5 4.7k HEADER 17X2 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 1 2 3 4 5 6 7 8 VCC 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 JTAG Interface J3 IN_OUT7 IN_OUT6 IN_OUT5 IN_OUT4 IN_OUT3 IN2 IN1_PWRDN HVOUT1 HVOUT2 VMON1 VMON2 VMON3 VMON4 VMON5 VMON6 4 100 100 VMON1 VMON2 VMON3 VMON4 VMON5 VMON6 TDI TDO R7 TMS TCK R4 IN1_PWRDN IN2 VCC is jumpered to 3.3V at pins 1 and 2 of J1 on the backside of the board. To measure the device power down current, cut the jumper trace on the backside of the board and connect an ammenter between pins 1 and 2. In addition, cut the jumper on the backside betweeen pins 3 and 4 of J1 to disconnect VCCJ. Replace with jumper blocks for normal operation. VCC 3.3V J1 VCCJ 3 VCC C7 50pF 18 14 19 15 29 28 2 3 5 6 7 10 3 C5 100n TDI TDO TMS TCK IN1 IN2 21 4 13 HVOUT1 HVOUT2 VCCJ C6 100n Date: Size A Title 27 26 23 22 20 30 31 IN_OUT3 IN_OUT4 IN_OUT5 IN_OUT6 IN_OUT7 HVOUT1 HVOUT2 2 Document Number ispPAC-POWR0607 Evaluation Board ispPAC-POWR0607 C8 100n 11 12 VCCJ GNDA IN/OUT3 IN/OUT4 IN/OUT5 IN/OUT6 IN/OUT7 ispPAC-POWR0607 VCCA VCCJ GNDD VCCD VMON1 VMON2 VMON3 VMON4 VMON5 VMON6 U1 VCC 2 Sheet 1 1 1 of 3 Rev 3 A B C D Lattice Semiconductor ispPAC-POWR607 Evaluation Board User’s Guide Appendix A. Schematics The following figures comprise the schematics for the ispPAC-POWR607 evaluation board. Figure 3 shows the device schematic and JTAG interface, while Figure 4 shows the on-board power-supply circuitry and the LED display. Figure 3. ispPAC-POWR607 Device Schematic 6 A B C 5 IN1_PWRDN IN_OUT3 IN_OUT4 IN_OUT5 IN_OUT6 IN_OUT7 TDO 1 2 3 PWR JACK R2 10k 2 4 3 4 SW4 IN1_PWRDN (RED) (RED) (RED) 1 D11 OUT5 C2 100n D10 OUT4 C1 10u 10V 3 4 D9 OUT3 MBR130p D1 4 1 2 3 4 5 6 7 IN IN IN2 2k X 13 RN1 OUT OUT TPS77733 Regulator U2 GND Enb 1 2 D J2 5 R3 10k 14 13 12 11 10 9 8 C3 100n 6 5 3 3 3.3V 2 1 C4 10u 10V 1k R1 (RED) D12 OUT6 3.3V 3 4 Date: Size A Title SW3 IN2 (RED) D13 OUT7 D14 TDO LEDs 2 Document Number ispPAC-POWR0607 Evaluation Board Power Supply and LEDs (RED) (GREEN) D2 PWR 2 Sheet 3 1 1 of 3 Rev 3 A B C D Lattice Semiconductor ispPAC-POWR607 Evaluation Board User’s Guide Figure 4. Power Supply and LEDs