Application Note AN-1158 IRS2053M Functional Description By Jun Honda, Xiao-chang Cheng Table of Contents 1 IRS2053M General Description................................................................................................................... 2 Typical Implementation ........................................................................................................................... 3 2 Input Section................................................................................................................................................ 4 2.1 OTA (Operating Trans-conductance Amplifier)....................................................................................... 5 2.2 PWM Modulator....................................................................................................................................... 5 2.3 Clock Synchronization............................................................................................................................. 7 2.4 DS (Delay Select) pin.............................................................................................................................. 8 2.5 Click Noise Elimination............................................................................................................................ 8 2.6 CSD Voltage and OTA Operational Mode .............................................................................................. 9 2.7 Self-oscillation Start-up Condition ........................................................................................................... 9 3 MOSFET Selection.................................................................................................................................... 10 4 Over Current Protection (OCP) ................................................................................................................. 11 4.1 Protection Control.................................................................................................................................. 12 4.2 Programming OCP Trip Level ............................................................................................................... 16 5 Over Temperature Protection .................................................................................................................... 20 6 DC Offset Protection.................................................................................................................................. 21 7 Fault Output ............................................................................................................................................... 21 8 CLIP Output ............................................................................................................................................... 21 9 Deadtime Design ....................................................................................................................................... 23 9.1 How to Determine Optimal Deadtime ................................................................................................... 23 9.2 Programming Deadtime ........................................................................................................................ 24 10 Power Supply Considerations ................................................................................................................... 25 10.1 Supplying VAA and VSS ...................................................................................................................... 25 10.2 Recommended Power Supply Configuration for Gate Driver Stage ................................................ 26 10.3 Designing High-side Bootstrap Power Supply.................................................................................. 28 10.4 Start-up Sequence (UVLO)............................................................................................................... 33 10.5 Power Supply Decoupling................................................................................................................. 34 11 Junction Temperature Estimation.............................................................................................................. 35 11.1 PMID: Power Dissipation of the Input Floating Logic and Protection Circuitry ................................... 35 11.2 PLSM: Power Dissipation of the Input Level Shifter............................................................................ 35 11.3 PLOW: Power Dissipation of Low Side ............................................................................................... 35 11.4 PLSH: Power Dissipation of the High-side Level Shifter..................................................................... 36 11.5 PHIGH: Power Dissipation of High Side .............................................................................................. 36 11.6 PD: Total Power Dissipation .............................................................................................................. 36 11.7 TJ: Junction Temperature.................................................................................................................. 37 12 Board Layout Considerations .................................................................................................................... 38 12.1 Ground Plane.................................................................................................................................... 39 1.1 www.irf.com AN-1158 1 1 IRS2053M General Description The IRS2053M is a three channel Class D audio amplifier driver with integrated PWM modulators and over current protection. Combined with six external MOSFETs and external passive components, the IRS2053M forms three complete Class D amplifiers. The versatile structure of the analog input section with an error amplifier and a PWM comparator has flexibility of implementing different types of PWM modulator schemes. Loss-less current sensing utilizes RDS(on) of the MOSFETs. The protection control logic monitors the status of the power supplies and load current through each MOSFET. For the convenience of half bridge configuration, the analog PWM modulator and protection logic are constructed on a floating well. The IRS2053M implements start-up click noise reduction to suppress unwanted audible noise during PWM startup and shutdown. Figure 1 Functional Block Diagram of IRS2053M www.irf.com AN-1158 2 1.1 Typical Implementation The following explanations are based on a typical application circuit with self-oscillating PWM topology shown in Figure 2. For further information on the design, refer to the IRAUDAMP11 reference design. CH3 INPUT +5V -5V SIGNAL GND CH2 INPUT CH1 INPUT FAULT CH1 CLIP CH2 CLIP CH3 CLIP CH3 OUTPUT POWER GND -B CH1 OUTPUT CH2 OUTPUT +B VCC CLK INPUT (optional) Figure 2 IRS2053M Typical Application Circuit www.irf.com AN-1158 3 2 Input Section The audio input stage of the IRS2053M is configured as an inverting error amplifier. In Figure 3, the voltage gain of the amplifier GV is determined by input resistor RIN and feedback resistor RFB. GV RFB RIN Since the feedback resistor RFB is part of an integrator time constant, which determines switching frequency, changing overall voltage gain by RIN is simpler and, therefore, recommended in most cases. Note that the input impedance of the amplifier is equal to the input resistor RIN. A DC blocking capacitor C3 should be connected in series with RIN to minimize DC offset in the output. Minimizing DC offset is essential for audible noise-less Turn-ON and -OFF. A ceramic capacitor is not recommended due to the potential cause of distortion. The connection of the non-inverting input IN+ is a reference for the error amplifier, and thus is crucial for audio performance. Connect IN+ to the signal reference ground in the system, which has the same potential as the negative terminal of the speaker output. Figure 3 IRS2053M Typical Control Loop Design www.irf.com AN-1158 4 2.1 OTA (Operating Trans-conductance Amplifier) The front-end error amplifier of the IRS2053M features an operational trans-conductance amplifier (OTA), which is carefully designed to obtain optimal audio performance. The OTA outputs a current to the COMP pin, unlike a voltage output in an operational amplifier (OPA). The non-inverting input is internally tied to the GND pin. The inverting input has clamping diodes to GND to improve recovery from clipping as well as ensuring stable start up. The OTA output COMP is internally connected to the PWM comparator whose threshold is (VAAVSS)/2. For stable operation of the OTA, a compensation capacitor Cc minimum of 1nF is required. The OTA shuts down when VCSD<Vth2. 2.2 PWM Modulator The IRS2053M allows the user to choose from numerous ways of PWM modulator implementations. In this section, all the explanations are based on a typical application circuit of a self-oscillating PWM. 2.2.1 Self-Oscillating PWM Modulator Design The typical application features a self-oscillating PWM scheme. For better audio performance, front end 2nd order integration is chosen. 2.2.2 Self-Oscillating Frequency Self-oscillating frequency is determined mainly by the following items in Figure 3. Integration capacitors, C1 and C2 Integration resistor, R1 Propagation delay in the gate driver Feedback resistor, RFB Duty cycle The bus voltage and input resistance RIN have little influence on the self-oscillating frequency. Note that as is the nature of a self-oscillating PWM, the switching frequency decreases as PWM modulation deviates from idling. www.irf.com AN-1158 5 2.2.3 Determining Self-Oscillating Frequency Choosing the switching frequency entails making many design trade offs. At lower switching frequencies, the efficiency at the MOSFET stage improves, but inductor ripple current increases. Also output PWM switching carrier leakage increases. At higher switching frequencies the efficiency degrades due to switching losses, but wider bandwidth can be achieved. The inductor ripple decreases yet iron losses increase. The junction temperature of the gate driver IC might be a stopper for going to a higher frequency. For these reasons, 400kHz is chosen for a typical design example, which can be seen in the IRAUDAMP8 reference design. 2.2.4 Choosing External Components Value For suggested component values of components for a given target self-oscillating frequency, refer to Table 1. The OTA output has limited voltage and current compliances. This set of component values ensures that the OTA operates within its linear region so optimal THD+N performance can be achieved. In case the target frequency is somewhere in between the frequencies listed in Table 1, adjust the frequency by tweaking R1, if necessary. Target SelfOscillation Frequency (kHz) 500 450 400 350 300 250 200 150 100 70 C1=C2 (nF) 2.2 2.2 2.2 2.2 2.2 2.2 4.7 10 10 22 R1 (ohms) 200 165 141 124 115 102 41.2 20.0 14.0 4.42 Condition:IRS2053M with IRF6665, DS=VAA, Vbus=+/-35V, DT=25ns, RFB=47k. Table 1 External Component Values vs. Self Oscillation Frequency www.irf.com AN-1158 6 2.3 Clock Synchronization In the PWM control loop design example, the self-oscillating frequency can be set and synchronized to an external clock. Through a set of resistors and a capacitor, the external clock injects periodic pulsating charges into the integrator, forcing oscillation to lock up to the external clock frequency. A typical setup with 5Vp-p 50% duty clock signal uses RCK=22k and CCK=100pF in Figure 4. To maximize audio performance, the self-running frequency without clock injection should be 20 to 30% higher than the external clock frequency. EXT. CLK RCK C1 CCK C2 R1 COMP Vin RIN INGND + RFB Figure 4 External Clock Sync Figure 5 shows how a self-oscillating frequency locks up to an external clock frequency. A design of a400kHz self-oscillating frequency synchronizes to an external clock whose frequency is within the red boarder lines. 600 Operating Frequency (kHz) 500 400 300 200 100 0 10% 20% 30% 40% 50% 60% 70% 80% 90% Duty Cycle Figure 5 Typical Lock Range to External Clock www.irf.com AN-1158 7 2.4 DS (Delay Select) pin The DS pin offers options to bypass an internal delay block to achieve shorter latency, as shown in Table 2. DS Pin VAA VSS Propagation Delay (TYP) 325 ns 100 ns Table 2 Propagation Delay and DS pin Bias 2.5 Click Noise Elimination The IRS2053M has a unique feature that minimizes Turn-ON and -OFF audible click noise. When CSD is in between Vth1 and Vth2 during start up, an internal closed loop around the OTA enables an oscillation that generates voltages at COMP and IN-, bringing them to steady state values. It runs at around 1MHz, independent from the switching oscillation. Figure 5 Click Noise Elimination As a result, all capacitive components connected to COMP and IN- pins, such as C1, C2, C3 and Cc in Figure 5, are pre-charged to their steady state values during the start up sequence. This allows instant settling of PWM operation. To utilize the click noise reduction function, the following conditions must be met. 1. CSD pin has slow enough ramp up from Vth1 to Vth2 such that the voltages in the capacitors can settle to their target values. 2. High-side bootstrap power supply needs to be charged up prior to starting oscillation. 3. Audio input has to be zero. 4. For internal local loop to override external feedback during the startup period, DC offset at speaker output prior to shutdown release has to satisfy the following condition. DCoffset 30A RFB www.irf.com AN-1158 8 2.6 CSD Voltage and OTA Operational Mode The CSD pin determines the operational mode of the IRS2053M as shown in Figure 6. The OTA has three operational modes; cut off, local oscillation and normal operation while the gate driver section has two modes; normal and shutdown with CSD voltage. When VCSD < Vth2, the IC is in shutdown mode and the OTA is cut off. When Vth2< VCSD < Vth1, the HO and LO outputs are still in shutdown mode. The OTA is activated and starts local oscillation, which pre-biases all the capacitive components in the error amplifier. When VCSD>Vth1, shutdown is released and PWM operation starts. Figure 6 VCSD and OTA Mode 2.7 Self-oscillation Start-up Condition The IRS2053M requires the following conditions be met to start PWM oscillation in the typical application circuit. - All the control power supplies, VAA, VSS, VCC and VBS are above the under voltage lockout thresholds. CSD pin voltage is over Vth1 threshold. iIN iFB Where iIN VIN V , i FB B . RIN RFB Note that this condition also limits the maximum audio input voltage feeding into R1. If this condition is exceeded, the amplifier stops its oscillation during the operation period. This allows a 100% modulation index; however, care should be taken so that the high-side floating supply does not decay due to a lack of low-side pulse ON state. www.irf.com AN-1158 9 3 MOSFET Selection There are a couple of limitations on the size of the MOSFET to be used with the IRS2053M. 1. Power dissipation Power dissipation from the gate driver stage in the IRS2053M is proportional to switching frequency and the gate charge of the MOSFET. The higher the switching frequency, the lower the gate charge of the MOSFET that can be used. Refer to Junction Temperature Estimation later in this application note for details. 2. Switching Speed Internal over current protection has a certain time window to measure the output current. If switching transition takes too long, the internal OCP circuitry starts monitoring voltage across the MOSFET which induces false triggering of OCP. Less than 20nC of gate charge per output is recommended. The IRS2053M accommodates a range of IR Digital Audio MOSFETs, providing a scalable design for various output power levels. For further information on MOSFET section, refer to AN-1070, Class D Amplifier Performance Relationship to MOSFET Parameters. www.irf.com AN-1158 10 4 Over Current Protection (OCP) The IRS2053M features over current protection to protect the power MOSFETs during abnormal load conditions. The control logic is shown in Figure 8. The IRS2053M starts a sequence of events when it detects an over current condition during either high-side or low-side turn on of a pulse. As soon as either the high-side or low-side current sensing block detects over current: 1. The OC Latch (OCL) flips logic states and shutdowns the outputs LO and HO. 2. The CSD pin starts discharging the external capacitor Ct. 3. When VCSD, the voltage across Ct, falls below the lower threshold Vth2, an output signal from COMP2 resets OCL. 4. The CSD pin starts charging the external capacitor Ct. 5. When VCSD goes above the upper threshold Vth1, the logic on COMP1 flips and the IC resumes operation. As long as the over current condition exists, the IC will repeat the over current protection sequence at a repetition rate dependent upon capacitance at the CSD pin. Figure 7 Over Current Protection Timing Chart www.irf.com AN-1158 11 Figure 8 Shutdown Functional Block Diagram 4.1 Protection Control The internal protection control block dictates the operational mode, normal or shutdown, using the input of the CSD pin. In shutdown mode, the IC forces LO and HO to output 0V with respect to COM and VS respectively to turn off the power MOSFETs. The CSD pin provides five functions. 1. Power up delay timer 2. Self-reset timer 3. Shutdown input 4. Latched protection configuration 5. Shutdown status output (host I/F) The CSD pin cannot be paralleled with another IRS2053M. The operating statuses of the protections are shown in Table 3. www.irf.com AN-1158 12 Event UVCC, rising edge UVCC, falling edge UVAA, rising edge UVAA, falling edge UVBS, rising edge UVBS, falling edge Over Current Protection DC Protection Clip Detection OTP1-3 Inputs CSD recycle n/a n/a n/a n/a n/a keep recycling until OCP goes away held L until DCP goes away n/a keep recycling until OTP goes away FAULT L until CSD>Vth1 n/a L at VAA<UVAA L at VAA<UVAA n/a n/a held L until OCP goes away held L until DCP goes away n/a held L until OTP goes away *CSD recycle: CSD pin voltage discharges down to Vth2 and charges back to VAA, if CSD pin is configured as self reset protection. Table 3 Events and Actions of CSD and FAULT 4.1.1 Self Reset Protection By putting a capacitor between CSD and VSS, the IRS2053M resets itself after entering shutdown mode. After the OCP event, the CSD pin discharges Ct voltage VCSD down to the lower threshold Vth2 to reset the internal shutdown latch. Then, the IRS2053M begins to charge Ct in an attempt to resume operation. Once the voltage of the CSD pin rises above the upper threshold, Vth1, the IC resumes normal operation. Figure 9 Self Reset Protection Configuration www.irf.com AN-1158 13 4.1.2 Designing Ct The timing capacitor, Ct, is used to program tRESET and tSU. tRESET is the amount of time that elapses from when the IC enters the shutdown mode to the time when the IC resumes operation. tRESET should be long enough to avoid over heating the MOSFETs from the repetitive sequence of shutting down and resuming operation during over current conditions. In most of applications, the minimum recommended time for tRESET is 0.1 second. tSU is the amount of time between powering up the IC in shutdown mode to the moment the IC releases shutdown to begin normal operation. The Ct determines tRESET and tSU as following equations: t RESET t SU Ct V AA 1.1 I CSD Ct V AA 0.7 I CSD [s] [s] where ICSD = the charge/discharge current at the CSD pin VAA = the floating input supply voltage with respect to VSS. 4.1.3 Shutdown Input The IRS2053M can be shut down by an external shutdown signal SD. Figure 10 shows how to add an external discharging path to shutdown the PWM. Figure 10 Shutdown Input 4.1.4 Latched Protection Connecting CSD to VAA through a 10k Ω or less resistance configures the over current protection latch. The latch locks the IC in shutdown mode after over current is detected. An external reset switch can be used to bring CSD www.irf.com AN-1158 14 below the lower threshold Vth2 for a minimum of 200ns to properly reset the latch. After the power up sequence, a reset signal to the CSD pin is required to release the IC from the latched shutdown mode. VAA Vth1 <10k COMP1 ` CSD ` COMP2 SHUTDOWN Vth2 VSS Figure 11 Latched Protection with Reset Input www.irf.com AN-1158 15 4.1.5 Interfacing with System Controller The IRS2053M can communicate with an external system controller through a simple interfacing circuit shown in Figure 12. A generic PNP transistor U1 detects the sink current at the CSD pin during an OCP event and outputs a shutdown signal to an external system controller. Another generic NPN transistor U2 can then reset the internal protection logic by pulling the CSD voltage below the lower threshold Vth2 for a minimum of 200ns. Note that the CSD pin is configured to operate in latched OCP. After the power up sequence, a reset signal to the CSD pin is required to release the IC from the shutdown mode. Figure 12 Interfacing with Host Controller 4.2 Programming OCP Trip Level In a Class D audio amplifier, the direction of the load current alternates with the audio input signal. An overcurrent condition can therefore occur during either a positive current cycle or a negative current cycle. The IRS2053M uses the RDS(on) of the output MOSFETs as current sensing resistors. Due to the structural constraints of high voltage ICs, current sensing is implemented differently for the high side and low side. If the measured current exceeds a predetermined threshold, the OCP block outputs a signal to the protection block, forcing HO and LO low and protecting the MOSFETs. www.irf.com AN-1158 16 Figure 13 Bi-directional Over Current Protection 4.2.1 Low Side Over Current Sensing For negative load currents, low-side over current sensing monitors the load condition and shuts down switching operation if the load current exceeds the preset trip level. Low-side current sensing is based on the measurement of VDS across the low side MOSFET during the low-side on state. In order to avoid triggering OCP from overshoot, a blanking interval inserted after LO turn on disables over current detection for 450ns. The OCSET pin is to program the threshold for low-side over current sensing. When the measured VDS measured of the low side MOSFET exceeds the voltage at the OCSET pin with respect to COM, the IRS2053M begins the OCP sequence described earlier. Note that the programmable OCSET range is 0.5V to 5.0V. To disable the low side OCP, connect OCSET to VCC directly. To program the trip level for over current, the voltage at OCSET can be calculated using the equation below. VOCSET = VDS(LOW SIDE) = ITRIP+ x RDS(on) In order to minimize the effect of the input bias current at the OCSET pin, select resistor values for R4 and R5 such that the current through the voltage divider is 0.5mA or more. * Note: Using VREF to generate an input to OCSET through a resistive divider provides improved immunity from fluctuations in VCC. www.irf.com AN-1158 17 Figure 14 Low Side Over Current Sensing 4.2.2 Low Side Over Current Setting Assume that the low side MOSFET has RDS(on) of 100mΩ. VOCSET to set the current trip level at 30A is given by: VOCSET = ITRIP+ x RDS(on) = 30A x 100m = 3.0V Choose R4+R5=10 k to properly load the VREF pin. R5 VOCSET 10k VREF 3.0V 10k 5.1V 5.8k where VREF = 5.1V Based on the E-12 series resistor values, choose R5 = 5.6k and R4 = 3.9k to complete the design. In general, RDS(on) has a positive temperature coefficient that needs to be considered when setting the threshold level. Also, variations in RDS(on) will affect the selection of external or internal component values. www.irf.com AN-1158 18 4.2.3 High Side Over-Current Sensing For positive load currents, high-side over current sensing also monitors the load condition and shuts down switching operation if the load current exceeds the preset trip level. High-side current sensing is based on the measurement of VDS across the high-side MOSFET during high-side turn on through pins CSH and Vs. In order to avoid triggering OCP from overshoot, a blanking interval inserted after HO turn on disables over current detection for 450ns. In contrast to low-side current sensing, the threshold at which the CSH pin engages OC protection is internally fixed at 1.2V. An external resistive divider R2 and R3 can be used to program a higher threshold. An external reverse blocking diode, D1, is required to block high voltages from feeding into the CSH pin while the high side is off. Due to a forward voltage drop of 0.6V across D1, the minimum threshold required for high-side over current protection is 0.6V. VCSH R3 VDS ( HIGHSIDE) V F ( D1) R 2 R3 where VDS(HIGH SIDE) = the drain to source voltage of the high side MOSFET during high side turn on VF(D1) = the forward drop voltage of D1 Since VDS(HIGH SIDE) is determined by the product of drain current ID and RDS(on) of the high side MOSFET. VCSH can be rewritten as: VCSH R3 RDS ( ON ) I D VF ( D1) R 2 R3 The reverse blocking diode D1 is forward biased by a 10k resistor R1. Figure 15 Programming High Side Over Current Threshold www.irf.com AN-1158 19 4.2.4 High Side Over Current Setting Figure 15 demonstrates the typical circuitry used for high side current sensing. In the following example, the over current protection level is set to trip at 30A using a MOSFET with an RDS(on) of 100m. The component values of R2 and R3 can be calculated using the following formula: Let R2 + R3=10 k. R3 10k VthOCH V DS V F where VthOCL = 1.2V VF = the forward voltage of reverse blocking diode D1 = 0.6V. VDS@ID=30A = the voltage drop across the high side MOSFET when the MOSFET current is 30A. Therefore, VDS@ID=30A = ID x RDS(on) = 30A x 100m = 3V Based on the formulas above, R2 = 6.8k and R3 = 3.3k. 4.2.5 Choosing the Right Reverse Blocking Diode The selection of the appropriate reverse blocking diode D1 depends on its voltage rating and speed. To effectively block bus voltages, the reverse voltage must be higher than the voltage difference between +B and –B and the reverse recovery time must be as fast as the bootstrap charging diode. A diode such as the NXP BAV21W, a 200V, 50ns high speed switching diode, is more than sufficient. 5 Over Temperature Protection The three over temperature protection inputs OTP1, OTP2 and OTP3 monitor external PTC type temperature sensors. The PTC sensor can be arranged to monitor MOSFET temperatures on each channel. Each OTP pin supplies 0.6mA from an internal current source to bias an external PTC resistor. Over temperature protection is activated when the voltage at any OTP input pin goes higher than 2.8V. Figure 16 Over Temperature Protection Input Structure www.irf.com AN-1158 20 6 DC Offset Protection The DCP input detects excessive DC offset voltage at the speaker outputs and shuts down PWM operations. The DCP input is referenced to GND. If the input voltage exceeds the positive or negative detecting threshold, the DC offset protection shuts down PWM operations and reports a fault via the FAULT pin. Figure 17 DC Offset Protection Input Structure 7 Fault Output The FAULT output is an open drain output referenced to GND. Its purpose is to report whether the IRS2053M is in shutdown mode or in normal operating mode. If the FAULT pin is open, the IRS2053M is in normal operating mode. 8 CLIP Output When the output of the amplifier looses track of an expected target value, the amplifier enters clipping condition. The purpose of the CLIP output is to flag this condition. The voltage at the COMP pin is monitored with a window comparator. The drain of an open drain MOSFET at the CLIP pin is pulled to GND for 1uS plus the clip detection time when a clipping condition is detected. The detection threshold at the COMP pin is set at 10% and 90% of VAA-VSS. Each channel has independent CLIP outputs. The CLIP outputs are disabled when the IRS2053M is in shutdown mode. www.irf.com AN-1158 21 VAA IN-1 OTA GND COMP1 VSS VAA R CLIP1 PGEN 8R R VSS Figure 18 Clipping Detection www.irf.com AN-1158 22 9 Deadtime Design Dead time is the blanking period inserted between either high-side Turn-OFF and low-side Turn-ON, or low-side Turn-OFF and high-side Turn-ON. Its purpose is to prevent shoot through, or a rush of current through both MOSFETs. In the IRS2053M, an internal dead time generation block allows the user to select the optimum dead time from a range of preset values. Selecting a preset dead time through the DT pin voltage can easily be done through an external voltage divider. This way of setting dead time prevents outside noise from modulating the switching timing, which is critical to the audio performance. 9.1 How to Determine Optimal Deadtime The effective deadtime in an actual application differs from the deadtime specified in this datasheet due to the switching fall time, tf. The deadtime value in this datasheet is defined as the time period between the beginning of turn-off on one side of the switching stage and the beginning of turn-on on the other side as shown in Figure 19. The fall time of the MOSFET gate voltage must be subtracted from the deadtime value in the datasheet to determine the effective deadtime of a Class D audio amplifier. (Effective deadtime) = (Deadtime in datasheet) – tf 90% HO (or LO) Effective dead - time 10% tf LO (or HO) Dead-time in datasheet 10% Figure 19 Effective Dead Time A longer deadtime period is required for a MOSFET with a larger gate charge value because of the longer tf. Although a shorter effective, deadtime setting is beneficial to achieving better linearity in Class D amplifiers, the likelihood of shoot-through current increases with narrower deadtime settings. Negative values of effective deadtime may cause excessive heat dissipation in the MOSFETs, leading to potentially serious damage. To calculate the optimal deadtime in a given application, the fall time tf for both HO and LO in the actual circuit need to be taken into account. In addition, variations in temperature and device parameters could also affect the effective deadtime in the actual circuit. Therefore, a minimum effective deadtime of 10ns is recommended to avoid shoot-through current over the range of operating temperatures and supply voltages. www.irf.com AN-1158 23 9.2 Programming Deadtime The IRS2053M selects the deadtime from a range of preset deadtime values based on the voltage applied at the DT pin. An internal comparator translates the DT input to a predetermined deadtime by comparing the input with internal reference voltages. These internal reference voltages are set in the IC through a resistive voltage divider using VCC. The relationship between the operation mode and the voltage at DT pin is illustrated in the Figure 20 below. Dead- time 25nS 45nS 75nS 105nS 0.23xVcc 0.36xVcc 0.57xVcc Vcc VDT Figure 20 Deadtime vs. VDT Table 4 suggests pairs of resistor values used in the voltage divider for selecting deadtime. Resistors with up to 5% tolerance are acceptable when using these values. Figure 21 External Voltage Divider for DT Pin Deadtime Mode DT1 DT2 DT3 DT4 R1 <10k 5.6k 8.2k Open R2 Open 4.7k 3.3k <10k DT Voltage Vcc 0.46 x Vcc 0.29 x Vcc COM Table 4 Recommended Resistor Values for Dead Time Selection www.irf.com AN-1158 24 10 Power Supply Considerations 10.1 Supplying VAA and VSS For best audio performance, it is preferred to produce VAA and VSS with external regulators, such as the three terminal regulators. Standard 7805 and 7905 regulators are suitable. Figure 22 Supplying VAA and VSS with External Regulators When switched mode regulators provide VAA and VSS, it is required to place a two-stage noise filter in the supply lines as shown in Figure 23 to prevent noise from influencing the switching ripple voltage on +/-5V. Figure 23 Supplying VAA and VSS from Switched Mode Power Supply www.irf.com AN-1158 25 10.2 Recommended Power Supply Configuration for Gate Driver Stage Figure 24 shows the recommended power supply configuration for gate driver power supplies. Gate driver stage has five power supply inputs. 1. 2. 3. 4. 5. VB1-VS1: CH1 high side gate drive supply VB2-VS2: CH2 high side gate drive supply VB3-VS3: CH3 high side gate drive supply VCC-COM: low side logic supply VCC2-COM2: CH1-3 low side gate drive supply RVBS1 - RVBS3 prevent CVBS1 – CVBS3 from over-charging due to under shoots in VS1 – VS3. RVBS1 - RVBS3 reduce switching noise triggered by Qrr of bootstrap diode DBS1 – DBS3 . All power supplies except VCC-COM generate switching noise. RVCC2 isolates the switching noise from low side gate drive current and bootstrap charge pump current feeding into VCC. These optional filtering resistors are effective to achieve best audio performance in higher power applications (>100W). -Vbus + Vcc CVCC 1 uF RVCC 4.7 -Vbus CVBS2 10 uF RVBS2 4.7 DBS1 CVBS1 10 uF RVBS1 4.7 RVCC2 4.7 CVCC2 1 uF CVBS3 10 uF RVBS3 4.7 DBS3 DBS1 Figure 24 Recommended Power Supply Configurations for Gate Driver Stage www.irf.com AN-1158 26 10.2.1 VCC and VCC2 The Non-floating section of IRS2053M has two supply voltages, VCC and VCC2. The VCC is paired with COM to supply logic and small signal circuitries. The VCC2 and COM2 feed power to LO1-3 low side gate drive stages. It is recommended to supply both VCC and VCC2 from a single supply source. VCC must be equal or higher than VCC2, but no more than 5V. 10.2.2 COM and COM2 COM and COM2 must be tied to each other in as short a distance as possible. 10.2.3 Bottom Pad Connection The Exposed bottom pad in the MLPQ48 package where the IC die sits has the same voltage potential as COM and COM2. However, it is not directly connected inside. The pad may be tied to COM and COM2 with short distance trace(s), or may be floated. Do not use the bottom pad as the low side power supply return path. www.irf.com AN-1158 27 10.3 Designing High-side Bootstrap Power Supply The high-side driver requires a floating supply VBn referring to respective switching node VSn where the source of the MOSFET is connected. A charge pump method (floating bootstrap power supply) eliminates the need of a floating power supply and thus is used in the typical application circuit. 10.3.1 Floating Bootstrap Power Supply The floating bootstrap power supply charges bootstrap capacitor CBS from the low-side power supply VCC during the low-side MOSFET ON period. When the high-side MOSFET is ON, the charging diode turns off to float the VBS supply. CBS retains its voltage as a floating power supply referenced to VS. Before CBS discharges and VBS crosses the under voltage lock out threshold UVBS, the next charging cycle should start by turning on the lowside MOSFET. Figure 25 depicts the low-side MOSFET ON state. I1 turns off the high-side MOSFET first, then I2 turns on the low side the MOSFET. As soon as switching node VS reaches negative supply –B, the bootstrap diode DBS turns on and starts charging CBS with current I3 from VCC. Note that VBS = VCC – (forward drop voltage of DBS). VBn L OFF HOn H ON +B + - CBS I3 DBS OFF I1 -B VSn LEVEL SHIFT VCC2 PWM H L Vcc I2 ON LOn ON 12V L OFF -B COM, COM2 IRS2053M Figure 25 Charging VBS: Low-side ON Period After the low-side conduction period, I4 in Figure 26 turns off the low-side MOSFET. Then I5 turns on the highside MOSFET, lifting VS up to +B. As long as the high side is ON, the bootstrap diode DBS isolates the floating power supply VBS. www.irf.com AN-1158 28 VBn H ON HOn +B + - CBS DBS ON L OFF I5 VSn LEVEL SHIFT VCC2 PWM L H Vcc OFF LOn H OFF 12V ON I4 COM, COM2 -B IRS2053M Figure 26 High-side ON Period 10.3.2 Choosing Bootstrap Capacitance Since a MOSFET is a voltage driven device, I5 is only to fill up the gate charge of the high-side MOSFET during the rising edge that is a one time event for entire high-side MOSFET on-time. After that, no more current flows from CBS. In spite of that, the high-side gate driver stage in the IRS2053M has quiescent current consumption IQBS to drain the charge of CBS during the high-side MOSFET ON-time. High-side sensing bias current IR1 via detecting diode D1 is another current to take into considerations. (Figure 28) Normally, leakage current in the gate of a MOSFET is negligibly small compared to the IQBS and IR1. The minimum bootstrap capacitance is determined as follows. C BS ( I QBS I R1 ) t ON VCC 1.5 UVBS Where CBS: floating bootstrap capacitance [F] IQBS: high-side quiescent current [A] IR1: high-side current sensing bias current [A] tON: longest high-side MOSFET conduction time [s] VCC: low-side power supply voltage [V] UVBS: high-side under voltage lockout threshold [V] 1.5: voltage drop in the bootstrap charging diode DBS The bootstrap capacitor sees the VCC supply voltage. A ceramic capacitor (X7R, X5R or X5S type) or aluminium electrolytic capacitor with 25V or higher voltage rating is recommended. www.irf.com AN-1158 29 VCC - VF UVBS VBS 0 HO Figure 27 VBS Discharging Figure 28 CBS Discharging During High-side ON Period 10.3.3 Choosing Bootstrap Diode The bootstrap diode blocks bus voltage (+B)-(-B) + (voltage overshoot), therefore a diode with voltage rating of 1.5 x bus voltage is a minimum requirement. In order to charge the bootstrap capacitor in a very short low-side ON period in a high PWM modulation ratio, a fast recovery type is necessary. One with a short reverse recovery time of trr<50ns is recommended. www.irf.com AN-1158 30 10.3.4 Damping Resistor Inserting a damping resistor in series with bootstrap diode DBS is an effective way to eliminate the following potential problems in bootstrap power supply design. EMI noise due to reverse recovery charge of the bootstrap diode; note that this diode is a switching device for the charge pump Overcharge to bootstrap supply capacitor CBS Figure 29 explains how the floating supply voltage VBS is over charged by a negative spike on VS voltage that is induced by stray inductances in –B feeding line. Generally, a 1 to 5 ohms resistor helps to prevent these issues. Figure 29 VBS Charging With and Without RBS www.irf.com AN-1158 31 10.3.5 Charging VBS Prior to Start For proper start-up, it is necessary for the high side bootstrap capacitor be charged prior to PWM start-up through a resistor RCHARGE from the positive supply bus to the VB pin. By utilizing an internal 15.3V Zener diode between VB and VS, this scheme eliminates the need to charge the boot strap capacitor through low side turn on during start up. The value of this charging resistor is subject to several constraints: - The minimum resistance of RCHARGE is limited by the maximum PWM modulation index of the system. When HO is high, RCHARGE drains the bootstrap power supply so it reduces holding up time, hence maximum continuous HO on time. - The maximum resistance of RCHARGE is limited by the current charge capability of the resistor during startup: I CHARGE I QBS where ICHARGE = the current through RCHARGE IQBS = the high side supply quiescent current. ICHARGE generates a DC offset at the speaker output prior to PWM start up. Check that the DC offset does not exceed a condition for click noise elimination. See Click Noise Elimination section for more detail. Figure 30 Boot Strap Supply Pre-charging www.irf.com AN-1158 32 10.4 Start-up Sequence (UVLO) The protection control block in the IRS2053M monitors the status of VAA and VCC to ensure that both voltage supplies are above their respective UVLO (under- voltage lockout) thresholds before beginning normal operation. If either VAA or VCC is below the under voltage threshold, LO and HO are disabled in shutdown mode until both VAA and VCC rise above their voltage thresholds. 10.4.1 Power-down Sequence As soon as VAA or VCC falls below its UVLO threshold, protection logic in the IRS2053M turns off LO and HO, shutting off the power MOSFETs. Figure 31 IRS2053M UVLO Timing Chart www.irf.com AN-1158 33 10.5 Power Supply Decoupling Because the IRS2053M contains analog circuitry, careful attention must be given to decoupling the power supplies for proper operation of the IC. Ceramic capacitors minimum of 0.1µF or aluminium capacitors minimum of 1uF should be placed close to the power supply pins of the IC on the board. Due to large capacitance variations, Y5V dielectric or similar type ceramic capacitors are not recommended. Please refer to the application note AN-978 for general design considerations of a high voltage gate driver IC. www.irf.com AN-1158 34 11 Junction Temperature Estimation The power dissipation in the IRS2053M is dominated by the following items: - PMID: Power dissipation of the input floating logic and protection circuitry - PLSM: Power dissipation of the Input Level Shifter - PLOW: Power dissipation in low side - PLSH: Power dissipation of the High-side Level Shifter - PHIGH: Power dissipation in high side The following equations are for reference only. Because of the non-linear characteristics in gate drive stage, these assumptions may not be accurate. 11.1 PMID: Power Dissipation of the Input Floating Logic and Protection Circuitry The power dissipation of the input floating section is given by: PMID V AA V SS I QAA1 Where IQAA1 = floating input section quiescent supply current in normal operation mode 11.2 PLSM: Power Dissipation of the Input Level Shifter PLSM = 1.5 x 10-9 x fSW x VSS BIAS x 3 Where fSW = the PWM switching frequency VSS BIAS = the bias voltage of VSS with respect to COM 11.3 PLOW: Power Dissipation of Low Side The power dissipation of the low side comes from the losses of the logic circuitry and the losses of driving LO. PLOW PLDD 3 PLO RO I QCC VCC 3 Vcc Qg f SW R R R O g g (int) Where PLDD = power dissipation of the internal logic circuitry PLO = power dissipation from of gate drive stage for LO RO = output impedance of LO, typically 20 Ω for the IRS2053M www.irf.com AN-1158 35 Rg(int) = internal gate resistance of the low side MOSFET, typically 2Ω Rg = external gate resistance of the low side MOSFET Qg = total gate charge of the low side MOSFET 11.4 PLSH: Power Dissipation of the High-side Level Shifter PLSH = 0.4nC x fsw x VBUS x 3 Where fSW = PWM switching frequency VBUS = difference between the positive bus voltage and negative bus voltage 11.5 PHIGH: Power Dissipation of High Side The power dissipation of the high side comes from the losses of the logic circuitry and the losses of driving HO. PHIGH 3 ( PLDD PHO ) RO 3 I QBS VBS 3 VBS Qg f SW R R R O g g (int) Where PLDD = power dissipation of the internal logic circuitry PHO = power dissipation of the gate drive stage for HO RO = equivalent output impedance of HO, typically 20 Ω for the IRS2053M Rg(int) = the internal gate resistance of the high side MOSFET, typically 2Ω Rg = external gate resistance of the high side MOSFET Qg = total gate charge of the high side MOSFET 11.6 PD: Total Power Dissipation Total power dissipation, PD, is given by PD PMID PLSM PLOW PHSM PHIGH . www.irf.com AN-1158 36 11.7 TJ: Junction Temperature Given junction to ambient thermal resistance RthJA, the junction temperature TJ can be calculated from the formula provided below and must not exceed 150°C. T J [ Rth JA Pd T A ] 150 C www.irf.com AN-1158 37 12 Board Layout Considerations The floating input section of the IRS2053M consists of a low noise OTA error amplifier and a PWM comparator along with CMOS logic circuitry. The high frequency bypass capacitor CVAA-VSS should be placed closest to the IRS2053M to supply the logic circuitry. CVAA and CVSS are for stable operation of the OTA and should be placed close to the IC. Gate driver supply capacitors CVCC, CVCC2, CVBS1, CVBS2 and CVBS3 provide gate-charging current and should also be placed close to the IRS2053M. CVAA CVSS CVCC CVBS2 CVBS3 CVBS1 CVCC2 Figure 32 Placement Sensitive Bypass Capacitors www.irf.com AN-1158 38 12.1 Ground Plane In addition to the key component locations mentioned above, it is important to properly pour ground planes to obtain good audio performance. Since each functional block within the IRS2053M refers to different potentials, it is recommended to apply three reference potentials. 12.1.1 Analog Ground The Input analog section around the OTA is referenced to the signal ground, or GND, which should be a quiet reference node for the audio input signal. The peripheral circuits in the floating input section such as CSD and COM pins refer to this ground. These nodes should all be separate from the switching stages of the system. In order to prevent potential capacitive coupling to the switching nodes, use a ground plane only in this part of the circuit. Do not share the ground plane with gate driver or power stages. 12.1.2 Gate Driver Reference The gate driver stage of the IRS2053M is located between pins 7 and 30 and is referenced to the negative bus voltage, COM and COM2. This is the substrate of the IC and acts as ground. Although the negative bus is a noisy node in the system, both of the gate drivers refer to this node. Therefore, it is important to shield the gate drive stages with the negative bus voltage so that all the noise currents due to stray capacitances flow back to the power supply without degrading signal ground. 12.1.3 Power Ground Power ground is the ground connection that closes the loops of the bus capacitors and inductor ripple current circuits. Separate the power ground and input signal grounds from each other as much as possible to avoid common stray impedances. Figure 33 illustrates how to paint out reference planes. The power GND plane should include a negative bus cap. Power reference plane should include Vcc. Also, use distinctly different symbols for the different grounds. For further board layout information, refer to AN-1135, PCB Layout with IR Class D Audio Gate Drivers www.irf.com AN-1158 39 CH3 INPUT -5V +5V CH2 INPUT SIGNAL GND CH1 INPUT FAULT CH1 CLIP CH2 CLIP CH3 CLIP CLK INPUT (optional) VCC +B CH2 OUTPUT CH1 OUTPUT -B POWER GND CH3 OUTPUT Figure 33 Applying Ground Planes www.irf.com AN-1158 40 Revision History Date 1/22/2010 2/27/2010 6/9/2010 www.irf.com Change Initial issuance Proofread Added Events and Fault table AN-1158 41