P3MS650103H D

P3MS650103H
1.8V/2.5V/3.3V, LVCMOS
Peak EMI Reduction Clock
Generator
Product Description
P3MS650103H device is a spread spectrum frequency modulator
clock generator with 1.8 V/2.5 V/3.3 V LVCMOS output designed
specifically for clock frequencies between 15 MHz and 60 MHz.
P3MS650103H reduces electromagnetic interference (EMI) at the
clock source, allowing system wide reduction of EMI of all clock
dependent signals. The device allows significant system cost savings
by reducing the number of circuit board layers, ferrite beads, and
shielding that are traditionally required to pass EMI regulations.
P3MS650103H accepts an LVCMOS input from an external
reference clock and locks to a 1x modulated clock output.
P3MS650103H goes to power down mode for power save when no
clock is present on CLKIN pin. ModOUT goes ‘low’ in power down
mode.
P3MS650103H operates over −20°C to +85°C and is available in a 4
Pin WDFN, (1.2mmX1.0mm) Package.
http://onsemi.com
MARKING
DIAGRAM
WDFN4
CASE 511BS
1
B = Specific Device Code
M = Date Code
PIN CONFIGURATION
Features
• Peak EMI Reduction Clock Generator with LVCMOS Output
• Supply Voltage and Input / Output Clock Frequency Range
•
•
•
•
•
•
1.6 V − 2.0 V: 15 MHz − 30 MHz
2.3 V − 3.6 V: 15 MHz − 60 MHz
Frequency Deviation:
±0.45% @ 24 MHz
Power Down current less than 1 mA
4−pin WDFN (1.2mmX1.0mm) Package
Output Drive Current: 1.8 V:
8 mA
2.5 V/3.3 V: 16 mA
Operating temperature range: −20°C to +85°C
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
BM
1
VSS
1
4
VDD
CLKIN
2
3
ModOUT
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 6 of this data sheet.
Applications
• P3MS650103H is targeted towards consumer electronic applications
like mobile Phones, tablets, net books and MIDs
VDD
4
CLKIN
PLL
+
Frequency
Modulator
2
1
ModOUT
3
VSS
Figure 1. Simplified Block Diagram
© Semiconductor Components Industries, LLC, 2011
September, 2011 − Rev. 0
1
Publication Order Number:
P3MS650103H/D
P3MS650103H
Table 1. PIN DESCRIPTION
Pin #
Pin Name
Type
1
VSS
Power
Description
2
CLKIN
Input
3
ModOUT
Output
Spread Spectrum Clock Output.
4
VDD
Power
Power supply for the entire chip
Ground connection.
LVCMOS External reference clock input.
Table 2. OPERATING CONDITIONS
Symbol
VDD (1.8 V)
Description
Supply Voltage with respect to VSS
VDD
(2.5 V/3.3 V)
Min
Max
Unit
1.6
2.0
V
2.3
3.6
−20
+85
°C
TA
Operating temperature
CL
Load Capacitance
15
pF
CIN
Input Capacitance
5
pF
Table 3. ABSOLUTE MAXIMUM RATING
Symbol
VDD, VIN
TSTG
Description
Rating
Unit
Voltage on any input pin with respect to VSS
−0.5 to +4.6
V
Storage temperature
−65 to +125
°C
Ts
Max. Soldering Temperature (10 sec)
260
°C
TJ
Junction Temperature
150
°C
2
kV
TDV
Static Discharge Voltage (As per JEDEC STD22− A114−B)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may
affect device reliability.
http://onsemi.com
2
P3MS650103H
Table 4. DC Electrical Characteristics VDD = 1.6 V − 2.0 V, TA= −20°C to +85°C
Symbol
Parameter
Min
Typ
Max
Unit
1.6
1.8
2.0
V
15MHz
1.3
1.8
30MHz
2
2.8
VDD
Supply Voltage with respect to VSS
IDD
Dynamic supply current
(Unloaded Output)
ICC
Static supply current (No Clock @ CLKIN)
VIH
Input high voltage
VIL
Input low voltage
0.3*VDD
V
IIH
Input high current (CLKIN pin)
10
mA
IIL
Input low current (CLKIN pin)
10
mA
VOH
Output high voltage, IOH = − 8mA
VOL
Output low voltage , IOL = 8mA
ZOUT
Output impedance
mA
1
mA
0.65*VDD
V
0.75*VDD
V
0.2*VDD
28
V
W
Table 5. AC ELECTRICAL CHARACTERISTICS VDD = 1.6 V − 2.0 V, TA = −20°C to +85°C
Symbol
CLKIN
ModOUT
Parameter
Min
Typ
Max
Unit
Input Clock frequency
15
30
MHz
Output Clock frequency
15
30
MHz
tLH
(Notes 1 and 2)
Output rise time
(Measured between 20% to 80%)
1.7
2.7
nS
tHL
(Notes 1 and 2)
Output fall time
(Measured between 80% to 20%)
1.4
2.4
nS
tJC (Notes 2)
Cycle−to−cycle Jitter, Peak
(1000 cycles)
15 MHz
400
24 MHz
250
pS
30 MHz
tD
(Notes 1 and 2)
Output duty cycle (Measured @ 50%)
tON
(Notes 1 and 2)
PLL lock Time
(Stable power supply, valid clock presented on CLKIN)
fd
45
Frequency Deviation @ 24 MHz
50
±0.45
1. All parameters are specified with 15 pF loaded output.
2. Parameter is guaranteed by design and characterization. Not 100% tested in production
http://onsemi.com
3
55
%
3
mS
±0.52
%
P3MS650103H
Table 6. DC ELECTRICAL CHARACTERISTICS VDD = 2.3 V – 3.6 V, TA = −20°C to +85°C
Symbol
Parameter
VDD
Supply Voltage with respect to VSS
IDD
Dynamic supply current
(Unloaded Output)
ICC
Static supply current (No Clock @ CLKIN)
VIH
Input high voltage
VIL
Input low voltage
IIH
IIL
Min
Typ
Max
Unit
2.3
2.8
3.6
V
15MHz
1.7
3
30MHz
2.8
5
60MHz
5
9
mA
2
mA
0.65 * VDD
V
0.3 * VDD
V
Input high current (CLKIN pin)
10
mA
Input low current (CLKIN pin)
10
mA
VOH
Output high voltage, IOH = −16 mA
VOL
Output low voltage, IOL = 16 mA
ZOUT
Output impedance
0.75 * VDD
V
0.2 * VDD
20
V
W
Table 7. AC ELECTRICAL CHARACTERISTICS VDD = 2.3 V – 3.6 V, TA = −20°C to +85°C
Symbol
CLKIN
ModOUT
Parameter
Min
Typ
Max
Unit
Input Clock frequency
15
60
MHz
Output Clock frequency
15
60
MHz
tLH
(Notes 3 and 4)
Output rise time
(Measured between 20% to 80%)
0.8
1.6
nS
tHL
(Notes 3 and 4)
Output fall time
(Measured between 80% to 20%)
0.8
1.6
nS
tJC (Notes 4)
Cycle−to−cycle Jitter, Peak
(1000 cycles)
tD
(Notes 3 and 4)
Output duty cycle
tON
(Notes 3 and 4)
PLL lock Time
(Stable power supply, valid clock presented on CLKIN)
fd
15 MHz
350
24 MHz
250
60 MHz
100
45
Frequency Deviation @ 24 MHz
50
±0.45
3. All parameters are specified with 15 pF loaded output.
4. Parameter is guaranteed by design and characterization. Not 100% tested in production
http://onsemi.com
4
pS
55
%
3
mS
±0.70
%
0.70
0.70
0.60
0.60
0.50
0.50
DEVIATION (±%)
DEVIATION (±%)
P3MS650103H
0.40
0.30
0.20
0.10
0.00
15
0.40
0.30
0.20
0.10
20
25
FREQUENCY (MHz)
0.00
15
30
20
Figure 2. Deviation vs. Frequency
(VDD = 1.6 V − 2.0 V)
VDDIN
35
40
45
30
FREQUENCY (MHz)
50
55
60
Figure 3. Deviation vs. Frequency
(VDD = 2.3 V − 3.6 V)
Noise Reduction Filter
C1
C2
R
VDD
0.1mF
2.2mF
4
CLKIN
CLKIN
25
ModOUT
2
Rs
3
ModOUT
P3MS650103H
VSS
1
Rs = Trace Impedance of PCB – Output Impedance of Device (Z0)
Note: Refer Pin Description table for Functionality details
Figure 4. Typical Application Schematic
PCB Layout Recommendation
For optimum device performance, following guidelines are recommended.
♦ Dedicated VDD and GND planes.
♦ The device must be isolated from system power supply noise. A 0.1mF and a 2.2 mF decoupling capacitor should be
mounted on the component side of the board as close to the VDD pin as possible. No vias should be used between the
decoupling capacitor and VDD pin. The PCB trace to VDD pin and the ground via should be kept as short as
possible. All the VDD pins should have decoupling capacitors.
♦ In an optimum layout all components are on the same side of the board, minimizing vias through other signal layers.
http://onsemi.com
5
P3MS650103H
A typical layout is shown in the figure below.
Figure 5. Recommended PCB Layout
ORDERING INFORMATION
Ordering Code
P3MS650103H−4CR
Marking
Temperature
Package Type
Shipping†
B
−20°C to +85°C
4−pin (1.2 mm x 1.0 mm) WDFN
(Pb−Free)
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*A “microdot” placed at the end of last row of marking or just below the last row toward the center of package indicates Pb−Free.
http://onsemi.com
6
P3MS650103H
PACKAGE DIMENSIONS
WDFN4, 1.0x1.2, 0.5P
CASE 511BS−01
ISSUE O
PIN ONE
REFERENCE
2X
ÉÉ
ÉÉ
E
0.05 C
2X
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND
0.20 mm FROM THE TERMINAL TIPS.
4. PACKAGE DIMENSIONS EXCLUSIVE OF
BURRS AND MOLD FLASH.
A
B
D
DIM
A
A1
A3
b
D
E
e
L
0.05 C
TOP VIEW
(A3)
0.05 C
A
MILLIMETERS
MIN
MAX
0.70
0.80
0.00
0.05
0.20 REF
0.20
0.30
1.00 BSC
1.20 BSC
0.50 BSC
0.35
0.45
0.05 C
SIDE VIEW
e
A1
e/2
2
1
4
3
4X
C
SEATING
PLANE
RECOMMENDED
MOUNTING FOOTPRINT*
0.50
PITCH
L
3X
0.63
PACKAGE
OUTLINE
1.50
4X
b
0.05
BOTTOM VIEW
M
C A B
NOTE 3
4X
0.30
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
7
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
P3MS650103H/D