ISL28166, ISL28266 ® Data Sheet August 29, 2008 39µA Micropower Single and Dual Rail-to-Rail Input-Output Low Input Bias Current (RRIO) Op Amps The ISL28166 and ISL28266 are micropower precision operational amplifiers optimized for single supply operation at 5V and can operate down to 2.4V. These devices feature an Input Range Enhancement Circuit (IREC), which enables them to maintain CMRR performance for input voltages greater than the positive supply. The input signal is capable of swinging 0.5V above a 5.0V supply (0.25 for a 2.5V supply) and to within 10mV from ground. The output operation is rail-to-rail. The 1/f corner of the voltage noise spectrum is at 1kHz. This results in low frequency noise performance, which can only be found on devices with an order of magnitude higher than the supply current. ISL28166 and ISL28266 can be operated from one lithium cell or two Ni-Cd batteries. The input range includes both positive and negative rail. The output swings to both rails. Ordering Information PART NUMBER (Note) PART MARKING FN6155.4 Features • 39µA typical supply current (ISL28166) • 78µA typical supply current (ISL28266) • 5nA max input bias current • 250kHz gain bandwidth product (AV = 1) • 2.4V to 5V single supply voltage range • Rail-to-rail input and output • Enable pin (ISL28166 only) • Pb-free (RoHS compliant) Applications • Battery- or solar-powered systems • 4mA to 20mA current loops • Handheld consumer products • Medical devices • Sensor amplifiers • ADC buffers PACKAGE (Pb-Free) PKG. DWG. # ISL28166FHZ-T7* GABY 6 Ld SOT-23 MDP0038 ISL28266FUZ 8266Z 8 Ld MSOP MDP0043 ISL28266FUZ-T7* 8266Z 8 Ld MSOP MDP0043 ISL28266FBZ 28266 FBZ 8 Ld SOIC MDP0027 ISL28266FBZ-T7* 28266 FBZ 8 Ld SOIC MDP0027 • DAC output amplifiers Pinouts ISL28166 (6 LD SOT-23) TOP VIEW OUT 1 V- 2 + - IN+ 3 *Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 5 ENABLE 4 IN- ISL28266 (8 LD SOIC) TOP VIEW ISL28266 (8 LD MSOP) TOP VIEW OUT_A 1 IN-_A 2 IN+_A 3 V- 4 1 6 V+ 8 V+ - + + - OUT_A 1 7 OUT_B IN-_A 2 6 IN-_B IN+_A 3 5 IN+_B V- 4 8 V+ 7 OUT_B - + + - 6 IN-_B 5 IN+_B CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2006, 2007, 2008. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. ISL28166, ISL28266 Absolute Maximum Ratings (TA = +25°C) Thermal Information Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V Supply Turn-on Voltage Slew Rate . . . . . . . . . . . . . . . . . . . . . 1V/µs Differential Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . V- - 0.5V to V+ + 0.5V ESD Rating Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3kV Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300V Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1500V Thermal Resistance (Typical Note 1) θJA (°C/W) 6 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . . 230 8 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . . . 160 8 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . 120 Output Short-Circuit Duration . . . . . . . . . . . . . . . . . . . . . . .Indefinite Ambient Operating Temperature Range . . . . . . . . .-40°C to +125°C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . +125°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTE: 1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER V+ = 5V, V- = 0V,VCM = 2.5V, TA = +25°C unless otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +125°C. Temperature data established by characterization. DESCRIPTION CONDITIONS MIN (Note 2) TYP MAX (Note 2) UNIT VOS Input Offset Voltage ΔV OS --------------ΔT Input Offset Drive vs Temperature IOS Input Offset Current -1.5 -5 0.34 1.2 2.5 nA IB Input Bias Current -5 -5.5 1.14 5 5.5 nA EN Input Noise Voltage Density FO = 1kHz 46 nV/√Hz IN Input Noise Current Density FO = 1kHz 0.14 pA/√Hz CMIR Input Common-Mode Voltage Range CMRR Common-Mode Rejection Ratio VCM = 0V to 5V 80 75 110 dB PSRR Power Supply Rejection Ratio VS = 2.4V to 5V 90 75 104 dB AVOL Large Signal Voltage Gain VO = 0.5V to 4.5V, RL = 100kΩ 200 175 412 V/mV VO = 0.5V to 4.5V, RL = 1kΩ 35 30 70 V/mV VOUT Maximum Output Voltage Swing -700 -800 Slew Rate GBW Gain Bandwidth Product 2 700 800 1.5 0 Output low, RL = 100kΩ Output low, RL = 1kΩ SR -7 µV µV/°C 5 V 3 6 8 mV 130 150 200 mV Output high, RL = 100kΩ 4.992 4.99 4.995 V Output high, RL = 1kΩ 4.85 4.8 4.88 V 0.05 V/µs 250 kHz AV = 1 FN6155.4 August 29, 2008 ISL28166, ISL28266 Electrical Specifications PARAMETER V+ = 5V, V- = 0V,VCM = 2.5V, TA = +25°C unless otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +125°C. Temperature data established by characterization. (Continued) DESCRIPTION MIN (Note 2) CONDITIONS TYP MAX (Note 2) UNIT IS,ON Supply Current, Enabled (ISL28166) 39 47 56 µA IS,ON Supply Current (ISL28266) 78 94 112 µA IS,OFF Supply Current, Disabled (ISL28166) 10 14 16 µA IO+ Short-Circuit Output Current RL = 10Ω IO- Short-Circuit Output Current RL = 10Ω VSUPPLY Supply Operating Range Guaranteed by PSRR test VINH Enable Pin High Level (ISL28166) VINL Enable Pin Low Level (ISL28166) IENH Enable Pin Input Current (ISL28166) VEN = 5V IENL Enable Pin Input Current (ISL28166) VEN = 0V tEN Enable to output on-state delay time (ISL28166) VOUT = 1V (enable state); VEN = High to Low 10.8 µs tEN Enable to output off-state delay time (ISL28166) VOUT = 0V (disabled state) VEN = Low to High 0.1 µs 28 23 31 -26 2.4 mA -24 -18 mA 5 V 2 V 0.8 V 1 1.2 1.2 µA 16 25 30 nA NOTE: 2. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. Typical Performance Curves 3 RL = 1k 1 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 2 0 -1 RL = 10k -2 RL = 100k -3 -4 -5 -6 -7 -8 AV = 1 CL = 16.3pF VOUT = 10mVP-P 1k 10k 100k FREQUENCY (Hz) FIGURE 1. GAIN vs FREQUENCY vs RL 3 1M 8 7 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 CL = 63.3pF CL = 55.3pF CL = 49.3pF CL = 43.3pF CL = 38.3pF CL = 34.3pF AV = 1 RL = 10k VOUT = 10mVP-P 1k 10k 100k 1M FREQUENCY (Hz) FIGURE 2. GAIN vs FREQUENCY vs CL FN6155.4 August 29, 2008 ISL28166, ISL28266 Typical Performance Curves (Continued) 1 Rf = 1M, Rg = 1k, RL = 10k 60 RL = 10k CL = 16.3pF VOUT = 10mVP-P 50 Rf = 100k, Rg = 1k, RL = 10k GAIN (dB) 40 30 20 Rf = 9.09, Rg = 1k, RL = INF 10 0 Rf = 0, Rg = INF, RL = 10k -10 100 1k 10k 100k VS = 2.4V 0 NORMALIZED GAIN (dB) 70 1M -1 VS = 5V -2 -3 -4 -5 -6 AV = 1 RL = 10k -8 VOUT = 10mVP-P -9 1k 10k -7 1 0 -1 VOUT = 100mV VOUT = 1V -2 -3 -4 -5 AV = 1 RL = 1k CL = 16.3pF -6 -7 -8 1k -1 100k -3 -4 -5 -6 -7 -9 1M VOUT = 1V -2 -8 10k VOUT = 10mV 0 VOUT = 50mV NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 1 VOUT = 10mV 2 VOUT = 50mV AV = 1 RL = 10k CL = 16.3pF VOUT = 100mV 1k 10k FREQUENCY (Hz) 10 VOUT = 1V -2 -3 CMRR (dB) NORMALIZED GAIN (dB) -1 VOUT = 50mV -4 -5 -6 -8 -9 VOUT = 100mV AV = 1 RL = 100k CL = 16.3pF -7 1k 1M FIGURE 6. GAIN vs FREQUENCY vs VOUT VOUT = 10mV 0 100k FREQUENCY (Hz) FIGURE 5. GAIN vs FREQUENCY vs VOUT 1 1M FIGURE 4. GAIN vs FREQUENCY vs VS FIGURE 3. CLOSED LOOP GAIN vs FREQUENCY 3 100k FREQUENCY (Hz) FREQUENCY (Hz) AV = 1 0 RL = 10k CL = 16.3pF -10 VCM = 1VP-P PP -20 VS = 2.4V VS = 5V -30 -40 -50 -60 10k 100k FREQUENCY (Hz) FIGURE 7. GAIN vs FREQUENCY vs VOUT 4 1M -70 100 1k 10k FREQUENCY (Hz) 100k 1M FIGURE 8. CMRR vs FREQUENCY FN6155.4 August 29, 2008 ISL28166, ISL28266 Typical Performance Curves (Continued) 10 -20 -30 -10 PSRR- -40 -50 -20 -30 -40 -50 PSRR+ -70 -70 -80 100 1k 10k 100k -90 1M 100 1k FREQUENCY (Hz) INPUT CURRENT NOISE (pA/√Hz) 120 100 80 60 40 20 1 10 100 1k 1.2 1.0 0.8 0.6 0.4 0.2 0 10k 1 10 100 1k 10k FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 11. INPUT VOLTAGE NOISE vs FREQUENCY FIGURE 12. INPUT CURRENT NOISE vs FREQUENCY 24 0 AV = 1000 RF = 100k Ri = 100 RL = 10k -0.4 RF = Ri = RL = 10k AV = 2 CL = 16.3pF VOUT = 10mVP-P 22 SMALL SIGNAL (mV) -0.2 INPUT NOISE (µV) 1M 1.4 140 -0.6 -0.8 -1.0 20 18 16 14 12 -1.2 -1.4 100k FIGURE 10. PSRR vs FREQUENCY, VS = 5V 160 INPUT VOLTAGE NOISE (nV/√Hz) 10k FREQUENCY (Hz) FIGURE 9. PSRR vs FREQUENCY, VS = 2.4V 0 PSRR- -60 PSRR+ -60 -80 AV = 1 RL = 1k CL = 16.3pF VOUT = 1VP-P VS = 5V 0 PSRR (dB) -10 PSRR (dB) 10 AV = 1 RL = 1k CL = 16.3pF VOUT = 1VP-P VS = 2.4V 0 0 1 2 3 4 5 6 7 8 TIME (s) FIGURE 13. 1Hz TO 10Hz INPUT NOISE 5 9 10 10 0 50 100 150 200 250 300 350 400 TIME (µs) FIGURE 14. SMALL SIGNAL STEP RESPONSE FN6155.4 August 29, 2008 ISL28166, ISL28266 6 0.4 5 1.0 V-ENABLE 4 0.2 0 -0.2 RF = Ri = RL = 10k AV = 2 CL = 16.3pF VOUT = 1VP-P -0.4 -0.6 1.2 0 100 0.8 3 2 1 0.4 0.2 0 200 300 400 -1 0 VOUT 0 10 20 30 40 50 60 70 80 90 -0.2 100 TIME (µs) TIME (µs) FIGURE 15. LARGE SIGNAL STEP RESPONSE FIGURE 16. ENABLE TO OUTPUT DELAY 85 66.5 n = 50 n = 1000 80 56.5 MAX MAX CURRENT (µA) CURRENT (µA) 0.6 RF = Ri = RL = 10k AV = 2 CL = 16.3pF VOUT = 10mVP-P OUTPUT (V) 0.6 ENABLE (V) LARGE SIGNAL (V) Typical Performance Curves (Continued) 46.5 MEDIAN 36.5 MIN 26.5 16.5 6.5 -40 75 70 MEDIAN 65 MIN 60 55 -20 0 20 40 60 80 100 50 -40 120 -20 0 TEMPERATURE (°C) FIGURE 17. SUPPLY CURRENT ENABLED (SINGLE) vs TEMPERATURE, VS = ±2.5V 40 60 80 100 120 FIGURE 18. SUPPLY CURRENT ENABLED (DUAL) vs TEMPERATURE, VS = ±2.5V 14.5 n = 1000 20 TEMPERATURE (°C) 350 MAX n = 50 13.5 250 MAX VOS (µV) CURRENT (µA) 12.5 11.5 MEDIAN 10.5 MEDIAN 50 -50 9.5 -150 8.5 MIN 7.5 6.5 -40 150 -250 MIN -20 0 20 40 60 80 TEMPERATURE (°C) 100 120 FIGURE 19. SUPPLY CURRENT DISABLED (SINGLE) vs TEMPERATURE, VS = ±2.5V 6 -350 -40 -20 0 20 40 60 80 TEMPERATURE (°C) 100 120 FIGURE 20. VOS vs TEMPERATURE, VS = ±2.5V FN6155.4 August 29, 2008 ISL28166, ISL28266 Typical Performance Curves (Continued) 400 5 MAX n = 50 300 n = 50 IBIAS+ (nA) 200 VOS (µV) MAX 4 100 MEDIAN 0 -100 3 MEDIAN 2 1 0 MIN -200 -1 -300 -40 -20 0 20 40 60 80 100 -2 -40 120 MIN -20 0 TEMPERATURE (°C) FIGURE 21. VOS vs TEMPERATURE, VS = ±1.2V 80 n = 50 MAX 4 100 120 MAX 1 IBIAS+ (nA) 3 IBIAS- (nA) 60 2 n = 50 MEDIAN 2 1 0 MEDIAN -1 -2 0 -1 -3 MIN -20 0 20 40 60 MIN 80 100 -4 -40 120 -20 0 20 40 60 80 100 120 TEMPERATURE (°C) TEMPERATURE (°C) FIGURE 23. IBIAS- vs TEMPERATURE, VS = ±2.5V 2 40 FIGURE 22. IIBIAS+ vs TEMPERATURE, VS = ±2.5V 5 -2 -40 20 TEMPERATURE (°C) FIGURE 24. IBIAS+ vs TEMPERATURE, VS = ±1.2V 3 n = 50 MAX 2.5 1 n = 50 2 MEDIAN 1.5 -1 IOS (nA) IBIAS- (nA) 0 -2 0.5 MEDIAN 0 -0.5 -3 -1 -4 -5 -40 MAX 1 MIN -20 0 20 40 60 80 100 120 TEMPERATURE (°C) FIGURE 25. IBIAS- vs TEMPERATURE, VS = ±1.2V 7 MIN -1.5 -2 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (°C) FIGURE 26. IOS vs TEMPERATURE, VS = ±2.5V FN6155.4 August 29, 2008 ISL28166, ISL28266 Typical Performance Curves (Continued) 2.5 140 n = 50 130 1.5 MAX CMRR (dB) MEDIAN 0.5 MAX 125 1.0 IOS (nA) n = 50 135 2.0 0 -0.5 120 115 MEDIAN 110 105 -1.0 MIN 100 MIN -1.5 -2.0 -40 -20 0 20 95 40 60 80 100 90 -40 120 -20 0 FIGURE 27. IOS vs TEMPERATURE, VS = ±1.2V 135 20 40 60 80 100 120 TEMPERATURE (°C) TEMPERATURE (°C) FIGURE 28. CMRR vs TEMPERATURE V+ = ±2.5V, ±1.5V 4.9 n = 50 n = 50 130 4.89 125 MAX MAX 4.88 VOUT (V) PSRR (dB) 120 115 110 MEDIAN 105 4.87 MEDIAN 4.86 100 MIN MIN 95 4.85 90 4.84 -40 85 -40 -20 0 20 40 60 80 100 120 -20 0 4.9965 60 80 100 120 170 n = 50 n = 50 160 4.996 MAX MAX 150 VOUT (m V) 4.9955 VOUT (V) 40 FIGURE 30. VOUT HIGH vs TEMP VS = ±2.5V, RL = 1k FIGURE 29. PSRR vs TEMPERATURE ±1.2V TO ±2.5V 4.995 MEDIAN 4.9945 140 MEDIAN 130 MIN 120 MIN 4.994 4.9935 -40 20 TEMPERATURE (°C) TEMPERATURE (°C) 110 -20 0 20 40 60 80 100 TEMPERATURE (°C) FIGURE 31. VOUT HIGH VS = ±2.5V, RL = 100k 8 120 100 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (°C) FIGURE 32. VOUT LOW VS = ±2.5V, RL = 1k FN6155.4 August 29, 2008 ISL28166, ISL28266 Typical Performance Curves (Continued) 4.5 n = 50 4 VOUT (m V) MAX 3.5 3 MEDIAN MIN 2.5 2 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (°C) FIGURE 33. VOUT LOW VS = ±2.5V, RL = 100k Pin Descriptions ISL28166 (6 Ld SOT-23) ISL28266 (8 Ld SOIC) (8 Ld MSOP) PIN NAME 2 (A) 6 (B) ININ-_A IN-_B 4 FUNCTION EQUIVALENT CIRCUIT Inverting input V+ IN- IN+ VCircuit 1 3 (A) 5 (B) IN+ IN+_A IN+_B 4 V- 1 (A) 7 (B) OUT OUT_A OUT_B 3 2 1 Non-inverting input (See Circuit 1) Negative supply Output V+ OUT VCircuit 2 6 8 5 V+ ENABLE Positive supply Chip enable V+ CE VCircuit 3 9 FN6155.4 August 29, 2008 ISL28166, ISL28266 Applications Information Introduction The ISL28166 is a single BiMOS rail-to-rail input, output (RRIO) operational amplifier with an enable feature. The ISL28266 is a dual version without the enable feature. Both devices are designed to operate from single supply (2.4V to 5.0V) or dual supplies (±1.2V to ±2.5V) while drawing only 39µA of supply current per amplifier. This combination of low power and precision performance makes this device suitable for a variety of low power applications including battery powered systems. result in higher than expected supply currents and possible noise injection into the channel being used. The proper way to prevent this oscillation is to short the output to the negative input and ground the positive input (as shown in Figure 35). + FIGURE 35. PREVENTING OSCILLATIONS IN UNUSED CHANNELS Rail-to-Rail Input/Output These devices feature bi-polar inputs which have an input common mode range that extends to the rails, and CMOS outputs that can typically swing to within about 4mV of the supply rails with a 100kΩ load. The NMOS sinks current to swing the output in the negative direction. The PMOS sources current to swing the output in the positive direction. Current Limiting Input Protection It is possible to exceed the +125°C maximum junction temperatures under certain load and power-supply conditions. It is therefore important to calculate the maximum junction temperature (TJMAX) for all applications to determine if power supply voltages, load conditions, or package type need to be modified to remain in the safe operating area. These parameters are related in Equation 1: All input terminals have internal ESD protection diodes to both positive and negative supply rails, limiting the input voltage to within one diode beyond the supply rails. They also contain back-to-back diodes across the input terminals. For applications where the input differential voltage is expected to exceed 0.5V, external series resistors must be used to ensure the input currents never exceed 5mA (Figure 34). VIN VOUT RIN RL + FIGURE 34. INPUT CURRENT LIMITING Enable/Disable Feature The ISL28166 offers an EN pin that disables the device when pulled up to at least 2.0V. In the disabled state (output in a high impedance state), the part consumes typically 10µA. By disabling the part, multiple ISL28166 parts can be connected together as a MUX. In this configuration, the outputs are tied together in parallel and a channel can be selected by the EN pin. The EN pin also has an internal pull-down. If left open, the EN pin will pull to the negative rail and the device will be enabled by default. The loading effects of the feedback resistors of the disabled amplifier must be considered when multiple amplifier outputs are connected together. Using Only One Channel The ISL28266 is a dual op amp. If the application only requires one channel, the user must configure the unused channel to prevent it from oscillating. The unused channel will oscillate if the input and output pins are floating. This will 10 These devices have no internal current-limiting circuitry. If the output is shorted, it is possible to exceed the Absolute Maximum Rating for output current or power dissipation, potentially resulting in the destruction of the device. Power Dissipation T JMAX = T MAX + ( θ JA xPD MAXTOTAL ) (EQ. 1) where: • PDMAXTOTAL is the sum of the maximum power dissipation of each amplifier in the package (PDMAX) • PDMAX for each amplifier can be calculated using Equation 2: V OUTMAX PD MAX = 2*V S × I SMAX + ( V S - V OUTMAX ) × ---------------------------RL (EQ. 2) where: • TMAX = Maximum ambient temperature • θJA = Thermal resistance of the package • PDMAX = Maximum power dissipation of 1 amplifier • VS = Supply voltage • IMAX = Maximum supply current of 1 amplifier • VOUTMAX = Maximum output voltage swing of the application • RL = Load resistance FN6155.4 August 29, 2008 ISL28166, ISL28266 SOT-23 Package Family MDP0038 e1 D SOT-23 PACKAGE FAMILY A MILLIMETERS 6 N SYMBOL 4 E1 2 E 3 0.15 C D 1 2X 2 3 0.20 C 5 2X e 0.20 M C A-B D B b NX 0.15 C A-B 1 3 SOT23-5 SOT23-6 A 1.45 1.45 MAX A1 0.10 0.10 ±0.05 A2 1.14 1.14 ±0.15 b 0.40 0.40 ±0.05 c 0.14 0.14 ±0.06 D 2.90 2.90 Basic E 2.80 2.80 Basic E1 1.60 1.60 Basic e 0.95 0.95 Basic e1 1.90 1.90 Basic L 0.45 0.45 ±0.10 L1 0.60 0.60 Reference N 5 6 Reference D 2X TOLERANCE Rev. F 2/07 NOTES: C A2 2. Plastic interlead protrusions of 0.25mm maximum per side are not included. SEATING PLANE A1 0.10 C 1. Plastic or metal protrusions of 0.25mm maximum per side are not included. 3. This dimension is measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. NX 5. Index area - Pin #1 I.D. will be located within the indicated zone (SOT23-6 only). (L1) 6. SOT23-5 version has no center lead (shown as a dashed line). H A GAUGE PLANE c L 11 0.25 0° +3° -0° FN6155.4 August 29, 2008 ISL28166, ISL28266 Small Outline Package Family (SO) A D h X 45° (N/2)+1 N A PIN #1 I.D. MARK E1 E c SEE DETAIL “X” 1 (N/2) B L1 0.010 M C A B e H C A2 GAUGE PLANE SEATING PLANE A1 0.004 C 0.010 M C A B L b 0.010 4° ±4° DETAIL X MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SYMBOL SO-14 SO16 (0.300”) (SOL-16) SO20 (SOL-20) SO24 (SOL-24) SO28 (SOL-28) TOLERANCE NOTES A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX - A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 ±0.003 - A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 ±0.002 - b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 ±0.003 - c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 ±0.001 - D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 ±0.004 1, 3 E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 ±0.008 - E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 ±0.004 2, 3 e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic - L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 ±0.009 - L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic - h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference - 16 20 24 28 Reference - N SO-8 SO16 (0.150”) 8 14 16 Rev. M 2/07 NOTES: 1. Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 12 FN6155.4 August 29, 2008 ISL28166, ISL28266 Mini SO Package Family (MSOP) 0.25 M C A B D MINI SO PACKAGE FAMILY (N/2)+1 N E MDP0043 A E1 MILLIMETERS PIN #1 I.D. 1 B (N/2) e H C SEATING PLANE 0.10 C N LEADS SYMBOL MSOP8 MSOP10 TOLERANCE NOTES A 1.10 1.10 Max. - A1 0.10 0.10 ±0.05 - A2 0.86 0.86 ±0.09 - b 0.33 0.23 +0.07/-0.08 - c 0.18 0.18 ±0.05 - D 3.00 3.00 ±0.10 1, 3 E 4.90 4.90 ±0.15 - E1 3.00 3.00 ±0.10 2, 3 e 0.65 0.50 Basic - L 0.55 0.55 ±0.15 - L1 0.95 0.95 Basic - N 8 10 Reference - 0.08 M C A B b Rev. D 2/07 NOTES: 1. Plastic or metal protrusions of 0.15mm maximum per side are not included. L1 2. Plastic interlead protrusions of 0.25mm maximum per side are not included. A 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. c SEE DETAIL "X" A2 GAUGE PLANE L A1 0.25 3° ±3° DETAIL X All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 13 FN6155.4 August 29, 2008